How to adjust the refrigerator stynol in the heat

Steinol refrigerator Two.Chamber how to adjust the temperature

Stynol refrigerators. A product of domestic production, the manufacture of which has been carried out in Lipetsk since 1993. Currently, the plant is the property of the Italian concern Indesitis and is engaged in the release of products under two trademarks: Indesit and HotPoint-Ariston. However, due to the durability and reliability of old Stinol’s old refrigerators, they are still used in many Russian families. In the article we will share with you the features of the functioning of these devices and give key points from the instructions for their operation.

Operating instructions for the refrigeration equipment of the stinol trademark are similar to each other for all models. They reflect information on the use of units and prevent their failure as a result of incorrect actions of the owner.

The general operating guide contains the following sections:

• General instructions. Information about the purpose of the device;
• Technical data, dimensions of the device and equipment;
• The device of the model and the principle of its functioning;
• Safety requirements. Features of connecting the device to the electric network;
• Preparation of the device for work;
• The rules of operation and care for the device, in particular, control of the modes, features of the distribution of temperature in existing cameras, tips on the rational placement of products;
• Possible malfunctions of the unit and methods of repair;
• The manufacturer’s warranty.

Next, we consider the basic technical characteristics of the popular models of Stinol refrigerators and get acquainted with the principles of their functioning.

Model 101

Steinol 101 refrigerator. A two.Chamber device that consists of a refrigerator and freezer compartments. The control of the unit is carried out due to the electromechanical method of regulation. The model has one compressor and two independent evaporators that provide air cooling to the required level in both departments.

The average temperature of the refrigerator is 5 ° C, the freezer is not higher.18 ° C. Maintaining the temperature at a given level. A consequence of the periodic turning on and off the compressor using a thermostat and a launcher relay.

The reinforcing compartment of the device is carried out automatically before the next inclusion of the compressor. The accumulation of melt water occurs in a special container on the compressor, after which it is evaporated.

Thauing the freezer should be carried out in manual mode when a layer of hoarfront is over 5 mm.

Model 103 (RF S 345)

Two.Chamber refrigerator Stinol 103 with the lower arrangement of the freezer is equipped with two compressors and two evaporators with a sequential connection. This provides autonomous operation of the refrigerator and freezer compartments with the possibility of autonomous temperature adjustment and turning off one of the cameras using controllers on the control panel.

Defrosting the refrigerator compartment is carried out automatically by the drip method. The freezer department must be defrosted manually.

Model 104 (NF 330 4T)

Stinol 104 is a one.Compressor refrigerator, which consists of three chambers: a refrigerator, freezer and a retractable compartment for placing vegetables and fruits. Equipped with four temperature zones, the thawing of which is automatically. The temperature regime of each compartment is adjusted autonomously, which allows you to set the optimum temperature for storing various products.

The freezer compartment, located in the upper part of the apparatus case, is equipped with the No Frost system, which ensures automatically thawing the evaporator when the need occurs.

The refrigerator compartment is equipped with a crying evaporator providing food to cool. Autonomous retirement department for storage of vegetables is located under the refrigerator. Its cooling occurs due to the penetration of cold air from the main compartment through a special hole on the rear wall of the case. A mode of 8 to 14 degrees is installed in a retractable container for vegetables.

Model 107

Stinol 107 device is a two.Chamber refrigerator equipped with one compressor. The cooling of the freezer compartment is carried out due to the functioning of the evaporator of the Knou Frost and fan system. The refrigerator compartment is cooled thanks to an autonomous evaporator located on the outer surface of the posterior wall.

The minimum temperature supported by the freezer is.18 degrees Celsius. The additional capabilities include the supermarket function.

Model 116 EL

The model for household use of Stinol 116 EL is a separate refrigerator with a freezer located in the lower part of the case. The device has the following technical characteristics:

The refrigerator compartment of the device is equipped with four shelves, two opaque containers for vegetables and fruits, and with hinged shelves on a multi.Brux door like. In the freezer there are two boxes with folding lids and one retractable container.

Due to the lack of the function of automatic thawing the freezer, the electrical circuit is quite simple compared to other manufacturer models.

