Connection of the Washing Machine Machine

Beko washing machines device

Bucky washing machines are made of special plastic (polypropylene). The cover is made of the same material, which is attached to the tank on the clamps. The electric motor is attached to the tank on bolts with rubber bushings. In the back of the tank (left, right and above), nests for transportation bolts are made. On top of the tank and under it there are two concrete counterweights. The tank and the nodes attached to it are suspended to the case of the machine on two springs located on the sides. There are two shock absorbers at the bottom. The drum is made of stainless steel.

Rice. 1 main nodes and components of the washing machines Beko (side view).

Types of electric engines

Electric engine is a machine operating from electricity, moving various elements using the drive. Produce asynchronous and synchronous units.

Synchronous engine

From the school bench, it was established that during mutual approximation, the magnets are attracted or repelled. The first case appears in multi-dimensional magnetic poles, the 2nd-in the same name. The conversation is about stable magnets and a magnetic field constantly organized by them.

In addition to the presented, there are unstable magnets. All, without exception, remember an example from the textbook: the figure shows a magnet in the form of a conventional horseshoe. A frame made in the form of horseshoe with half rings is placed between its poles. The current was supplied to the frame.

Since the magnet rejects the same name and attracts different poles, an electromagnetic field appears around this frame, which unfolds it in an upright position. As a result, it applies to the main case for the symbol of the current. Modified polarity turns the frame and again gives to the horizontal area. The work of the synchronous electric motor is formed and formed and formed.

In this scheme, the current is fed to the rotor winding represented by the frame. The source that creates an electromagnetic field is considered to be windings. The stator carries out the functions of the magnet. In addition, it is made of windings or from a set of stable magnets.

The speed of rotation of the rotor of such an electric motor is the same as that of the current, which is fed to the winding terminals, t. E. They work at the same time, which gave the name to the electric motor.

Asynchronous apparatus

To deal with the principle of operation, we recall the picture: the frame (but without a half) is located between the magnetic poles. The magnet is made in the form of a horseshoe, the ends of which are combined.

We begin to slowly twist it around the frame, watching what is happening. Until some point of movement, the frame is not observed. Further, with a specific angle of rotation of the magnet, it begins to spin behind it with a speed less than the pace of the last. They do not work at the same time, so the motors are called asynchronous.

In this Magnet electric motor, this is the placed electric refinement in the stator grooves, in which the electric. The rotor is considered a frame. In its grooves there are accurately connected plates. It is called that. Short.Closed.

Differences in electric motors

Outwardly the motors are difficult to recognize. Their main difference is the rule of work. They also vary in the scope of use: synchronous are more complex in design, used to act as equipped such as pumps, compressor, etc., t. E. Working with constant speed.

In asynchronous, during an increase in overload, the frequency of verification decreases. A huge number of devices are supplied with them.

Beko WB 6110 SE and XE Instructions, operating the washing machine in Russian: Download

Look for the instructions of the Beko WB 6110 SE washing machine ?

We have saved all the Russian instructions in the language you need and you can read them right on this page or download yourself and print the necessary page.

In the Комментарии и мнения владельцев you can ask your question to the master, or share the solution to your problem with other readers of our portal.

Detailed instructions of the Beko washing machine will help you solve issues with the technical characteristics of this machine, how many linen can be loaded into this washing machine, how much and where to pour powder for washing, as well as installation and connection, as well as how to use the module of the washing machine control.

Instructions for using the Beko WB 6110 SE washing machine

We also made a link for you, by which you can download this instruction for a computer for a computer for free

If you adhere to recommendations from this article on the use of a washing machine, then certainly increase its life, and also enjoy washing and using this home assistant!

How to remove the engine from a washing machine

Electric motor. One of the central links of any washing machine. He is responsible for the turnover of the drum during washing, rinsing and spinning. If the engine stops working, then washing will not begin. Therefore, many users are worried about whether it is possible to remove the engine of the washing machine with their own hands to repair or replace it?

If you already have the skills of repairing household appliances, then disassembling the washing machine will not seem to you something difficult. The main thing is to take into account the type of washing machine, since the engines in this technique can stand different: asynchronous engine without brushes, ordinary collector or direct drive engine.

In this article you will find instructions for dismantling the motor with photos and videos.

Why remove the engine

In modern washing machines, manufacturers install inverter engines, evaluating their performance at 10-15 years old. Therefore, such electric motors break extremely rarely. So, you have a cm with a traditional collector engine.

