Beko’s two -chamber refrigerator does not cool the upper chamber

Why is the refrigerator not freezing, but the freezer works

It happens that during the operation of equipment the refrigerator stops freezing, and the freezer at the same time works. You can suspect something wrong with sour milk in the refrigerator or other spoiled products. Super.loving users measure the temperature in the refrigerator and find out that there is heat.

In this article, we consider the possible reasons why the refrigerator does not work, and the freezer works for two.chamber refrigerators of different devices. Here in the refrigerators of which type, problems of this nature happen:

  • No Frost in both cameras (Full No Frost);
  • one.compressor models with a drip on a refrigerator, a freezer, which needs to be defrosted manually, and separately control the temperature in the chambers (two thermostats, its own for each compartment);
  • Two.compressor refrigerators.

Why is the refrigerator full no frost does not freeze, and the freezer freezes

In refrigerators with No Frost in both chambers, one evaporator. He is in the freezer. The cooling of the refrigerator department occurs due to the fan, which drives cold air through special channels from the evaporator in the freezer. The air flow is adjusted to the damper. She blocks his feed when the refrigerator compartment was cooled enough. In the evaporator is the heater, which periodically turns on and thaws the resulting ice. Therefore, no frost refrigerators do not need defrosting.

The refrigerator does not cold: what to do

Immediately understand that the refrigerator is warming inside and does not cold as before, it is difficult. The fact that a failure occurred in the operation of the unit, says quick damage to products. If the refrigerator is badly freezing, first check the availability of power on the network. The light bulb burning inside the camera indicates that there are no problems with this. Look if the “defrosting” mode is turned on.

To search for reasons, it is recommended to study the instructions for the device for the device, which listed common cases of malfunctions and their causes. They are characteristic of all models of Samsung, Indesit, Beko, “Biryusa” and others. So, for example, why the Lumus refrigerator refrigerator is badly freezed, for example?

The technical documentation indicates the following reasons:

  • high external temperature;
  • too many products are loaded at the same time;
  • unheated products;
  • Frequent opening of the refrigerator door.

If the kitchen is hot or the unit is installed near heating devices, the entire power of the engine in a one.compressor device is spent on maintaining the required temperature regime in the freezer. It is not enough for the full cooling of the refrigerator. So that the compressor power is distributed to both compartments, reduce the given temperature.

If the refrigerator is often opened, overloaded or placed in it warm products, to correct the situation, observe the rules of operation of a household appliance.

To understand why the upper chamber of the refrigerator does not cold, it is also necessary to check how tightly the unit door is closed. When warm air enters the refrigerator, the products do not have time to cool. In this case, ice forms on the walls. The products and utensils placed in the device can interfere with dense fitting. They are moved and the door is closed so that the temperature comes back to normal. If there is a snow fur coat, the unit is defrosted.

The cause of warm air enters the chamber may consist in wear or damage to the rubber seal. If the gasket is torn, it is changed to the original part. Replacement is carried out independently or with the help of a master.

From long operation or use of household chemicals, the elastic band becomes stiff. In this case, they do not change it, but restore elasticity. Carefully removed from the door, lower it into hot water and left until it cools completely. Then dry and returned to place. This procedure helps restore lost properties.

beko, chamber, refrigerator, does, cool

In units with the No Frost system, the reason that the freezer is freezing and the refrigerator is not, there may be freezing of the fan. If he is silent or creaks loudly (the blades rub on the ice), they defrost the unit to eliminate the problem.

Reference. In order for the technique to be completely thawed, it is thawed for at least 10 hours, after which it is thoroughly wiped and allowed to stand the unit.

If with operation, mode, door and fan everything is in order, the unit is recommended to turn off, defrost and call the master. Either try to find the reason for why the freezer is freezing in the refrigerator, and the refrigerator itself is not.

Diagnosis of breakdowns

If you are faced with the fact that the freezer as before works, and the refrigerator has stopped, then you need to check the following:

  • Check all the nozzles and the radiator for the presence of leaks and trims, as this may be the main reason for the trouble.
  • Look at thermal attires or not, if the compressor does not start again, then most likely the reason is in the sensor. They are inexpensive, and you can replace them with your own hand.
  • Make sure the compressor is working, in some models of refrigerators, 2 is installed. Therefore, everyone will have to check for performance.

Stinol refrigerator malfunctions

STINOL refrigerators, as well as for other brands, are characterized by typical malfunctions. Users of two.compressor models are faced with the following breakdown: there is no cold in the upper chamber, the motor does not start, but the light burns. Perhaps one of the compressors is hot, while the other does not heat up.