Model 123 l

The refrigerator 123 L consists of the following elements:

• Compressor;
• Drop.Type evaporator for refrigerator;
• The evaporator of the non.Frost system;
• Capacitor;
• Drainage filter;
• Capillary pipeline.

The freezer chamber of the device is located in the lower part of the case. It has a fairly large volume. 102 liters. The cooling of the refrigerator and freezer compartments occurs according to the double sparring scheme, as in the models of Stinol-101, Stinol-107. Thawing of both the main and minus compartments automatically.

The device works according to the following principle:

• When the refrigerator is included in the network, the compressor begins to draw a refrigerant vapor from evaporators through a special absorption pipeline;
• According to the discharge pipeline, these vapors are sent to the capacitor for cooling and liquefaction;
• In liquid form, the refrigerant goes to the evaporators channels, passing through the filter-dryer and the capillary tube;
• When boiling, the refrigerant goes into a gaseous state and absorbs heat from the cooled environment.

How to adjust the temperature in the refrigerator Stynol

After the stinol refrigerator is launched, it is necessary to make sure that the temperature in line with the parameters stated in the instructions. Upon reaching the mode, you need to measure, what is the temperature inside the chambers. In the refrigerator, it is convenient to use a glass of water placed for cooling on the middle shelf in the center. Water should take a temperature of 4-5 0 s.

In the freezer of the stinol refrigerator, on the “super” mode in the upper chamber, the temperature will decrease to 24 0 s, on all shelves at the middle position of the regulator, degrees must correspond to the number of stars, but not more.Eighteen.

To set the temperature electromechanically in the refrigerator Stinol is simply. When adjusting the temperature, you always need to strive for the average indicators, as the most rational. In the refrigerator, stynol is 5 degrees for the cabinet and.18 for the freezer.

How to regulate in drip models

The manufacturer recommends connecting power and adjust the temperature in the refrigerator after installing the product in the planned area. When location, it is necessary to leave the gaps between the side walls and the rear panel of the housing necessary for the correct circulation of the air (the dimensions of the gaps are given in the instructions for operation to refrigerated equipment). The refrigerator is withstanded in the room for 3-4 hours for uniform distribution of the refrigerant, and then connected to the household electrical network.

Which manufacturer is used at home?

• Instructions on how to set the temperature in a double.Chamber Samsung refrigerator

• Bosch 16%, 158 votes158 votes16%158 votes. 16%of all votes
• Samsung 14%, 143 votes143 votes14%143 votes. 14%of all votes
• LG 14%, 142 votes142 votes14%142 votes. 14%of all votes
• Atlant 6%, 65 votes65 votes6%65 votes. 6%of all votes
• Indesit 6%, 63 votes63 votes6%63 votes. 6%of all votes
• Electrolux 6%, 59 votes59 votes6%59 votes. 6%of all votes
• Philips 3%, 32 votes32 votes3%32 votes. 3%of all votes
• Ariston 3%, 30 votes30 votes3%30 votes. 3%of all votes
• Xiaomi 3%, 29 votes 29 votes3%29 votes. 3%of all votes
• Beko 3%, 28 votes 28 votes3%28 votes. 3%of all votes
• Redmond 2%, 22 votes22 votes2%22 votes. 2%of all votes
• Candy 2%, 18 votes18 votes2%18 votes. 2%of all votes
• Whirlpool 2%, 18 votes18 votes2%18 votes. 2%of all votes
• Siemens 2%, 18 votes18 votes2%18 votes. 2%of all votes
• Haier 2%, 18 votes18 votes2%18 votes. 2%of all votes
• Gorenje 2%, 17 votes17 votes2%17 votes. 2%of all votes
• Karcher 1%, 15 votes15 votes1%15 votes. 1%of all votes
• Liebherr 1%, 15 votes15 votes1%15 votes. 1%of all votes
• Hansa 1%, 14 votes14 votes1%14 votes. 1%of all votes
• Midea 1%, 12 votes12 votes1%12 votes. 1%of all votes
• Vitek 1%, 11 votes11 votes1%11 votes. 1%of all votes
• Zanussi 1%, 11 votes11 votes1%11 votes. 1%of all votes
• AEG 1%, 10 votes10 votes1%10 votes. 1%of all votes
• Ibot 1%, 9 votes 9 votes1%9 votes. 1%of all votes
• BBK 1%, 7 votes7 votes1%7 votes. 1%of all votes
• DELONGHI 1%, 7 votes7 votes1%7 votes. 1%of all votes
• Kuppersberg 1%, 6 votes6 votes1%6 votes. 1%of all votes
• Miele 1%, 6 votes6 votes1%6 votes. 1%of all votes
• Zelmer 0%, 5 votes5 votes5 votes. 0% of all votes
• Dyson 0%, 5 votes5 votes5 votes. 0% of all votes
• Thomas 0%, 5 votes5 votes5 votes. 0% of all votes
• Nord 0%, 4 votes4 votes4 votes. 0% of all votes
• Scarlett 0%, 4 votes4 votes4 votes. 0% of all votes
• Smeg 0%, 2 votes2 Voices2 Voices. 0% of all votes
• Ilife 0%, 1 voice1 Voice1 Voice. 0% of all votes

