Electrical diagram of the juicer
The wiring diagrams of most types of juicers do not differ in principle. Only an electronic mode control unit can be added.
Power is supplied via a C6-type plug with a flexible cord. Capacitor C1 serves to suppress interference emitted by the brush motor assembly. Resistor R1 serves to discharge the capacitor C1 after disconnecting the plug from the socket to prevent human current shock when touching the pins of the plug. These elements may not be present in budget models of juicers.
Selection of the juicer operation modes is carried out with the switch S1. In the position shown in the diagram the juicer is switched off. When moving the switch handle one position to the right, its movable contact closes the pins 1-2 and the supply voltage through the rectifier diode VD1 flows to the motor, denoted in the diagram by the letter M. Diode does not pass half of the AC sinusoidal current and thus reduces the rotation speed of the grater-sieve by half.
When moving the motor one step further, the contacts 1-2-3 are closed, and all the mains voltage is applied to the motor winding, and the juicer runs at full power.
The Sble limit switch is used to prevent the juicer from being switched on when the top cover is removed and has the task of protecting people from injury. It is mechanically connected to the lid and if the lid is not fitted the switch is open.
To reduce the wear and tear of the motor brush-collector assembly and suppress radio interference, there are spark-quenching capacitors C2-C3. Inductance coils (chokes) are often also installed in the motor power supply circuit for better radio interference suppression.
To protect the motor from overheating during continuous operation (more than 15 minutes), serves element of thermal protection St, which opens circuit of supply voltage.
There may also be a connection indicator in the circuit. Usually it is a miniature neon light bulb, included through a resistor to the power supply wires.
All grinders are divided into two types according to the grinding method: millstones and with a rotary screw. Also differentiate between manual and electric, but the latter are firmly and thoroughly squeezed their mechanical counterparts.
What a rotary electric coffee grinder consists of:
This is the way both expensive and cheap models are designed: “Bosch”, “Mikma”. Soviet electric coffee grinders were assembled in the same way.
To disassemble them, you need to perform the following steps:
- Remove the lid.
- Disconnect the bottom. In Soviet devices it is fixed with Phillips screwdriver screws, in modern devices it is usually just lifted up and removed.
- In the center, use a screwdriver to squeeze the set screw.
- Carefully unscrew the rotary screw (in the same direction as it grinds the coffee) with your hand or narrow pliers.
- Remove the screw and bowl.
- Remove the main body.
Important Before you disassemble the grinder, always disconnect it from the power supply.
Grain grinders in general follow the same principle.
- Use a screwdriver to pry out and remove all the turntables.
- In the same way detach the bottom (it is desirable to hit the 4 locking teeth).
- Undo the 4 self-tapping screws around the perimeter and remove the top part.
- Remove the coffee pot.
- Use a spoon to remove the rest of the kernels, and then use a vacuum cleaner.
- Dismantle the disc regulating the grinding (rotating it clockwise).
- Remove the upper fixed millstones blade.
- For further cleaning. remove cushioning springs.
Depending on the model and brand, the algorithm will be slightly different, the magazine “Miss Clean” recommends focusing on the instructions for the specific model.
Соковыжималка Clatronic 2758 AE. 3D-обзор от Elmir.ua
How to disassemble the juicer
Owners of juicers often wonder how to disassemble this kitchen unit correctly t. е. without compromising its functionality. The need for disassembly appears when there is a disturbance in the normal functioning of the device, because some faults can be repaired by yourself, thus saving the budget.
Review: Juicer Clatronic AE 2758. Will do for lack of anything better
All the apple trees are covered with fruit, which have already begun to fall down.But back to the subject of the review.The juicer is not big at all, it’s compact.
It is made entirely of plastic. Except for the internal parts, of course. Do not know whether to attribute this to the pluses or not.The technical specifications are on the bottom. I can not find the box and instructions from the juicer, somewhere all is gone. It is the power that counts. 400 W. We do not know where the juicer is made, but it is written in German.
It disassembles easily and simply into a few parts. That should be done after use, to wash it.
Controls are also simple. On the bottom of the button: on and off.
Beforehand, of course, it is necessary to connect the plug to the socket. The cord is long, and the plug is without grounding, for plastic devices, you don’t need it.
Now let’s try to squeeze juice from these apples
It is necessary to cut them beforehand and remove unnecessary things.
The juicer is easy to use. You put the pieces of apples inside, turn it on and push it through.
The whole process takes just a few minutes. The juice is ready now.
To say that I was not fully satisfied with the result, in the waste a lot of whole pieces of apples remained.And this is how the juicer itself looks after work. It’s not hard to clean. But it’s better to do it right away.
What can I say in the end. All in all, satisfied. The process is quick and easy. The result is good, though there is some waste. But they can also be used for further processing, for example, to make apple puree.
Components of the Bosch MES Juicer
Fortunately for owners of this type of device from this well-known manufacturer, disassembly of the appliance for repair will be required on very rare occasions. A different thing is the everyday disassembly after juicing, which any hostess or owner should learn to do quickly and even automatically.
This is the case with the Bosch MES series, by the way: the first time you may have to flip through the instructions to get it right. But then cleaning and washing the juicer will go quickly and almost “on autopilot”.