  • Problems with the operation of a thermostat or air sensor. In this case, the motor turns on as usual, but its “rest” is delayed for a long time. The electronic module does not receive a signal from the sensors, so the camera does not cool.
  • The launched relay failed. Perhaps he was jammed in one position, so the motor does not start. Diagnostics and replacement of a faulty part are carried out.
  • Fan problems. You noticed that the fan is blocking the ice and defrosted the refrigerator. But after defrosting, the part did not start working. Will have to check and replace the fan electric motor.

As in previous cases, the cause of the breakdown could be a compressor or a refrigerant leak. Complete diagnosis of refrigeration equipment is carried out.

Incorrect installation

The principle of operation of the refrigerator is not “cold production”. He simply removes excess heat from the camera out through the heat exchanger on the back wall. If the refrigerator is installed near the device giving heat (radiator, slabs), it will not be normally cold.

An important role is played by the distance to the walls and position. There are several basic installation rules:

  • It is not recommended to put the refrigerator in the corner;
  • The distance from the heat exchanger to the wall. at least 10 cm;
  • Do not hang lockers or shelves above the refrigerator.

The distance to the walls depends on the volume of the refrigerator, power, the location of the heat exchanger. Some manufacturers have special requirements. Therefore, read the instructions so that there are no problems with operation.

Beko’s two.chamber refrigerator does not cool the upper chamber

The following reasons that occur in the case when the refrigerator does not cool are indicated from the most probable to the least probable. Check or test each reason, starting with the most likely reasons.

Reason 1 polluted capacitor coils

Condenser coils are usually located under the refrigerator. They dissipate heat with the help of a refrigerant circulating through them. If condenser coils are contaminated, then they will not effectively dissipate heat. As the dirt accumulates on the reels, the refrigerator becomes less effective, as a result of which it takes more time to cool. If the coils are very contaminated, then the refrigerator will not be able to maintain the proper temperature. Check the capacitor coils to determine if they are polluted, and if so, clean them.

Reason 2 of the capacitor fan engine

The capacitor fan engine blows with air condenser coils and compressor. If the capacitor fan engine does not work incorrectly, then the refrigerator will not cool properly. To determine whether the fan engine is defective, first check the fan blades for any obstacles. Then try to manually turn the fan blades. If the blades rotate with difficulty, then replace the capacitor fan engine. If there are no obstacles and the fan blades rotate freely, then use the multimeter to check the fan engine for continuity. If the continuity of the capacitor fan engine is violated, then replace it.

Reason 3 Epiphany fan engine

The evaporator fan electric motor blows overdue (cooling) coils with air and circulates air throughout the refrigerator and departments of the freezer. Some refrigerators have two evaporator fan engines. In refrigerators with one evaporator, it is located in the freezer. If the evaporator fan does not work, then it will not circulate cold air in the refrigerator compartment. If this happens, then the freezer can still be cold, but there is no refrigerator. To determine whether the evaporator fan engine is defective, try to manually turn the fan blades. If the fan blades rotate with difficulty, replace the fan engine. In addition, if the engine is too noisy, then replace it. Finally, if the engine does not work at all, then use a multimeter to check the engine winding to ensure continuity. If the continuity of the winding is broken, then replace the evaporator fan engine.

The starting relay works in combination with the launch winding to start the compressor. If the starting relay is malfunctioning, then the compressor may sometimes not start or not work at all. As a result, the refrigerator will not be cold as it should. To determine whether the starting relay is faulty, use the multimeter to check it for continuity between the connectors and starts. If the continuity of the starting relay is broken, then replace it. In addition, if the starting relay has a burning smell, then replace it.

Reason 5 Thermostat of temperature control

The thermostat of temperature control supplies the voltage to the compressor, the evaporator fan engine and the capacitor fan engine (if applicable). If the temperature thermostat the temperature is not proper, then this may interfere with the operation of the refrigerant system. To determine whether the thermostat is faulty, turn the thermostat from a minimum temperature to maximum to hear a click. If the thermostat closes, then it is unlikely to be broken. But if the thermostat has not clicked, then use the multimeter to check its continuity. If the continuity of the temperature thermoregulator is disturbed, then replace it.

Reason 6 launcher capacitor

The start.up capacitor provides an increase in compressor power during launch. If the start.up capacitor does not work, then the compressor does not start. As a result, the refrigerator does not cool. To determine whether the start.up capacitor is faulty, check it using a multimeter. If the start.up capacitor is faulty, then replace it.