Total votes: 100922.01.2020 × you or from your IP have already voted.

The temperature background in obsolete single.Chamber installations is carried out using the thermometer. The thermometer is placed inside the refrigerator, and the temperature corrector is set in the middle position. The equipment should work for 2-3 hours, then the thermometer is checked. If the thermometer shows 2 5 ° C, then the equipment setting is considered correct. Then you should check and configure the temperature background in the freezer compartment, which should be in the interval.21.18 ° C.

In two.Chamber equipment (for example, Steinol 150), the thermostat is located on the upper edge of the case. Temperature corrector allows you to turn off the equipment (position off).

To increase the degree of cooling, the handle rotates clockwise; The manufacturer recommends installing the regulator in the central position.

With additional loading of a refrigerator or freezer with warm products, it is necessary to lower the temperature background inside the refrigerator.

Instructions for two.Chamber refrigerators Stinol

How to adjust the temperature in a two.Chamber refrigerator Steinol 101

Steinol 101 refrigerator. A two.Chamber device that consists of a refrigerator and freezer compartments. The control of the unit is carried out due to the electromechanical method of regulation. The model has one compressor and two independent evaporators that provide air cooling to the required level in both departments.

The average temperature of the refrigerator is 5 ° C, the freezer is not higher.18 ° C. Maintaining the temperature at a given level. A consequence of the periodic turning on and off the compressor using a thermostat and a launcher relay.

The reinforcing compartment of the device is carried out automatically before the next inclusion of the compressor. The accumulation of melt water occurs in a special container on the compressor, after which it is evaporated.

Thauing the freezer should be carried out in manual mode when a layer of hoarfront is over 5 mm.

How to adjust the temperature in a two.Chamber refrigerator Stinol 103 (RF S 345)

Two.Chamber refrigerator Stinol 103 with the lower arrangement of the freezer is equipped with two compressors and two evaporators with a sequential connection. This provides autonomous operation of the refrigerator and freezer compartments with the possibility of autonomous temperature adjustment and turning off one of the cameras using controllers on the control panel.

Defrosting the refrigerator compartment is carried out automatically by the drip method. The freezer department must be defrosted manually.

How to adjust the temperature in a two.Chamber refrigerator Steinol 104

Stynol-104 Moroziner is three-chamber and consists of refrigerated, freezer and retractable (for storing vegetables and fruits) chambers. Freezer, located at the top of the refrigerator, equipped with a “no frost” system with cold air circulation and automatic thawing of the evaporator. The timer periodically turns off the compressor, and the fan, and turns on the heating elements of the evaporator and the pallet of the freezer. During the melting of a layer of hoarfrost on the evaporator, the water flows onto a heated pallet and falls on the channels on a tray for collecting melt water, where it evaporates. Thermoregulator is located on the top control panel. Turning the handle of the thermostat clockwise increases the mode of operation of the refrigerator. We recommend installing a thermostat in the middle position.