Usually these engines suffer from such breakdowns:

In order to convince 100% in the nature of the breakdown, it is necessary to remove the electric motor and check it. It is important to do it right so that you will not harm the machine anymore.

Important! The lion’s share of all the breakdowns of the motor falls on the brushes. Less commonly, there are problems with the winding, and only occasionally the problem concerns the lamella.

How to remove the motor

To remove the engine from the washing machine, it is worth observing a clear procedure, stock up with the necessary tool and conduct a photo or video. This is necessary to capture the location of the wires and then collect everything back without problems.

How to change the motor? Follow the instructions:

• Remove the rear panel (for Indusite brands, Ariston, Candy, Zanussi, Electriclux) or the front panel (in Bosch washing, Siemsung, Samsung, LG or Beko). The back panel is held by several mounts. To dismantle the front panel, you need to remove the control panel, the top cover and the base panel. Read more on the pages: “How to disassemble the LG washing machine” and “How to disassemble the Bosch washing machine”.
• Under the tank you will see a motor that is held in four seats. To two of them the engine is attached with screws. Before taking off the mounts, disconnect the drive belt, and also remove the supply and grounding wires.
• Now proceed to unscrew the mounts. In most models, the wrench for 13 copes with these purposes.
• After they are removed, pick them up with a thin screwdriver in the places of attaching the engine to the tank. Often these places are stuck, therefore, to remove the motor, efforts will be required.
• After the motor succumbs, pull it to you and remove it from the machine.

Now you can repair the engine (see the article “How to replace the engine brushes in the washing machine”) or mount a new.

To change the electric motor for a new one, buy a pre.Original analogue and install it in the reverse order by correctly connecting all the wires. After assembling the washing machine, start a test washing to make sure of your actions correctly.

How to eliminate refusals

We will figure out how to repair the Beko washing machines on our own.

You should know that after washing on a typewriter, waste water does not differ in cleanliness and transparency. So that various small garbage and dirt are not clogged, a special filter is installed in front of it, which in most cases is clogged. The main task is to find this element, which is usually located in the lower part of the machine, under a small hatch or panel.

Further, actions should take place in the following sequence:

• Before extracting the filter, a pelvis is put on the floor or a rag is spread to collect the spent water, which necessarily pours from the hole. Some models of cars in the kit have a hose for emergency water descent,
• In order to extract the filter, it should be handed over to the right side,
• After that, the filter is cleaned and washed under a stream of water,
• Using a screwdriver, you can clean the pipe that can also be clogged,
• For preventive purposes, it is possible to clean the filter installed on the water fence (it is located at the fastening point of the fence hose to the rear wall). As a rule, particles of rust and sand located in tap water accumulate in it,
• Having completed the cleaning filter, you should not rush to install it in the same place. You should examine the pump for draining itself. Quite often, machines with their own diagnostic system reveal the pump failure and give a signal about this. But sometimes, if the malfunctions are small (the impeller has gone through), the “controller” is not able to identify the problem,
• To check the pump, it is necessary to activate the water drain mode and look at the cork hole, how the impeller works. Rotation will say that everything is fine. In case of immobility of the element, it is necessary to clean or completely replace the drain pump,
• Now you can install everything in its place, assemble a machine and carry out a trial washing.

• Water is poorly heated.

To cope with such a refusal, you will have to again perform a partial disassembly of the washing apparatus. But first it should be noted that in all machines the thermoelectric generator is one of the weakest nodes. The people call it a simple word. Ten. Mineral components located in the pipes under the influence of hot water begin to crystallize and accumulate on the heater. The plaque does not allow the heat to go to the water, so the heater is burning out. But if the water in the pipes is soft, and the scale does not appear, or you use special products, then the heating water is still able to burn out, as it has its working resource.

In order to make sure what happened to the heating element, it is necessary to get to it. The peculiarity is that in different models it is located both in front and behind. For the first case of action, the following:

• The front panel of the machine is removed. But it is first necessary to remove the cuff from the door. You need to act carefully so as not to cause damage to it,
• Before you will stick out two contacts with the wiring supplied to them, which must be disconnected,
• Using a tester, you need to check the resistance. With the norm, its value will be from 25 to 30 Ohms. In other cases, we can confidently assume that Ten refused,
• We unscrew the nut from the bolt, holding the heating element under the drum, carefully pull out the heater,
• We clean the place for its installation from plaque and accumulated garbage,
• Install a new analogue, connect the wires.