Thermistor controls the temperature of the refrigerator and sends the temperature indications to the control board. The control panel regulates the power of the compressor and fan of the evaporator based on the readings of the termistor. If the termistor is faulty, then the compressor and fan of the evaporator may not work when you need. As a result, the refrigerator will be poorly cold. To determine whether the termistor is faulty, check it using a multimeter. The resistance of the termistor should vary depending on the temperature of the refrigerator. If the resistance of the termistor does not change or the termistor has no continuity, then replace it. Reason 8 Temperature control board

The temperature control board supplies voltage for compressor and fan engines. If the temperature control board is faulty, then it will stop supplying current to the cooling system. But this is rare. Control panels are often erroneously diagnosed. therefore, before replacing the control board, first check more and more more often breaking components. If all other components work, then think about replacing the temperature control boards.

The compressor is a pump that pumps a refrigerant and circulates it through the evaporator and condenser coils. If the compressor does not work, then the refrigerator does not cool. However, this rarely happens. Before replacing the compressor, first check more and more broken components. If you have determined that all other components work correctly, then check the compressor. Use a multimeter to check the continuity between compressor electrical contacts. If there is a chain break, then the compressor is probably faulty and it should be replaced by inviting a licensed master.

Reason 10 main control board

Perhaps the main control board is faulty. However, this is very rare. Before replacing the main control board, check more and more broken components. If you have determined that all other components work correctly, then think about replacing the main control board.

Beko‘s two.chamber refrigerator does not cool the upper chamber

The following reasons that occur in the case when the freezer freezer works, and the refrigerator does not cold, are indicated from the most probable to the least probable. Check or test each reason, starting with the most likely reasons. Reason 1 Frozen the evaporator coils

The heating device of the sealing is turned on several times during the day to melt any frustration that can be accumulated on the evaporator coils. If the thawing heater block is defective, then the frost will continue to accumulate on the reels of the evaporator and forget the coils. If the evaporative coils freeze, then this will limit the flow of air passing through them, as a result of which the refrigerator does not cool. Check the evaporator coils to determine the presence of frosts on them. If the evaporator coils are frozen, then check each component of the defrosting system.

Reason 2 of the evaporator fan engine

The evaporator fan engine supplies cold air through the evaporator coils and circulates throughout the freezer. If the evaporator fan does not work, then the freezer or refrigerator will not work normally. To determine whether the evaporator fan engine is defective, try to handle the fan blad manually. If the fan blad does not rotate freely, then replace the fan engine. In addition, if the engine is too noisy, then replace it. Finally, if the engine does not work at all, then use a multimeter to check the engine winding for continuity. If the continuity of the winding is broken, then replace the evaporator fan engine. Reason 3 Dampfer control unit

How to go in SFT Mode in Beko Refrigerator

The control of the air damper (dampfer) is opened and closed to ensure a sufficient amount of cold air in the refrigerator compartment. If the damper does not open properly, then it will not let cold air into the refrigerator. Check the control of the air damper (damper) to determine if it is broken or closed and not surrounded.

Thermistor controls the temperature of the refrigerator and sends the temperature indications to the control board. Then the control board regulates the power of the compressor and fan of the evaporator based on the readings of the termistor. If the termistor is faulty, then the compressor and evaporator fan may not work if necessary or can work too often. To determine whether the termistor is faulty, check it using a multimeter. The resistance of the termistor should vary depending on the temperature of the refrigerator. If the resistance of the termistor does not change or the continuity of the thermistor is broken, then replace it.

Reason 5 temperature control board

beko, chamber, refrigerator, does, cool

The temperature control board regulates the current supply for compressor and fan engines. If the control board is faulty, then it may stop supplying voltage to the compressor or fan engines. Control panels are often erroneously diagnosed. therefore, before replacing the control board, first check all the other more often broken components. If none of the other components is broken, then think about replacing the temperature control board.

Reason 6 Thawing Management Plant

The defrosting control board (thawing) determines how often to start the defrosting cycle. If the thawing control board does not work, then the refrigerator will not run the defrosting cycle, and the frost will continue to accumulate on the heels of the evaporator. If the evaporative coils freeze, then the refrigerator will work more intensively to cool. As a result, the refrigerator can be too warm. If the thermostat is shared and the thawing heater operates correctly, then most likely, the reckoning control board is faulty and it will need to be replaced.