How to adjust the temperature in a two.Chamber refrigerator Steinol 107

Stinol 107 device is a two.Chamber refrigerator equipped with one compressor. The cooling of the freezer compartment is carried out due to the functioning of the evaporator of the Knou Frost and fan system. The refrigerator compartment is cooled thanks to an autonomous evaporator located on the outer surface of the posterior wall.

The minimum temperature supported by the freezer is.18 degrees Celsius. The additional capabilities include the supermarket function.

How to adjust the temperature in a two.Chamber refrigerator Steinol NF 330 4T

STINOL NF 330 4T. Representative of three.Chamber refrigerators with one compressor. Equipped with four temperature zones, the thawing of which is automatically. The temperature regime of each compartment is adjusted autonomously, which allows you to set the optimum temperature for storing various products.

The freezer maintains the temperature to.18 degrees Celsius. A mode of 8 to 14 degrees is installed in a retractable container for vegetables.

How to adjust the temperature in a two.Chamber refrigerator Steinol 110

Adjusting lambs with risk for both camera has the same number of working positions. 5 of them. But thermostats for the refrigerator and freezer use different. The No Frost system is installed in the freezer, the thermostat has a diagram with a cyclic inclusion of a dry ice recovery system.

STINOL refrigerator instructions include a section in which there are instructions on how to adjust the temperature. Both cameras have a control and risk handle for turning. The number 1 corresponds to the highest temperature in the regulation range, the number 5 is low. The position is indicated on the pad.

Initially, indicators are exhibited in the middle part of the scale, even before the device is turned on. According to the instructions, the cold should get in the cells in 4 hours, and only then you can place products there.

It is necessary to adjust the handle gradually, turning 1 risk after 5-6 hours with temperature measurement inside the chamber. If the device does not respond to commands, it is necessary to determine if the thermostat works.

How to adjust the temperature in a two.Chamber refrigerator Steinol 110l

Cutting. Two sticks and one stick. One is the “arrow of the bow”. Two sticks are arrow plumage.

The minimum temperature is to twist counterclockwise to a lot of emphasis (“one stick”), a little stronger and the refrigerator will turn off. It is normally considered invention.

The closer to mines., the less the compressor works, which means less energy consumption.

But! Too at least and temperature may not be enough, it will begin to “sour food”. So install it.

Middle, a day or two smaller. Suits the temperature, in a day. Two are still a little less. It became a warm in the cell, return a little back.

How to adjust the temperature in a two.Chamber refrigerator stynol with a drop system

Adjustment of equipment with a drip system is carried out after installation in the room. For stable air circulation, it is necessary to leave a small space between the sidewalls of the equipment and the rear block of the case. The parameters of the intervals are indicated in the technical documentation.

The work is carried out in the following sequence:

• Stinol refrigerator needs to be left in the room for 3-4 hours. Then the device is connected to the household electrical network.
• Setting is performed in standard models using a thermometer.
• The thermometer must be placed inside the refrigerator compartment, the temperature corrector is placed in the middle position.
• After the operation of the equipment for 2-3 hours, the parameters of the thermometer must be checked.
• With a thermometer 2 5 ° C, the equipment is considered correctly configured.
• At the next stage, the freezer is checked, it is necessary to set the temperature at least.18.21 ° C.

Temperature adjustment instructions in the refrigerator STINOL

The temperature adjustment in the refrigerator “Stinol” is performed using an electronic or mechanical device. The parameter is selected according to the technical requirements of the device and the type of product. When storing fish, meat, cheese and eggs in the chamber, the temperature of 1 3 ° C is optimal, for culinary products it is 2 4 ° C, for fruits. 6 ° C.

Useful tips

Support for optimal storage conditions depends not only on the quality of the equipment, the correct installation of the temperature regulator, but also on human behavior.

