Bosch refrigerator began to freeze a lot

What to do if the refrigerator is very freezing?

If you began to notice that the refrigerator is badly freezed, it is not necessary to immediately call the household appliances repair master. Most of the reasons for this problem can be handled independently, without even having special technical knowledge.

Modern technique is quite reliable and is seriously rarely broke. Typically, the causes of enhanced co.formation lie in the improper operation of refrigeration equipment. To return the refrigerator to normal operation, it is often enough to carry out minimal maintenance.

The reasons why the refrigerator is very freezing

The fact that the refrigerator is rewriting, you can guess when you see ice on the walls of the refrigerator compartment. Normally this should not be. Usually moisture from products when evaporating settles on the rear wall of the compartment. During the compressor operation, it freezes under the influence of cold air, and when the unit stops, it melts and drains along a specially equipped drainage system into a container installed in the rear of the device.

If the normal temperature regime is disturbed, moisture does not have time to go to the drainage canal and intends on the walls of the chamber.

Most often this is due to improper operation of the device:

  • You refrigerate the container with hot food, which leads to excessive condensation;
  • You often and for a long time hold the door of the refrigerator open, which forces the compressor to work continuously and escalate excess cold;
  • You store in a liquid chamber without lids or put in a vegetable box washed but not dried products, which leads to excess condensate;
  • You do not follow the purity of the drainage system, because of which moisture does not have time to leave the camera;
  • You set in the settings too low temperature, or super-cooker.
bosch, refrigerator, began, freeze

To return the device to good condition, you need to conduct a small maintenance. Namely. defrost the cameras, clean the drainage hole and make sure the correctness of the settings. First of all, check the position of the thermostat. It is considered optimal if it is put to values ​​2.5-3. But if hot weather is on the street, a given temperature may not be enough for normal cooling of products on the shelves and in the freezer, and the switch is transferred to higher values. With a change of weather, it is so easy to forget to put it back! Also check if the emergency frost button is pressed. It is easy to activate it by accident, wiping the panel.

Install the temperature regulator in the optimal position, then defrost the refrigerator-you need to somehow get rid of the already intended ice. When the chambers are completely hidden and dried out, check the drainage system. The drainage hole is located on the rear wall of the general compartment, in the lower part. It can be clogged with mucus and small garbage. Usually a plastic probe is attached to the device for its cleaning. But if it is not, you can push the plug in the drain channel with a thin wire or a ruff for cleaning the tube.

Eliminating the blockage, rinse the channel with warm water from a sprint or syringe. Make sure water flows freely into a container mounted on the back wall outside your unit. If everything is in order, you can turn on the refrigerator and load products into it in accordance with the operating rules. Watch the operation of equipment during the day, during which time it will be clear whether it was possible to eliminate the problem.

Bosch Fridge Freezers with Superfreeze | ao.com

Why is the refrigerator a lot of freezing?

In this article you will find out what to do if the refrigerator freezes a lot. We have provided the most common causes of this breakdown. If you have a column broken, then you can read how to carry out the repair of the columns.

The most common cause of severe frost of the refrigerator is the wrong position of the thermostat. You will need to inspect your device and if it is set incorrectly, then you should set the temperature regime less. This moment must be checked in the first place, since it is the easiest to eliminate. If you have a refrigerator with a switch, then it needs to be installed in position from 2 to 3.5. If your house has a new device that has a dial, then it is necessary to set the temperature within 4 or 6 degrees.

It’s important to know! New models of the refrigerator can have a super.commercial button. If you have it, then you should check if it is turned on.

Damage to the door seal

To the second malfunction, due to which the refrigerator chamber does not freeze products, you can include damage to the door seal. A sign that this problem you will have a constant puddle near its door. At this time, snow will begin to form inside the refrigerator, due to which products can freeze. You can replace the seal yourself. Here is a video that will help to deal with this issue in detail.