In the event that the heating device is serviceable, you should check the temperature sensor located under the upper panel.

• Twist the screws and remove the top panel,
• The sensor is dismantled along with the tray for detergents and the control panel, since all this creates interference to get to the element of interest,
• Having opened access to the sensor, you must turn off all the wires from it,
• Check the resistance. Normally it should be 4.7 com,
• The sensor must be held in a container with warm water. The resistance indicator should decrease. Otherwise, the element must be replaced,
• The new sensor is installed in place, all work is performed in the reverse order.

• Do.It.Yourself electricians and electronics repair.

If you have special knowledge and the necessary experience in the repair of electrical appliances, then you can eliminate the contact of contact or oxidation of the terminal. All that is required is the circuit of the electrical wiring of the machine, which can be found in the operating instructions.

But with electronics not everything is so simple. Repair work or replacement of management fees implies special knowledge and certain experience. Taking into account the cost of a new module, you should not try to repair it yourself. In this case, it is better to invite a master who will do everything himself.

During the operation of the unit for washing things, in particular. During the execution of the spin, the machine gives out a strong vibration, begins to “jump” in different directions. Pay attention to how much linen is loaded. Vibration is possible if the maximum norm is exceeded. Another recommendation is to check how correctly the supporting legs of the. They are set in level so that the device does not stagger. Experts advise using special stands when installing a machine.

Installation of a washing machine

Consider connecting an automatic washing machine to communications. It is required to connect cold water to the highway and provide a separate drain for the release of spent water.

In the designs of most models of washing machines, the maximum and minimum height of the production pipe is limited and minimum. To connect with the sewer system of the apartment, an additional siphon can be installed or the end of the exhaust pipe can be fixed on board the sink or bathroom (rice.2).

Rice. 2 b Plum option in the bath.

The fixing should be reliable enough to exclude the flooding of the apartment when the drain hose falls to the floor.

The most modern is the inpatient connection of the drain system to the sewer. In necessary cases, the hoses can be increased, but the length of the drain hose is limited to the power of the drain pump. The maximum length of the drain hose is indicated in the documentation attached to the washing machine.

The drain hose is fixed on the rear wall of the machine at a height of about 80 cm.

The second end of the drain hose is connected to the sewer. To avoid an unpleasant odor from the sewage system, you should put a special siphon or bend the end of the hose so that a water mash is created.

Some books recommend a loose connection of a drain hose with sewage (rice.3).

The presence of an air gap at the site of the drain is proposed to avoid sucking water from the machine to the sewer and the possible “freezing” of the machine when performing some programs. But such a compound has one condition: the height of the air gap should be a few centimeters exceeding the height of the water lifting in the bathroom and the sink with a possible sewer clogging. Otherwise, it is likely to flood the apartment through a low air gap.

Existing types of electric motors

Modern washing machines are usually equipped with single.Phase electric motors with tachogenerators that regulate the number of revolutions. Soviet electric motors are already considered a rarity, they are distinguished by a two.Speed mode of operation. Motors installed in modern washing machines can be divided into three types. These are engines:

Asynchronous

In engines of this type, the rotor speed differs from the speed of the magnetic field of the stator winding. This is the most common type of electric motors. Asynchronous condenser engines are installed in washing machines, powered from a single.Phase household power supply.

There are two windings on the stature, one of which is included directly in the network, and the second winding is connected to the start.Up capacitor, forming the starting rotating magnetic field.

The plus of asynchronous engines is simplicity of design and unpretentiousness in maintenance. Wear.Resistant electric motors can work out with proper maintenance for more than one decade.

The disadvantages of asynchronous motors include sensitivity to the fluctuations of the network current frequency and the inability to change the speed of rotation of the shaft during operation, however, this does not interfere with the use of them in various home.Made devices.

Collector

Many washing machines today are equipped with collector engines. A distinctive feature that is the presence of 2 brushes. The brushes adjoin the rotor collector, telling him electricity, which makes the rotor rotate in the magnetic field of the stator winding. Collector power blocks are operated using a belt transmission of torque.

The pluses include the presence of a pulley of the pulley on the shaft, which facilitates the task of home masters in creating devices with belt transmission, the ability to work from direct current. As a rule, engines have small dimensions and are controlled by a simple electric circuit.

The disadvantage can be considered the rapid wear of the belt and the “ability” of brushes to fail at the most unexpected moment. And yet this can be calculated by minor trifles compared to the advantages.