Before starting work, carefully inspect the appliance. It tentatively consists of the following parts:
- switch with three positions: open. designed to unlock the lid; off. off state; on or 1. on state;
- motor unit, which has a compartment for the cord from the power supply. depending on the model is made of plastic (most often) or stainless steel;
- The container where the waste products (cake) are collected. is made mainly of plastic in different shades;
- strainer made of stainless steel, less often. of plastic;
- The insert under the strainer is made of plastic in the color of the body;
- The lid with a shade of the main color of the model;
- The loading insert made of transparent polymer;
- transparent plastic pusher;
- Capacity for storing the finished juice, equal to one liter, with a special compartment for foam, made of transparent plastic under the color of the body;
- legs made of food-safe rubber.
Disassembling the juicer ourselves
Most malfunctions of this type of kitchen equipment, in one way or another, are related to the electric motor or moving parts, such as gears, clutches. If you have not done with the juicer anything from which it is guaranteed to fail (dropped, for example), it is possible that you can repair the damage yourself. But to do this, you will first have to carefully inspect the device from all sides to understand how you can disassemble, and most importantly, how to put the juicer back together.
Repair of the coffee machine with their own hands problems, disassemble by themselves.
Repairing the coffee machine with your own hands problems, disassemble by yourself.
The coffee maker makes delicious coffee only when it works properly. Some problems in operation may not affect the operation of the device itself, but will always affect the taste of the finished drink. There are a number of malfunctions of the coffee maker that can be repaired yourself, without going to a service center.
Where to start an independent repair
As in other cases, when repairing a coffee maker, it is important to first identify the problem. The most unexpected malfunctions are possible with regular use. Therefore, before fixing the problem, the coffee maker must be unplugged, making sure there is no hot water in the tank.
Possible manifestations of problems
Hot water, even if it is filtered, still leaves mineral deposits on parts of the coffee machine. The more of them, the more it affects the taste of the finished drink. To get rid of this malfunction and prevent its occurrence, the device should be cleaned once a month. The appliance can be cleaned with a special decalcifying agent. Of effective home remedies, experts recommend using acetic acid.
Important! Sometimes the taste of coffee changes, not because of malfunctioning of the coffee maker, but because of improper storage of the product. Coffee must not be stored open or allowed to come into contact with other foods. After all, grains are excellent at absorbing other flavors and smells.
Sometimes very little or no water flows out of the appliance. The most common reason for this is a clogging of one of the tubes. Aluminum heating tubes tend to clog most often. Vinegar must be run through the coffee maker to fix the problem (no filters, no coffee). Flushing is done several times until the water flows in the right amount. After cleaning, flush the pipes several times with clean water (do not put any filters or coffee in yet).
Many modern devices have a function to control the amount of brewed coffee. This is a useful feature, so you can not only make yourself a cup of drink for the morning, but take some of it with you in a thermos. Therefore, if there is a function, it is necessary to check its settings. Also check the amount of water in the tank. For the correct adjustment you can use the manual to the device, where everything is described in detail.
The problem in such a situation is related to the heating element. It will be necessary to find a spare part to replace the coil. Such a repair process involves interfering with the internal structure of the coffee maker. Therefore, if there is no skill in such work, it may not be worthwhile to engage in self-replacement.
How to disassemble the coffee maker yourself
When there is confidence in your abilities, you can try to disassemble the coffee maker and repair it yourself. It is important to remember that before starting the process, it is necessary to disconnect the appliance from the power supply. Do not open the device at any breakage, otherwise, the final repair by a specialist will be more expensive.
It is necessary to unscrew the screws on the outside of the housing. They are usually on the back of the appliance and can be removed with a screwdriver;
There are screws that have no edges and look like cones. They unscrew using pliers (back you can twist the usual screws under the screwdriver-cross);
If there are latches in the housing, they must be opened. This is done with a long screwdriver. Usually these latches are on the bottom side of the coffee maker;
When the case is opened, you can begin to determine the fault. Replacement parts for imported appliances are readily available. Most likely, you will still need to go to a service center for them;
Sometimes ground coffee gets into the gears of the electric motor and triggers protection. To clean the coffee maker, you need to turn it over, unscrew the screws and remove the bottom cover. Then vacuum everything out, lubricate with solidol.
When there are doubts that fixing it yourself will lead to a positive result, it is better not to risk. Many service centers refuse to repair a device that was previously disassembled at home.
Juicer repair with their own hands
The basis of the juicer is the motor. Today, asynchronous, collector electric motors are used. No wonder. no other technique knows. Actually, the repair of juicers with their own hands often faces the situation of a failed motor. To replace the mechanical part is almost impossible, the devices, working on the basis of meat grinders, when getting a bone break the sockets, plastic bushings, hydraulic presses have a lot of fuss with the oil system. Consider the issues, do not expect a detailed guide, but the main types of faults will be considered sufficiently.
Clatronic tests
Test of the CLATRONIC FS 3261
Such a packer is suitable for packing a large number of products into smaller portions, for packing products intended for deep freezing to protect them from freezing, for simple hermetic packaging without evacuating air.
Ice cream maker test. Thick and sweet, eaten without residue!
The variety of sorts of ice cream presently on the shelves cannot satisfy the demanding taste of demanding Russian consumers. After all, children love ice cream so much and we want to give them the best. And the various “E’s” that are included in the desserts on sale are not trustworthy. That’s why many people start making their own ice cream at home.
The Clatronic ICM 3225 ice cream maker test
This ice cream maker has two features: large capacity and a timer with automatic shutoff. The bowl is quite large and wide, but thanks to the standard height it fits easily enough in the freezer. Advantages: big volume of the received portion, automatic control, affordability. Disadvantages: ice cream needs to be “hardened” in the freezer. Few recipes in the instructions.