To maintain the correct temperature, you need to consider the following:

If the door is too frequent, a lot of warm air will come inside. Therefore, it will be useful to open the door less often. In this case, the device will operate in normal mode, providing an optimal temperature regime for storing products in accordance with the displayed adjustment of the thermostat. Do not hold the door open for a long time

This can lead to rapid wear of equipment and to violation of the thermal storage of products. It is important to behave correctly when turning off the electricity. The safety of products in this situation depends on how long the desired regime is maintained inside

With a closed door, modern equipment can maintain the necessary conditions for storing products for a day and a half. Therefore, it is important to open the door extremely rarely during this period. It is important to regularly control the condition of the rubber laying on the door. The tightness of the refrigerator depends on its serviceability. In case of damage or wear, it is necessary to take measures to replace this laying. It must be remembered that the conditions in the room, the time of the year, the weather significantly affect the conditions of the equipment. The warmer on the outside, the more difficult it is to work the compressor. The optimal temperature conditions for the operation of the equipment are indicated in the instructions for the operation. Typically, we are talking about a temperature range from 16 to 32 degrees. If it has become too hot, it is necessary to establish adjustment of the thermostat in such a way as to make the refrigerator mode less intense to prevent enhanced wear. It is important to control the conditions in the room. For this, you can, for example, install a stationary thermometer in it. For additional control of the situation inside the refrigerator, it is recommended to use a regular thermometer designed to work with an appropriate temperature range. If the internal conditions will not change during the adjustment of the refrigerator thermoregulator, it is recommended to call the wizard for repairs. The exact figure, which should be installed on the regulator, is determined taking into account not only the composition of the products stored inside, but also other circumstances. To do this, it is also necessary to take into account the temperature of the air in the room and the door opening frequency. Typically, the optimal regime is determined in practice taking into account all the above circumstances. For example, temperature adjustment in the atlant refrigerator requires the set regulators to provide optimal conditions taking into account various conditions on the shelves. In order to optimize storage conditions, it is necessary from time to time to do full defrosting. For this, for a short time, the refrigerator is kept disabled, and the products are kept in a cool place. At the same time, traces of icing are eliminated, and the work of the compressor again becomes more effective.

The use of these simple tips in practice will help reduce the wear of equipment and improve the conditions for storage of products.

Connecting the refrigerator

After acquiring the Steinol refrigerator, it must be left in the room for 2-4 hours in a turned off state to fill the necessary labyrinths with a refrigerant. The air temperature in the room in which the use of the unit is planned should be in the range of 16 % 32 ° Celsius.

When installing the device, it must be leveled using adjusting supports. Before the first turning on, it is advisable to wash the refrigerator inside and outside with soap solution and baking soda.

To connect the device to the electric network, you need to turn on the power plug in the outlet. In this control panel, green indicators will light up.

We pay attention! If necessary, re-connect the refrigerator to the network, do this no earlier than 4-5 minutes after disconnecting.

Frost in the refrigerator Stynol. What temperature should have a refrigerator compressor

To understand the reasons for heating the compressor, you need to try to figure it out in the principle of the operation of refrigeration units. And its principle is to pump heat from one place to another. That is, from the freezer to the outside. It is also necessary to know to what temperature the compressor can be heated, and what is the reason for its overheating.

In the classical model of the refrigerator, a compressor unit, absorbing a freon from the evaporative chamber, filters it and sends it to the capacitor. The gas is very hot. Cooling in the capacitor, Freon goes into a liquid state, cools the refrigerator, and then, returning to a gaseous state, returns through the evaporative camera to the capacitor. This is repeated until the temperature set by the thermostat is reached.

In other words, the refrigerator compressor should work almost in extreme conditions.For example, in order to reach a temperature of 5 ° C inside the refrigerator and about 18-20 ° C in the freezer, the compressor must do some work, compressing the refrigerant With high pressure. At the same time, the compressed freon reaches a high temperature, which he partially transfers to the compressor, and partially leaves it in a special lattice heat exchanger. By the way, the latter accumulates the heat released by the electric current passing through the windings of the compressor device.

Remember that the permissible temperature of the compressor in working condition can be from 50 to 60 s, but not higher than 90 s. With a strong wear of the refrigeration unit, these indicators can be slightly higher.

