Hotpoint Ariston does not drain water

What could be the cause of the water is the washing machine Ariston

Often the user himself is to blame for the fact that water does not merge from the washing machine, and the equipment has nothing to do with it. For example, an incorrectly selected program in which the machine does not drain water so that the underwear does not grind. Before suspecting a breakdown, you should start small and re.Read the instructions. If an incorrectly installed program is confirmed, then the necessary should be installed and the washing cycle should be rested with. There are frequent cases of an overclock of the drain hose. This option is also worth checking. A blockage of the hose itself, siphon or sewer system is possible. Good to know!

When the siphon or sewage is clogged, the water is upward, it will not go out. There is no pressure in the drain. After all, the water is pumped not a pump, but a pump unable to create high pressure.

If the above problems have not been confirmed, then a malfunction in the machine itself. The automatic machine may not drain the water for:

• Blockage installed on the plow of the filter;
• Failure of the pump;
• Breakdown of the programmer, control module, program failure;
• The failure of the water level sensor (press start).

Let’s try to understand how to determine the cause of the failure.

Ariston washing machine does not drain water. What to do

Often housewives and consumers are faced with the fact that the Ariston washing machine does not drain water. This creates certain difficulties in further operation. It is not only the impossibility of opening the door, getting things and starting the drain, but in the absence of further pressing and the completion of the washing cycle. As a result, the water stagnates inside, which leads to the oxidation of the drum and the appearance of mold. The call of the master is always expensive, so this article will consider independent ways to eliminate problems.

Why does the technique not drain the water?

The reasons for the problems in Ariston:

• Program failure. Perhaps there was a network overvoltage or disconnecting of electricity, which allowed the machine Ariston to “think” about the performance of the task, and specifically about the plum, or completely stop the work. Knock on the top cover or the presence of heavy objects similarly lead to a failure, which also stops the drain.
• The drain hose is blocked by extraneous objects.
• Blocking the sewer system.
• Extraneous objects fell into the filter.
• Damage or pump breakdown.
• Lengthening the hose, or location at an unacceptable level.
• Opening or closing the wiring.

Part of the problem can be solved independently, while the car will remain in working condition. The owner of Ariston was lucky if his machine is equipped with a Smart function. Diagnostics. Using special keys, Wi. Fi and smartphone, the machine is diagnosed, and after a few seconds a notification of breakdowns, a possible reason and ways to eliminate it, is received. Such an option is factory, but is installed in more modern Ariston models.

Program failure

• Restore the program. Click on the launch of the washing cycle and wait. In the absence of the reaction, turn off the machine and start the drain.
• Remove heavy objects from the lid and try to restart the drain.
• If the problem is not solved, then the matter is not the program.

Hose

• Check the bending radius. At least 50, maximum 80 cm. If it is too much or shortcomed, then the water simply will not reach the drain. The car will receive a signal for built.In sensors, and the team will remain unfulfilled. You can fix the problem using a special clamp, which is in the configuration of the washing machine.
• Proceeding is possible. This happens if you come or overturn something heavy. The situation will not only stop the cycle, but also break the rubber. Remove extraneous objects.
• Check the connection. The fastenings could move away, and the smart car decided not to drown the neighbors from below.

Sewage

• Open the tap, or lower the toilet tank, if the water does not leave, it is necessary to clean the system.
• When disconnecting the drain source from the corrugation, the washing machine must be in the off state.
• Eliminate the blockage.

Filter

• Deal in the washing machine.
• Lay the towel under the bottom.
• Open the filter protection. It is located below on the right side (if the car is facing the owner).
• Turn the cap to the right and twist it.
• Wait for the water to stop flowing.
• Remove the filter and examine for excess contents: buttons, coins, washing powder.
• Rinse the part. Water should not be hot.
• Scroll through the impeller (located behind the filter) if it moves freely and does not jam, then the pump is in order.

Water pump

• After draining the water and extracting the filter, start the squeezing mode.
• If the impeller remains motionless, perhaps problems with pomp or pump.
• When the pump makes an uncharacteristic noise, most likely water leaked into it. In such cases, it must be replaced.
• For diagnosis, it is necessary to remove the lid of the washing machine.
• You can eliminate the problem yourself if, after a visual inspection, a slight breakdown is visible.
• Inspection did not give results? Then contact the master, which is carried out by highly qualified repair of Ariston machines.