Reason 7 Timer Tight

Beko RFF 273IF Demo

The latrice timer includes a defrosting heater several times during the day to melt any frost.free that can accumulate on the evaporator coils. If the defrosting timer is faulty, then it may not go into the cycle of hidden, or will not give a current to the heating heater during the defrosting cycle. If the defrosting system does not work, then the frost will continue to accumulate on the heels of the evaporator, and the refrigerator will have to work more for cooling. As a result, the refrigerator can be too warm. To determine whether the thawing timer is faulty, slowly switch the toggle switch to the defrosting cycle. The compressor should turn off, and the heater must turn on. If the timer does not supply power to the components of defrosting or does not leave the defrosting cycle for 30 minutes, then this means that the timer is not working and requires replacement.

Reason 8 Thermostat of Defrosting

The thermostat of defrosting controls the temperature of the evaporator coils. Когда катушки охлаждаются ниже заданной температуры, термостат срабатывает, чтобы обеспечить подачу питания на нагреватель оттайки во время цикла размораживания. In the defrosting cycle, the thawing heater melts any frost.free, which can accumulate on the reels of the evaporator. If the thermostat of defrosting is defective, then it will not work, as a result of which the current will not get to the heating heater. To determine whether the thermostat is defective, use the multimeter to check it for continuity. If the continuity of the thermostat of defrosting is violated when the low temperature of the working range is reached, then replace it. Reason 9 Main control

Perhaps the main management fee is faulty, but this is rarely the cause of the problem. Before replacing the control fee, first check more and more broken components. If none of these components is broken, then consider the possibility of replacing the main control board.

Beko CSK 38000 refrigerator malfunctions

A separate Beko two.door refrigerator with the bottom of the freezer is equipped with a drip defrosting of the upper chamber. The freezer is freed from ice manually. The temperature control in the refrigerator is electromechanical.

The following nodes are problematic in the device:

Freon tubes are used steel. The contour wound in the doorway is gradually corroded by a refrigerant, rusts, after 5-7 years a replacement of the contour will be required due to the leakage of the freon.

The condenser grille on the case outside is gradually clogged, the conditional passage decreases. If it is not washed with a frequency of 5-7 years, the performance of the unit will fall, the load on the compressor will increase, the formation of traffic jams in the capillary tube will be provoked. This can lead to expensive repair or replacement of the compressor.

The electromechanical temperature sensor by the manufacturer is programmed for 5 years of work. If a malfunction occurs in the chambers, the compressor works for wear or does not turn on. You can eliminate the malfunction by replacing the device.

The mode in the chambers can be disturbed when the freon leakage. Sign. an ice fur coat appeared in the refrigerator and the temperature rose, and everything is in order in the freezer. With normal mode, in the refrigerator and the melted freezer, it is necessary to check and replace the control board.

There are a lot of reasons for the poor work of the refrigerator, signs of malfunctions differ in some nuances. Accurate diagnostics and repair should be entrusted to specialists.

Using the refrigerated cabinets Becko

It is permissible to connect the refrigerator to the mains after checking the interior departments for cleanliness and installing the unit for the prepared place in the room. Next, such manipulations are performed:

  • Using adjusting components or buttons on the screen (display), set the necessary temperature regime. Part of the models is equipped with an air ionization device in departments.
  • The temperature regime is set at its own discretion of the owner, but the manufacturer advises to exhibit.18 ̊s in the case of a freezer and 4 ̊s for a refrigerator compartment.
  • Когда температура окружающей среды превышает отметку 30 ̊С, то надо выставлять показатели для морозильной камеры на уровне.20 ̊s.
  • To quickly defrost the freezer, use a specially developed function when it is provided by the manufacturer.
  • Before starting fast defrosting, a specialized tank is checked, which is equipped with a Beko refrigerator.

Advice! All the fluid formed during the thawing of the unit enters the specialized container. therefore it is important to correctly place it to prevent the formation of a puddle next to the refrigerators.

Malfunctioning 1 compressor refrigerator Atlant

One.compressor refrigerator, in the presence of two cooling zones, uses a common heat selection scheme. In this case, first of all, the refrigerant is fed into the freezer, then enters the chamber with plus temperature for cooling.

Charges requiring specialized repair include:

If a red bulb is burning, an analysis of the situation is needed.

If a refrigerator does not work in a one.compressor model, and the freezer operates, it means that you need to check if the fan blades are overgrown with ice, distilling the cold air. Perhaps the fan will have to be changed. Maybe the heater of the evaporator has broken, on which the olter. Ice melts. the fan will work.