If you have not yet learned why the refrigerator is very freezing, then you should go to the third point of solving the problem.

Features of diagnosis

During the diagnosis of the refrigerator, the first thing you should check the most common causes. Then, after their exception, it is worth moving on to the rest. In order to make it easier, you can use one simple observation. It is worth paying attention to whether the refrigerator freezes is strongly freezing or, conversely, quite weakly. Depending on this, some breakdowns can be immediately excluded.If the frost is strongly and does not turn off, then it can be the on frost mode (supermorous). If the matter is not in it, then the next step is to check the compressor and thermostat.

It is interesting! What temperature should be in the refrigerator. basic information

The compressor usually “sticks” the relay. When typing, the compressor does not turn off, since the contacts have clipped and do not open the circuit.

When breaking the thermostat, the sensor is faulty. It does not transmit the signal, so the relay contacts do not open the circuit. Violations of control on modern refrigerators lead to the same consequences. Here is also a team to turn off the relay is not transmitted from the sensor.

If the device does not freeze much, but without stopping, then the case may be in the rubber seal on the door or leakage of the refrigerant. In the latter case, the compressor has to constantly escalate the freon to set the specified temperature values. It is obviously impossible to do because of the leak, so the engine works continuously.

The refrigerator No Frost is badly freezing. what to do

The peculiarity of the No Frost system from other types of refrigerators is the location of the evaporator outside the freezer, behind the rear wall of the unit.

The fan, which is located near the evaporator, supplies chilled air inside the chambers through the system of air channels.

The accumulated condensate is removed from the tubes as a result of their heating, after which melt water flows through drainage tubes.

Violation of the thawing process leads to icing the evaporator and fan blades, as a result of which the heat transfer in the device decreases, and the refrigerator begins to freeze too intensively.

The reason for this phenomenon may be a breakdown of a heating element, a heating tube, or a block of drain channels. In the first case, it is necessary to replace the faulty device, in the second. clean the drainage system.

Bosch refrigerator is badly freezing

Everything is good in moderation, is it not true? This expression fully applies to the refrigerator Bosch. If your kitchen assistant begins to freeze too much, this indicates violations in his work.

The most banal reason is that they chose the temperature regime incorrectly. Perhaps you accidentally put the toggle switch to the maximum.

Often the reason for the too strong operation of the unit is the wear of the seal. The unit begins to freeze harder to compensate for the temperature difference.

Another possible malfunction. a drainage hole is clogged or the capillary system clogged.

The thermostat or the air sensor stopped his work.

The switching valve can also break.

NOTE! depend on the complexity of the work. The are indicated only for work without taking into account the cost of spare parts and consumables.

Malfunctional lodge bosch cost of repairing costs for replacement
Replacing the door seal from 1400
Cleaning the capillary system from 1900
Repair or replacement of the heat.controller (temperature sensor) from 500 from 1200
Replacing the electromagnetic valve from 1250

NOTE! The final cost is set after the diagnosis of a malfunction by a specialist. Diagnostics is carried out free of charge, but in case of refusal of repair, it is necessary to pay 400 for the departure of the master.

Elimination of a malfunction: repair or replacement of causal part, setting up equipment and electronics;

If you find that the Bosch refrigerator is badly freezed, it’s time to call the master. Remember that independent attempts to repair the unit can lead to even greater damage. Masters of the company “SKVIS” have special skills and many years of experience that help them successfully cope even with the most difficult breakdowns. Contact us! And your refrigerator will last for many more years!

NEFF refrigerator is badly freezing

Everything is good in moderation, is it not true? This expression fully applies to the refrigerator NEFF. If your kitchen assistant begins to freeze too much, this indicates violations in his work.

The most banal reason is that they chose the temperature regime incorrectly. Perhaps you accidentally put the toggle switch to the maximum.

Often the reason for the too strong operation of the unit is the wear of the seal. The unit begins to freeze harder to compensate for the temperature difference.