Wiring

• Remove the top cover and inspect the wires.
• Perhaps the previous squeezed contributed to the disconnection of the wire block from the board. Return the block to its original position and run Ariston again.
• Check for the absence of moisture or breakup rupture

The washing machine does not drain water and does not push

The squeezing mode of things is launched if the drain of water works correctly. If after solving the problems of drain the seas did not start, then the presence of more difficult problems is likely.

Reasons and solutions

• Poem failure.Usually, an error F18 is displayed on the display, which means this breakdown. Unfortunately, it will not be possible to eliminate the problem independently, since the system is required.
• Flapsed the drain. Eliminate the problem and restart the program.
• Damage to the press. Remove the top and inspect the load. Replace if necessary.
• The failure of the tachogenerator (Hall sensor). Check the mount if the part is ill, it is necessary to tighten it. Scroll the drum manually and substitute the voltage measurement (no more than 0.2). The data is positive? Then the probability of a defect in pollution. Clean the sensor and set in place according to the instructions. With mechanical damage, a change of part is needed.
• The bearing broke. Determine the breakdown is simple: when rotating the drum, a loud knock or a rumble is heard. In this case, the bearing is replaced.
• Modeling.Ariston‘s car has only a collector engine, most likely the brushes have worn out or the belt broke. The wear of the parts is visually visible. You can replace yourself.
• Management module. Water, excessive vibration, the machine survived a strong blow, this leads to a decrease in the functionality of the “heart” of Ariston. In such cases, the module visually inspects the absence of moisture and disconnecting contacts. If necessary, it can be removed and cleaned. If after manipulations, the program does not start, or indicators begin to flash, it is recommended to contact the workshop for the repair of washing machines.

How to drain water from Ariston washing machine?

It is unpleasant when the washer suddenly “hungs” with a full tank. Especially if the problem is not solved by the reloading of the system and repeated pressing the “drain” button. With an automaton that does not respond to external commands, you will have to act forcibly, gently drain the water from the Ariston washing machine and conduct a comprehensive diagnosis. You can drain the water in several ways. Fast or slow, safe or emergency. To choose the right one, it is worth considering all options and evaluate the nature of the problem.

How to drain the tank machine?

If the washer refuses to “respond” to the commands, then the “drain” button will not help. You will have to act manually. Fortunately, the manufacturer provided alternative options for devastating the tank. Over, you can drain the water in several ways at once: you only need to evaluate the situation and choose the appropriate method.

The drum is forcibly exhausted through:

• The drain hose, while the pump is not activated;
• Twisted garbage filter;
• Emergency opening of the door of the hatch;
• Disconnected drain pipe.

Before forced draining, it is necessary to turn off the machine from power supply and water supply!

The method of devastating the tank is selected depending on the situation. In any case, it is necessary to first prepare a place for the procedure and the washer itself. In order not to flood neighbors, you should deal with the nuances of the upcoming plum in advance. Recommendations and instructions for each method are given below.

We remove the filter and water will flow out

Almost 100 percent way to quickly and simply “drain” the machine-“go” through the garbage filter. This is a plastic spiral nozzle that protects the pump from garbage and objects that accidentally fell into the drum. Is the “spiral” behind the technical hatch in the lower right corner of the Ariston corps.

• We check that the washer is disabled from all communications;
• We wait until the water in the tank has cooled (otherwise you can burn yourself);
• Using a flat screwdriver, pry the cover of the technical hatch and remove it;
• We find a plastic black round cover. A garbage filter;
• Gently tilt the asset body to the left and substitute an empty container under the garbage filter;
• Additionally, we cover the surrounding space with old rags and newspapers;
• We take for the protruding part on the “trash can” cover and unscrew the filter for several revolutions until water is pouring from the hole;

It is not necessary to twist the garbage filter! Leaving it in the groove, you can adjust the degree of water pressure!

