The gas stove is constantly clicks: why does the gas stove click and how to eliminate it
Modern gas stoves are equipped with an automatic ignition system. This is very convenient and practical: you can forget about matches and lighters. It is enough to press a special button or even, almost like in an electric stove, turn and press the burner handle. And there will be a spark that ignites gas.
The disadvantage of such convenience is possible breakdown of the car repair system. Often, housewives are faced with a problem when the ignition does not turn off: that is, clicks are constantly heard and a spark is visible, even if you do not approach the plate at all.
Не включается варочная панель. Что делать?
Note! This problem is characteristic of gas plates with an electrical ignition system. Piezoelent is arranged differently, and its malfunctions in this article are not considered, since all modern household plates use electric light. Pierzage system is found only in old Soviet or modern tourist plates (without connecting to electricity).
What to do if the gas stove does not light up
All breakdowns of gas plates can conditionally be divided into two huge groups:
Let us see the symptoms and prerequisites for defects because of which gas in the stove may not be supplied:
In all cases, when the burner on the gas stove is poorly burning, the reason should be found in gas supply systems and most likely immediately contact qualified specialists.
Most of modern gas slabs and hobs are equipped with protection against gas leakage, which is called gas control. The principle of operation of this system is not difficult: a thermocouple (flame sensor) is installed on each burner). After pressing the gas supply handle, an electrical.Glass is triggered and the gas supply electroblop is manually revealed from the effort of the user. If the thermocard is warming up to a suitable temperature, an electric shock appears to the electric valve winding. Thanks to this, the valve is kept in an open state, and the gas stove burn does not rot, regardless of the presence of pressing the burner on the handle of turning on the burner.
With problems of the gas control system, the gas glow while you hold the control handle. After releasing the handle, fire on the burner fades away. Damage may appear due to the release of the thermocouple or due to violation of the adjustment of the gas control sensor. This often happens after cleaning the place around the burner or thermocouple itself. Set the thermocouple in the middle position relative to the fire and the gas comfort will begin to light up normally. The thermocouple will have to be changed to the latest,
There are times that the flame of gas stove with gas control is fading away due to low pressure in the gas supply system. But before you call the gas service, make sure that the valve is open near the stove. But in most cases, a gas stove does not hold a flame due to a blockage of a nozzle, into which water or the remnants of a “escaped” food hit. With all this, the burner can from time to time and light up, but the fire will have a non-natural color (due to violation of gas and oxygen ratio) and spontaneously turn off.
Occasionally, but it happens that the blockage “makes its way” and to the crane mechanism. He begins to cut with additional effort, and from time to time and wedges completely. The same symptoms occur with dry lubrication or mechanical breakdown of the crane. To carry out such repairs, you need to call the master, because unskilled intervention can lead to a gas leak and unexpected consequences.
Why electric fire stopped working
The block is faulty (high voltage pulses converter). The main element in the circuit. Induces high voltage pulses on the discharge. Consists of capacitors and induction coils. Details of repair and replacement are not subject to. Sige: there is no spark on all burners.
The button or its contacts is faulty. The second element in the diagram. The starting mechanism of the electric carpet. Consists of the case and two contacts. The reliability of contacts is not guaranteed completely, oxidized, melted, destroyed. Sige: does not spark when you press the handle.
A defector (a candle of ignition) is faulty. It produces an electric pulse of a small duration opposite the firing opening of the burner. The crack in the insulator violates the stability of the spark, rejects to the side. Sign: One burner does not light up.
It is worth mentioning the negative effects of moisture. If, after wet cleaning of the plate, the electric carfight sat spontaneously. No need to panic. Delete the device for 2-3 days, or until completely dry. You can speed up the process with a hairdryer by directing the flow of hot air under the crane handles.
Security measures
When conducting work on setting up an electric ignition of the slab, you should adhere to certain safety measures that will help you not only avoid unwanted injuries, but also prevent the occurrence of additional malfunctions in your home. If you had to disassemble the upper part of the stove, do not forget to pre.Turn off the electricity, and block the gas access to the stove. After repairing work to verify the performance of the gas and electricity, it should be submitted to it in short.Term mode and only after the work is completely completed, you can give complete access to these communications to it.
Thus, even having a little experience in communication with technology, you can independently eliminate small problems in its work. However, if a thorough breakdown has occurred, it is worthwhile to consult on the repair of the service master or provide the service with the service of the service to help you eliminate the malfunction.