The temperature in the refrigerator will increase if the light bulb is on the camera. It is necessary to check the door compaction. You can not set the maximum values ​​on the regulators. the freezer will receive its portion of the cold, and the refrigerator chamber will not be enough. Meanwhile, the equipment works for wear, not far from the accident.

Falf refrigerator Beko

Beko has long been widely represented on the market and, thanks to its relatively low price, managed to win the hearts of many consumers. Like any other technique, the refrigerators of this company periodically fail and require repair. In order to return the refrigerator to life and after six months not to encounter re.breakdown, it is recommended to apply for the repair in certified workshops that have experience in repairing techniques of this brand.

How to investigate and fix a fridge that is too warm

The main causes of the breakdown

Most of Beko refrigerators are associated with poor or excessive freezing, high noise or the wrong operation of the device itself. In order to have an idea of ​​the complexity of the repair, it is necessary to separately consider each of the options.

Bad or excessive frost.

If the refrigerator does not freeze at all or does it not well enough, then you need to consider the following reasons:

Low voltage can lead to the fact that the refrigerator engine will operate, but at the same time it will not reach the desired power, which will provide poor freezing or its complete absence. As a rule, the second option is observed. the compressor is buzzing, but does not freeze.

Sometimes low energy consumption leads to the fact that the refrigerator does not turn on at all or turns off a few minutes after the start of work.

Quiet doors of the Beko are loosely closed leads to the fact that warm air constantly penetrates the chamber, the refrigerator cannot reach the desired temperature, the products in it spoil, a large amount of ice forms on the door. The reason for the preventing closing may be intended ice, products or spoiled sealing gum.

With the improper operation of the thermostat, the refrigerator “thinks” that he has reached the desired temperature, but in fact this is not so. The elimination of the problem is by replacing the spoiled node. It is worth noting that this breakdown is eliminated quickly and inexpensive. Contact our company, repair the refrigerator in Saratov with a specialist’s departure at home will take only 30-40 minutes.

GE Refrigerator Won’t Cool. Easy Ideas on how to Fix a Refrigerator Not Cooling

Freon leakage or clogged channels for its spread prevent cooling. To eliminate the problem, you need to find a block of blockage or leakage, eliminate it and, if necessary, get a freon. Such work can only be carried out by the masters of the service center.

The freezer upper chamber is badly freezing.

There are several options for a breakdown at once:

  • incorrectly set settings;
  • clogging of the drainage system;
  • incorrect work of the thermostat;
  • blockage in the capillary system;
  • In refrigerators like No Frost. a sealing gum has deteriorated;
  • in one.compressor devices. the switching valve from one circuit to another broke.

Increased noise during operation.

If the Beko refrigerator is noisy when working, then the most likely cause of the breakdown is the wrong installation or twisted transport bolts.

To eliminate the deficiency, make sure that the refrigerator is firmly on all legs, set in level, does not rest against the wall, and the bolts fixing the engine during transportation are released or completely removed.

In order not to encounter such problems, you can contact our company for installing the Beko refrigerator, in addition, we are engaged in the repair of Beko refrigerators, it does this quickly and efficiently, thanks to many years of experience with this brand and not only with it.

It’s time to order repairs!

Just call our master. He will advise you, answer all the questions that have arisen, tell you what kind of breakdown can be and how much its repair will cost!

BEKO NRF 5050s refrigerator device

The cooling system scheme is shown in Figure 1. The refrigerant circulation is carried out using a compressor with a capacity of 195 kcal/h. The compressor is equipped with an oil coil. There are two refrigerators in the refrigerator, one of which is located under the refrigerator. The water formed during thawing flows into the lower capacitor and evaporates there. A fan is located next to the compressor, which creates an air flow passing along the rear surface of the refrigerator and provides heat removal from the main capacitor. The refrigerator uses a cellular type evaporator. The compressor refrigerant enters the pipeline section laid in the walls along the door hole, which prevents the formation of condensate on the inner surface of the refrigerator. After that, the refrigerant enters the oil coil, then to the lower capacitor and in the main capacitor.

Increased noise during operation.

If the Beko refrigerator is noisy when working, then the most likely cause of the breakdown is the wrong installation or twisted transport bolts.

To eliminate the deficiency, make sure that the refrigerator is firmly on all legs, set in level, does not rest against the wall, and the bolts fixing the engine during transportation are released or completely removed.

In order not to encounter such problems, you can contact our company for installing the Beko refrigerator, in addition, we are engaged in the repair of Beko refrigerators, it does this quickly and efficiently, thanks to many years of experience with this brand and not only with it.

About the author

| Denial of responsibility | Contacts |RSS