Emergency drain through the garbage filter among the safest and fastest. If the machine broke and does not respond to commands, it is better to empty the tank just like that. The advantage of the method is that there is no need to disassemble the washer or manually scoop up the water. However, it is worth being prepared for the fact that a certain amount of dirty fluid will spill past the basin.

Drain sleeve

The second method involves the use of a drain hose. Precisely, it is necessary to persuade the sleeves below the level of the drum and let water, thanks to the so.Called “siphon effect”. The main thing is that it is possible to disconnect the corrugation from the sewer pipe. To emergency drain the water through the sleeve, you must adhere to the following instructions:

• Disconnect the hose from the sewage system (free the clamp by pliers and unhook the corrugation from the pipe);
• Renounce the hose from the back of the washing panel by removing the provided plastic locks;
• Lower the corrugation below the level of the tank of the Ariston washing machine, putting the free end in the basin, bath or toilet;
• Wait until the water by gravity leaves the washer.

Plum through the hose is possible only on Ariston models not equipped with an internal loop or a check valve.

Water is drained through the main hose simply, quickly and without unnecessary preparations. But there is one catch. The method does not work on all machine guns. Modern washing machines with a special inner loop or check valve block a dildo, preventing arbitrary leakage during washing. As a rule, we are talking about models released after 2015. To clarify whether it is possible to devastate the drum through the sleeve on the existing washing machine, it is enough to study the user guide.

Emergency “autopsy” of the machine

If for some reason to drain hotpoint Ariston through the garbage filter and the hose, you will have to turn to “heavy artillery”. The latter means emergency opening of the hatch door followed by scooping up water. This procedure will require more effort and time, so we proceed to it in extreme cases.

• We evaluate how much water is in the tank (if the fluid level is above the edge of the drum, then we tilt the machine back and fix it);
• We open the machine;
• We scoop up the water.

The washing machine does not drain the water, what to do?

After the washing was completed, you found that the underwear is wet, or what was even worse in the drum? You are at a loss of what could have happened, why the washing machine stopped draining water and squeezing linen? And what to do with it in general? In this article we will analyze all possible malfunctions, and some of them will eliminate on our own.

• The main causes of malfunctions of water drainage
• DIY breakfast elimination
• Cleaning the filter
• Inspection of the pipe
• Check the impeller
• How to check the pump for a malfunction and replace it?
• Electric wiring malfunction
• The water level sensor is faulty (Pressostat)
• The control module is faulty (programmer)
• Conclusion

The main causes of malfunctions of water drainage

If the water does not merge in the washing machine, the causes of this problem may be as follows:

• The connecting pipe clogged with garbage, which is located between the pump and the tank.
• An extraneous object fell into the drain pump (pump).
• The garbage in the pump filter accumulated.
• The pump itself failed.
• The drain hose clogged.
• Problems with sewage or siphon.
• The water level sensor does not operate (Pressostat).
• The control module (programmer) is defective).

Having learned the reasons affecting the correct squeeze and drain, you can proceed with the inspection and repair of the machine, but before starting, it must be de.Energized.

Cleaning the filter

In order to exclude the blockage of the filter, due to which draining in the washing machine may not work, it must be checked and cleaned by the situation. You can find it on the front side of the unit, at the bottom of the case. There you will see a hidden panel that is closed to the latches. Open it with an ordinary flat screwdriver. Open the panel carefully, with a screwdriver you can easily break the latches. After opening the panel, you should see a filter that is twisted counterclockwise. If you can’t twist the filter with your hands, you can use the pliers.

In view of clogging, you need to be prepared for a certain amount of liquid. It is better to prepare in advance, for this a rag and any capacity will come in handy.

When you unscrew the filter and find that it is really scored, the problem can be called solved. Just clean it from garbage and tighten it in place.

Inspection of the pipe

If the cleaning of the filter did not give a result, then you need to continue repairs and proceed with the examination of the pipe. The pipe is called the hose that connects the tank and the pump, respectively, if it clogs, the machine does not drain water and does not squeeze the laundry. The exit from the tank can also be clogged, the pipe is connected to it, an extraneous object can get stuck in this hole, it can also prevent fluid passage.