Another possible malfunction. a drainage hole is clogged or the capillary system clogged.

The thermostat or the air sensor stopped his work.

The switching valve can also break.

NOTE! depend on the complexity of the work. The are indicated only for work without taking into account the cost of spare parts and consumables.

NEFF loser of the cost of repair work costs for replacement
Replacing the door seal from 1400
Cleaning the capillary system from 1900
Repair or replacement of the heat.controller (temperature sensor) from 500 from 1200
Replacing the electromagnetic valve from 1250

NOTE! The final cost is set after the diagnosis of a malfunction by a specialist. Diagnostics is carried out free of charge, but in case of refusal of repair, it is necessary to pay 400 for the departure of the master.

Elimination of a malfunction: repair or replacement of causal part, setting up equipment and electronics;

If you find that the NEFF refrigerator is badly freezed, it’s time to call the master. Remember that independent attempts to repair the unit can lead to even greater damage. Masters of the company “SKVIS” have special skills and many years of experience that help them successfully cope even with the most difficult breakdowns. Contact us! And your refrigerator will last for many more years!

The refrigerator Atlant does not freeze

The production and repair of refrigerated atlant of compression type units differ in significant technological complexity, but compared with the repair of other electrical products. The complexity of the production and repair of such units is explained by the need for thorough dehydration of all materials, parts and products included in the airtight system of the unit, ensure reliable sealing, removal of air from the unit, etc. It should be borne in mind that it is much more difficult to effectively perform some technological operations in the conditions of repair than in the conditions of production (for example, the unit drill).

You can disassemble and collect sealed units only with welding and soldering. Therefore, all previous operations must be performed highly, so as not to be injected in the plowing and cutting of the unit to correct it.

  • Moisture in the system.
  • Filter filter.
  • Clogging of the capillary tube.
  • Frequent operation of thermal relay.
  • Refrigerant leak.
  • The evaporator is mechanically damaged.

Debugg:

The appearance in the moisture system leads to freezing and clogging of the capillary tube. This moisture, freezing under the influence of low temperature, creates an ice cork, which is formed, as a rule, in the place where the capillary is connected to the evaporator pipe. This is facilitated by a low level of solubility of water in the refrigeue, as well as a small diameter of the most capillary tube. At the site of the capillary exit into the pipe there are constant conditions of low temperature and low pressure, so the capillary blockage can occur even with moisture in a small amount.

This malfunction can be determined as follows: heated the end of the capillary tube at the place of its connection with the vapor pipe, while the hiss of the freon passing into the evaporator should be heard. Then the noise when working the refrigerator will stop.

It is possible to avoid freezing of the capillary tube primarily due to high.quality drying of the refrigeration unit, which should be carried out during its factory assembly and repair. The quality of the refrigerated and oil, which fill the refrigerator, also are of great importance. However, even if drying was carried out correctly, moisture may appear as a result of the decay of an intermediate oxidation product as a result of the refrigerator. During the long.term operation of the refrigeration unit, the stator windings inevitably overheat. As a result of a systematic overheating, insulation of windings is charred and partially destroyed. Substances that are destroyed are organic and moisture is released when they are charred. When repairing the refrigerator, along with the measures taken by the drying of the shade, oil, as well as all the details of the refrigerator, the use of a special substance that can actively connect the water that appears in the refrigerant is advisable before assembling the unit.

Filter or filterer. Heating the surface of the filter or filter.drying cartridge connecting the capacitor coil with a capillary tube should be the same as heating the last turn of the capacitor snake.

The temperature of their surfaces the same to the touch will indicate the normal passage of the freon through the filter without throttle. In the case of a partial clogging of the filter, the surface of the filter housing (filterer) at the site of the spa with a capillary tube will be noticeably colder.