Heating the compressor to the temperature at which the protective relay is triggered, in just a few minutes it may indicate damage to the engine winding. In this case, it is necessary to produce Full replacement of the compressor.

Typical reasons for overheating

• The temperature sensor that does not turn off the compressor after reaching the given temperature is faulty.
• With increased loads on the unit, especially in the summer heat, when its timely cooling is problematic.
• The heat exchanger is faulty.
• Cooling element leak (freon).
• Refusal of the backlight indicator.
• The motor is worn out.

Also, the reasons for overheating of the compressor include non.Compliance with the operating standards of the refrigerator installation specified in the installation instructions:

• Doors without need not open for a long time.
• Do not put the refrigerator close to the walls so that the circulation of cooling air is not disturbed.
• Do not put a cooling unit close to radiators.
• Do not expose direct sunlight refrigerator.
• Do not put hot food.
• The refrigerators are overloaded with foods.
• The freezer did not defrost for a long time (due to the lack of an automatic thast system of Nofrost).

Signs of a fault of a refrigeration unit

The main types of malfunctions, for the repair of which a professional master will have to be attracted, as a rule, are:

• The casing of the refrigerator beats the current.
• The supercharger is very hot and turns off immediately after turning on.
• Snow cap quickly forms on the back walls of refrigerator chambers.
• The motor-compressor does not turn on.
• There is no cooling (air in the refrigerators heats up, not cooling).

Of course, there are failures in the operation of refrigerators that are easily eliminated (the light is burned, it burns, water accumulates in the lower part of the refrigerator, etc.), but there are those that should be paid to special attention: to call a master who understands the qualified and eliminates all the malfunctions. So you should not just sound the alarm with a hot compressor. It is better to see and listen to his work, and if there are no other serious signs, then your refrigerator is serviceable for.

You noticed that your refrigerator stopped freezing? This is one of the most common malfunctions that can be associated with a breakdown of completely different parts of the mechanism, so when diagnosis, all the nuances should be taken into account.

Let us consider in more detail the cases when the refrigerator does not freeze, but the compressor is hot:

Most likely, the thermal protection has burned out that the engine does not overheat and does not burn out. In this case, you will have to completely change the starting relay, because the repair of this part is not carried out.

Damage to the thermal attewer. The device can transmit incorrect information to the device control unit, this leads to similar results.It will not work to repair the thermostat either, so the part will have to be replaced with a new.

Freon leak. When the system works according to the old algorithm and almost unchanged, but the temperature in the chamber remains high, it should be said about the leakage of the refrigerant. In this case, the refrigerator must be added by freon, and its performance will return back to normal.

Damage to the compressor motor. This is the most serious problem that occurs during the operation of refrigeration equipment, so only a competent and experienced specialist who will not jeopardize the entire mechanism should be repaired.

What to do if the refrigerator does not freeze, and the compressor is hot?

The first thing to do is unload all the products from the camera and defrost the refrigerator. At the end of the defrosting, turn on the device again and check if the situation has changed. If this does not help, then it is better to turn off the equipment and call the repair master. It is better not to leave the refrigerator on, as the motor can burn out and then the repair will cost you a lot.

Useful tips

For the refrigerator to work for a long time, and the products retain the maximum benefit, you should adhere to simple rules.

• First decide what and where you want to get, then open the door. This will avoid long searches. Due to the long-open door, a significant warming of the internal space occurs, which does not benefit either technology or products.
• Do not force the refrigerator to work at the limit. The optimal parameters are indicated in the instructions. It is better to set the values ​​in these ranges.
• The refrigerator should be put in order not only for the sake of cleanliness, but also to extend his life. Spoiled products, food residues can create an unhealthy environment. Ice frozen on the walls, and even more so on tubes with a refrigerant, reduce the efficiency of work and create an additional load on the motor.
• Hot food sent to the refrigerator, firstly, creates a local “temperature shock”, for example for a shelf, which can lead to its destruction. Secondly, this also creates an additional load on the device, because he needs to urgently level the temperature inside the chamber.

Compliance with these simple rules will allow you to save the refrigerator in working condition as long as possible.