To clean the pipe from foreign objects, on the back side you need to find bolts and spin them. Next, the hose is removed, you must first get rid of the clamps with the help of the pliers.

To check whether there is dirt in it or not, it can be felt, clutching in the hands. In the presence of garbage, it must be eliminated. You can do this under the pressure of running water using an ordinary brush or rag. As soon as the pipe is cleaned, it should be installed on the original place according to the above procedure, in the reverse order.

After installing the pipe in place, make sure that the clamps are well squeezing the connection place to avoid leaks!

Check the impeller

What to do if previous methods have not solved the problem?

The malfunction can lie in the faulty state of the impeller. In order to make sure this, you need to check it for jamming. Free scrolling may also indicate its non.Service, if the impeller is working, it should scroll through small jerks. It is located on the pomp in front, immediately behind the filter. A malfunction can occur when when working on the impeller, it does not give it any extraneous thing, for example a coin or a match. Because of this, the pump in the washing machine usually buzzes, since there is a load on its engine winding. First, it is better to check it with manual method, trying to turn it out with your fingers. If an extraneous object is visible during scrolling, it should be removed. After the manipulations carried out, the car does not further squeeze the laundry? Then it’s time to start inspection of the pump.

The impeller from the pump

How to check the pump for a malfunction and replace it?

The reason why the drain in the washing machine does not work, it can lie in a faulty pump (pomp). In order to find out, you need to be described above, remove the filter. Then, set the program for the squeeze and look at the place where the filter stood. To see well, you need to provide good lighting, for example, highlight a flashlight there. If you see that the impeller of the pump remains without movement, then this means that the drain pump is faulty. Otherwise, the impeller would have rotated, since it had already been checked for the presence of foreign objects. There is also another method of checking, for this you need a tester or a different multimeter. With it, you can check the integrity of the winding, for this it needs to be called. When breaking the pump, it often is simply changed to a new one, since its repair is complicated and it will cost half its price. Most often they simply burn out, due to a large load that occurs when the impeller is jammed.

Drill pump (pump)

It will not be difficult to purchase it, there are standard pumps on sale that are suitable for almost any model of washing machines: Samsung, LG, Indesit, Ariston and others.

After the new pump is purchased, it should be installed in the place of the broken. To replace it, you need only a screwdriver and plot. The procedure is quite simple:

The appearance of a breakdown, its causes

If you begin to notice that the washing machine does not drain water, you need to pay attention to its behavior. First of all, you should figure out what manifestations have the indicated breakdown. Among the “symptoms” such as:

• Slow drain, with a possible software failure;
• After launch, washing will stop when draining;
• Several times the water merges, but several times;
• When washing, everything goes in standard mode, but at the time of rinsing the drain stops;
• The seas is not activated at the end of the drain.

Which causes the appearance of a breakdown? The reasons are diverse, but in a particular case to determine it will help the behavior of the washing machine. First of all, the technique can issue an error code indicating the nature of the malfunction.

• The pipe connecting the pump and the tank clogged.
• A small object clogged the pump.
• The garbage filter clogged.
• The pump was out of order.
• Siphon or pipes clogged.
• The hose for draining water clogged.

Drain pump

If the problem is still relevant, and draining water still does not occur, you will need to go to the next stage. Within its framework, we need to check the pump, or rather, find out if the impeller has jammed. She is exactly the filter, and if there was even a small item (for example, a rivet from clothes), this can cause a breakdown.

In view of what was said, at the initial stage you need to try to scroll through the impeller. When it spins, and there are no foreign objects. It is in good. But in reverse situations, you will need to immediately remove the extraneous thing. If this did not solve the problem, check the electrical pump electrics.

For these purposes, the filter is shot, guided above the above instructions. After set the pressing mode and illuminate the filter hole. A small flashlight or a flash of a phone is suitable for this. When the impeller is in a stationary state, this is a clear evidence. So, the malfunction has already been found, and we will need to move on to the next step. Installing a new component.

But before replacing the drain pump, it will need to buy it. The design of most washing machines includes standard details, in view of which we without difficulties can purchase the suitable for us in the nearest household appliance store or in the construction market. And if the points of sales are located at a decent distance from your home, you can go to the open spaces of the World Wide Web, and find the necessary set in online stores.