No cold in the refrigerator is caused by clogging (blockage) of the capillary tube. On the capillary tube, a liquid freon enters the capacitor to the evaporator. When circulating a freon according to the system in the capillary on the walls of the capillary, deposits form, something like paraffin, which partially or completely close the passage hole of the capillary tube, while there is still enough pressure of the freezer, and there is no longer for the refrigerator.

There are many opinions, with what methods you can deal with this. Puning the capillary using a high pressure pump. to eliminate the defect with qualitatively and for a long time is almost impossible, t.to. Capillary blockage occurs due to a raid along the entire length of the tube, and not because of the sandstone, which was stuck somewhere at the exit (it could be possible and it would be possible to sell it).

Although the capillary tube is not a separate spare part for the refrigerator, but as it were, it is part of the evaporator, however, its replacement is possible and is the most effective and reliable way of repair. Replacing the capillary tube is 100%effective, which is recommended to make the manufacturer in case of clogging.

Whirlpool Refrigerator Diagnostic. Freezer Is Cold but Is Not Freezing. GS6SHAXMS00

Launching relay. Violation of the integrity of the starting relay is the cause of the unstable operation of the refrigerator. As a rule, a launch vehicle is out of order due to deterioration, but sometimes a malfunction is a consequence of the factory marriage that has appeared over time. This problem is eliminated by replacing a faulty part. A sign of improper relay triggering is a weak buzz when turned on, frequent shutdown and turning on the refrigerator, sometimes thawing the evaporator. To eliminate this malfunction, it is necessary to check the voltage and making sure that there is no drop or increase in voltage, check the relay mount. With normal voltage, it is necessary to remove the relay, disconnecting it, and then turn on the electric motor directly. If the engine works, put a new relay. In this case, the refrigerator should work normally. Otherwise, it is necessary to measure the power of the electric motor and current strength.

Refrigerator Freezing Food, Easy Repair, Save Money

To verify the launcher relay, it is necessary to remove the lid. In some old models of domestic refrigerators, it is attached with latches, which can simply bend. Pay attention to the scheme of a launcher.protective relay, usually they are all arranged according to a single principle. The main breakdown is the jamming of the core in the coil, the springs, the breakdown of the rod or the burning (oxidation) of the contact schemes.

Remove the coil, remove the contacts with the rod and wipe the device thoroughly with a soft cloth with alcohol. Working contacts must be cleaned with emery, it is also useful to clean the stem so that it is freely placed in the coil channel. If the rod breaks down, then it can be replaced by home.made from a 2.5x35mm nail, they stay even longer than conventional plastic rods. Do not forget to only clarify the size of the rod for your refrigerator model. After checking, collect the relay back and connect the wires.

The refrigerator No Frost is badly freezing. what to do?

It should be checked whether the function of the super-carbonation is turned on, in which cooling works in uninterrupted mode. There are such buttons in modern models, and if someone accidentally turned it on, then the unit will freeze the contents of the refrigerator too much.

This reason for the incorrect work of the household appliance is not difficult to identify and eliminate on its own. It is more reasonable to instruct professionals to solve more difficult problems. for example, repairing refrigerators in the Volzhsky district, we produce at affordable and with a guarantee of quality work.

What else could happen to your home factory of cold? It happens that in the unit No Frost in the refrigerator compartment a snow.coat is formed, and the products freeze. At the same time, in the freezer, everything stucks, a lot of non.freezing water and ice accumulates.

The fact is that the elastic band that seals the refrigerator door wears out over time and passes warm air inside. The unit has to freeze more intensively than usual. If you do not urgently change the seal, the compressor can break and then only specialists can return it to life.

How to make sure the alarm in your Bosch fridge doesn’t go off

The refrigerator No Frost is badly freezing. what to do

The peculiarity of the No Frost system from other types of refrigerators is the location of the evaporator outside the freezer, behind the rear wall of the unit.

The fan, which is located near the evaporator, supplies chilled air inside the chambers through the system of air channels.

The accumulated condensate is removed from the tubes as a result of their heating, after which melt water flows through drainage tubes.