Inverter

For the first time, the inverter engine was installed in the washing machine LG in 2005. Since then, inverter.Type engines have massively use leading firms in household washing machines. Unlike its analogues, the inverter is attached directly to the machine drum and does not need belt transmission and bearings.

The advantages of the inverter with a direct drive are considered simplicity of the design, compactness, the ability to assign various modes of operation, low noise and high efficiency due to the lack of loads from belt transmission friction.

The inappropriateness of repair in the event of an electric motor breakdown is considered a minus. The cost of recovery may be more than the engine itself costs. The impossibility of applying in various home.Made machines and mechanical devices due to the design features of inverters is also considered a disadvantage.

Device and repair of Beko washing machines 6000

Washing machines of Beko Series 6000 are the most massive model range of ARCELIK products.S., sold in recent years in the Russian market. This series includes both the simplest products and models with a wide set of functions, produced both in a 54 cm with a depth of 54 cm and dry linen 5 kg, and in a “narrow” version. With a depth of 45 cm and loading of dry linen 4.5 kg.

High consumer qualities, simplicity and reliability of the design, interchangeability of components and the convenience of repair operations make machines of this series convenient to use and maintenance.

Below are the technical parameters of the 6000 washing machines that have the same command.Apparatus (KA), an electric motor, etc. D. And general electrical circuit. The exception is only the WBF 6004 XC model, where there is no adjustable thermostat (instead there is the function “washing in cold water”), the speed of spin is 400 rpm and, accordingly, there are differences in the configuration and scheme. The machine of this model is separately considered in the next paragraph.

Many technical characteristics and service recommendations here are also related to washing machines of the former years of production (models Y-2312S, Y-2416, Y-3350) and LG washing machines (Models WD-6003C, WD-6004S, WD-8003C. WD-8004s and WD-1004s).

Rice. One The control panel of the washing machine Y-2312C

In Fig. 1 shows the control panel of the Y-2312C washing machine, in rice. 2 Panel of Control of washing machines WB-6105 XG, WB-6106 XD, WB 6108 XD, WB 6108 XE, WB 6110 XE and WB 6110 XES, in rice. 3 Panels for the control of washing machines WB 6106 SD, WB 6108 SE, WB 6110 SE and WB 6110 SES.

Rice. 2 Washing machines control panels WB-6105 XG, WB-6106 XD, WB 6108 XD, WB 6108 XE, WB 6110 XE, WB 6110 XES

Rice. 3 Wir 6106 SD, WB 6108 SE, WB 6110 SE and WB 6110 SES control panels.

Technical characteristics of the washing machines Beko series 6000 are given in the table. One

• The washing machine does not work;
• The washing machine does not gain water;
• The flood of water into the washing machine does not come from the separation of the detergent distributor, which should be involved in the program;
• The washing machine does not drain water;
• The washing machine does not heat the water (step 1 of the program B);
• The command.Control “hangs” on one of the steps of the program;
• The washing machine picks up water, but does not wash;
• When washing, the drum rotates, as when spinning;
• Luke door does not open.

Rice. 4 Fast search algorithm “Washing machine does not work”

Rice. 5 Fast search algorithm “The washing machine does not get water”

Rice. 6 Fast search algorithm “The flood of water into the washing machine does not come from the detachment of the detergent distributor, which should be involved in the program”

Rice. 7 Fast search algorithm “The washing machine does not drain water”

Rice. Eight Fast search algorithm “Washing machine does not heat water (step 1 of the program B)”

Rice. Nine Fast search algorithm “The command.Control” hung “on one of the steps of the program”

Rice. Ten Fast search algorithm “The washing machine picks up water, but does not wash“”

Rice. Eleven Fast search algorithm “When washing, the drum rotates, as when spinning“”

Rice. 12 Fast search algorithm “Luke door does not open“”

Designations of colors of electrical wires in the diagram:

In Fig. 18-22 are given components of the washing machines of the Beko series 6000, and in table 2 their list is given.

Rice. Eighteen Components of washing machines Beko series 6000 (case)

Rice. Nineteen Components of washing machines Beko series 6000 (control panel)

Rice. 20 Components of washing machines Beko series 6000 (electrical components)

Rice. 21 Components of washing machines Beko series 6000 (tank and drum)

Rice. 22 Components of washing machines Beko series 6000 (hydraulic components)