So, the part was bought, and the time has come to install it. To do this, dismantle the drain knot, and disconnect the drain pump from it. Then, with special attention, remove all the wiring from it, take the part purchased and replace. We return all the wiring and other details to its original position, and then collect the HotPoint Ariston washing machine to its original state.

At this stage, the question: what to do with non.Working plum is completely disassembled. And you can easily restore the performance of the equipment with your own hands at home using the presented instructions.

Interesting:

• Review of Ariston washing machines with vertical loading
• Review of built.In dishwashers Ariston 45 cm
• Ariston washing machines
• Reviews about HotPoint Ariston dishwashers
• Repair of faults of washing machines Ariston
• Reviews about Ariston washing machines. Hotpoint

The reason why Ariston does not drain water

The fact that the drain is impossible to immediately find out by stopping the washing process. This can happen in the middle of washing or at its completion. The malfunctions can also be judged by the fact that after pushing in the drum, part of the water remains. This suggests that in principle the drain occurs, but the washing machine Ariston does not drain the water completely.

The impossibility of full and rapid drain of water is indicated by the signs that are clearly visible even to an inexperienced person:

• Water merges longer than usual, flows with a thin stream;
• The entire control system of the device freezes at the beginning of the drain, although the washing cycle itself was successful;
• The drain occurs with a certain interval. For example, through one washing;
• The drain is absent after the squeezing procedure;
• Draining of water is possible only after washing, and when rinsing it is absent.

The drain can be complete and incomplete. And in the second case, the malfunction can be recognized in the simplest way. Even after spinning, they remain wet.

How to drain water quickly

To diagnose the breakdown yourself, you first need to drain the water from the drum.

• Through the drain hose. This method comes to mind the first. The main thing here is to make the sleeve lying below the level of the tank. In this case, water will pour itself. Further, substitute a bucket or any other container under the tube wait until the liquid comes out.
• Through the drain filter. Here you need a low container, because the filter is located almost by the floor. Put the container under the filter hatch and carefully unscrew the cork. You don’t need to do this completely. It is enough to wait for the moment when the water is piled.
• Emergency hose. Some of the manufacturers of the equipment (far from everyone) introduces a special emergency hose into their devices, just for cases when you need to urgently drain the water in the tank. It is located under the plug, where the filter is. Remove the phone, lower it into the cooked container and remove the plug.
• Drain pipe. It is worth resorting to this method only when the previous methods did not work. Open the rear panel of the machine and find the drain pipe. Most often he is under the drum. Throw rags on the floor and put the container under the pipe. Remove the clamp and carefully start disconnect the pipe itself. Get ready that there is a lot of water from the tank.

The car works, but washing does not start

If your washing machine turned on, but the washing could not be launched, the reasons why this happens can already be in another.

All indicators in working condition

Turning on the washing machine and choosing the washing mode, you found that it did not start, although before that the equipment behaved as usual: all the indicators lit up, the sound greeting sounded. First of all, make sure that the hatch of the washing machine is tightly closed and nothing is stuck in its lumen.

After the start of the program, the door should be closed to the lock, otherwise the protective mechanisms of the equipment will not allow you to fill the tank with water.

If the hatch is not blocked, then it is necessary to check the locking device for the presence of voltage in it. If it is absent, although the current is supplied, then the part should be replaced.

Make sure water enters the drum. Listen. Complete silence indicates that the flow of water inside is difficult.

Check if you have chosen the washing program correctly. Perhaps you synchronously pressed two or three buttons at once or not at all. Turn off the car from the network for a couple of minutes and, most likely, the failure will be removed.

Light indicators are randomly light up

If all indicators are randomly on the washing machine, the faulty wiring is all to blame. The Bosch washing machine, as well as the equipment of other companies (Indesit, Samsung, HotPoint, Ariston) have a characteristic feature. Their wiring is often in contact with other details, which affects its performance. Install a problem area using a multimeter and change it.

Blocked capacitors requiring replacements can give themselves to flashing all light bulbs in a random mode, or by simultaneous sunbathing.