Violation of the thawing process leads to icing the evaporator and fan blades, as a result of which the heat transfer in the device decreases, and the refrigerator begins to freeze too intensively.

The reason for this phenomenon may be a breakdown of a heating element, a heating tube, or a block of drain channels. In the first case, it is necessary to replace the faulty device, in the second. clean the drainage system.

Bottom line and diagnostic guide

We will summarize all the cases why the cooling system does not work and their description. The table can be used as a kind of guide, which is enough for preliminary diagnosis of breakdowns.

bosch, refrigerator, began, freeze
  • no pressure for circulation;
  • compressor wear;
  • Freon leak. The breakdown more often lies in the steel contours of the perimeter of the freezer, in the nodes and places of connection of evaporators;
  • faulty thermostat, sensors, (controller) turn off cooling earlier than required;
  • The motor does not turn off and after defrosting the unit does not work. Freon leak.

Characteristic breakdowns of models with nofrost

Among users, a complete noufrost is popular, in which the refrigerator does not need to be defrosted (this is required to be done very rarely for prevention. once a year). With nofrost, the refrigerator is cooled by a cold stream, a fan, and the heating element periodically heats the evaporator in the freezer so that it thaws.

  • The thaw broke, the evaporator was covered with ice, which reduced its performance, respectively, the temperature increased;
  • For the same reason, the channels for circulation of cold air in the refrigerator compartment were riddled. there the temperature also rises there.
bosch, refrigerator, began, freeze

Features of two.compressor refrigerators

The compressor is the main functional element, a motor with a container with a refrigerant. Two.compressor refrigerators are more reliable, since the load on each motor and vessel with freon is significantly reduced. After all, breakdowns, although much less often, are observed. Problems similar to the described, but it must be borne in mind that each camera has its own refrigerator circuit with the indicated elements. The malfunction in one department does not affect the work of the second.

What can be done by yourself

Trifling problems are not excluded. Options that can be fixed yourself:

  • Check the settings for erroneous exposure of high/underestimated temperatures. Often, the upper chamber does not freeze in the refrigerator, precisely because of the improper tuning, especially if the product is new and just connected;
  • Two.compressor models have an option of a separate shutdown of cameras. perhaps one of them is accidentally deactivated;
  • A single failure is possible. it is necessary to defrost and start the unit again;
  • Doors skew, incorrect position of the loops: from wear, when outweighing. It is necessary to check and bring these elements to the correct position (tighten the bolts, fastening, etc.);
  • Skorus and breakdown may appear due to improper adjustment of the legs-despite the apparent insignificance, this factor is extremely important, as it affects the entire system. Causes not only loose fit and leakage of cold, but also incorrect movement of streams, refrigerant, rattling;
  • In most cases, you can replace the seal yourself by buying it in a special store.

Actions of specialists in the repair of the refrigerator

Refrigerators are complex for independent repair: without experience, special studies, knowledge of the specifics of details, the unit is unlikely to be repaired. In most cases, there is only one way out. calling the master.

What does the master do when repairing refrigerators:

  • replacement of the compressor, thermal attempt, thermostat, electromagnetic valve, filter-dryer;
  • dismantling the old and a hitch of a new evaporator;
  • determination and sealing of a leakage place (in this case, the heating circuit can be cut for connecting the tubes directly);
  • updating, repairing the elements of the thaw, fan, heating element;
  • installation of a new motor;
  • pushing the blockage in the capillary tube with a special jack or its complete replacement;
  • installation of new seals, loops on the doors;
  • replacement of capacitors, other elements on the boards and in the control unit. Burnt, driving tracks, contacts are broken. If the breakdown is significant or the processor is out of order, a new BU is installed.

In the process of repair, a cold circuit, vacuuming the system, refueling it with freon is underway. At the same time, sealing is carried out, so the skills of soldering copper and other high.gloves of metals are required.

About the author

| Denial of responsibility | Contacts |RSS