The burner does not light up (does not ignite)
The breakdown manifests itself after long years of operation, the frequency of manifestation increases over the years. The cause of the occurrence: wear of the ignition block; violation of the insulation of the wire of the candle of ignition; Destruction and crack of the ceramic candle of ignition. To identify the cause, you should resort to cunning. Turn off the light in the kitchen in the dark. Turn on the electric fire and observe the spark: the complete absence of a spark on one burner. The wire is broken. The spark beats to the side, in the hob. A crack on a candle of ignition. The spark has a yellow or red color. The wear of the ignition unit.
Top 5 Reasons Gas Oven Won’t Heat — Gas Range Troubleshooting
The breakdown occurs from overheating of the surface components, is usually accompanied by the output of the error code to the display. This breakdown is protective in nature. Causes: uncontrolled heating of the burner; overheating of the touch sensor in the area of control. To eliminate the breakdown, the surface should be de.Energized for 15 minutes. After re.Turn on, if the error is repeated. The diagnosis of control board, namely the sensor and the heating relay. In the absence of a defect, the board changes.
The principle of operation of auto lights
To understand the cause of a malfunction of auto.Bank, you need to know how it works. It is not difficult to figure it out in the principle of its operation: the setting of the setting up the mechanism is made from the electric network, and its launch by pressing a special button and turning towards the gas supply regulator, in the direction indicated on the arrow depicted on the slab panel. The process of operation of this mechanism is as follows:
- When you press the arson button, the spark is converted due to the flows of electrical pulses.
- When turning the handle, opening a certain burner, gas is supplied to the burner.
- The spark received when the mechanism is triggered interacts with the gas, converting it into fire.
- The burner in which gas was supplied begins to burn.
You can release the handle a couple of seconds after turning. Just so much time is required so that the system is magnetized. Of course, in reality, the whole process of arson passes much faster than it is described here. The burner is on the light on which the spark is. The arson button itself is located on the slab panel, next to the gas supply regulators.
In the old.Style plates, the ignition process is slightly different from gas burning in new models. Its difference is that the spark is supplied immediately to all the burners, but only the one, whose valve was turned over.
For old and new models for the operation of the auto.Bank mechanism, its mandatory connection to the mains is necessary.
Why electric fire stopped working
One. The block is faulty (high voltage pulses converter). The main element in the circuit. Induces high voltage pulses on the discharge. Consists of capacitors and induction coils. Details of repair and replacement are not subject to. Sige: there is no spark on all burners.
The button or its contacts is faulty. The second element in the diagram. The starting mechanism of the electric carpet. Consists of the case and two contacts. The reliability of contacts is not guaranteed completely, oxidized, melted, destroyed. Sige: does not spark when you press the handle.
A defector (a candle of ignition) is faulty. It produces an electric pulse of a small duration opposite the firing opening of the burner. The crack in the insulator violates the stability of the spark, rejects to the side. Sign: One burner does not light up.
It is worth mentioning the negative effects of moisture. If, after wet cleaning of the plate, the electric carfight sat spontaneously. No need to panic. Delete the device for 2-3 days, or until completely dry. You can speed up the process with a hairdryer by directing the flow of hot air under the crane handles.
Common signs of a malfunction
Unfortunately, the device of automatic gas setting up. Achilles heel of many hobs. According to the consolidated statistics of service centers, its breakdown leads a list of problems with gas equipment. What signs indicate this breakdown? If you turn the oven control handle, but the flame does not appear, this indicates the failure of the electric carpet. A similar situation and when automation constantly works, clicks and other sounds are heard, but the gas does not light up. In some cases, a faulty electric light can continue to work on its own, without the participation of the user. One of the symptoms may also be knocking out a protection machine on an electric shield.
Repair of electrical adjustment of the slab in the company “Gazervice
Most of the breakdowns that cause a defect in the operation of electrical adjustment are non.Hazardous to the user. However, constant crack can drive crazy. If this nuisance befell you, if necessary, you must eliminate it by the forces of professional masters. Gas stove is a potentially dangerous product due to the possibility of gas leakage, do not try to disassemble yourself, repair the electric glass of the plate. Call us and order masters at home. We accept applications through the feedback form.
We go to any district of Moscow and the Moscow region:
VAO, SEAO, Yuzao, North.West I, CAO, CAO, SOA, CJSC, VAO.
We carry with us all components and spare parts.
8/495 / 506-81-52. We are waiting for your calls every day from 9.00 to 21.00
