How to assemble sections of the heating radiator

Installation and installation of heating batteries in a private house. from choosing to a step.by.step guide for the device

Private houses differ from multi.unit the presence of an autonomous heating system, the functioning of which does not depend on a number of external factors, such as the frequency of the heating season and the stability of the behavior of the coolant in the circuit. Autonomous heating is equipped with the owner of the house from scratch, and at the same time you have to think through a lot of nuances. for example, choose the most suitable batteries and their connection scheme. This article will talk about how to install heating batteries in a private house.

When selecting components for the autonomous heating system, it is necessary to take into account its features and the desired characteristics. Not only operation will depend on the selected elements, but also the installation of heating radiators in a private house.

Heating systems of private houses differ from centralized by the following qualities:

  • Firstly, operating conditions are more favorable-for example, the pressure in local heating is an order of magnitude lower;
  • Secondly, the quality of the coolant in private houses is always at a higher level;
  • Thirdly, there are no significant pressure drops, and the probability of a hydraulic jacket is practically absent.

There are a lot of radiators that can withstand such operating conditions, so you will have to spend some time on the choice of the best option. However, if you simplify the choice of radiators to the limit, then the best option would be products with the best combination of heat transfer, price and quality.

The following types of batteries are distinguished depending on the design:

  • Panel and sectional. The cheapest type of batteries, characterized by a fairly high heat transfer and relatively small sizes. Radiators do not present any requirements for the connection scheme.
  • Tubular. Technical characteristics of tubular radiators practically do not differ from the previous type, but the cost is much higher. Increased cost is determined by good visual qualities of tubular products and the ability to use radiators as dryers.

However, much more often radiators are classified according to the material of manufacture, depending on which the following types are distinguished:

  • Aluminum. A fairly popular option that is perfect for use in private houses. The main advantages of aluminum radiators are good visual qualities and high heat transfer. It takes a little time to warm up, but such radiators cannot hold heat. The cost of aluminum products varies in a fairly wide range depending on the manufacturer and characteristics.
  • Bimetallic. This type of radiator, as the name implies, consists of two materials. Due to this, it is possible to create a product with the optimal combination of characteristics. in particular, bimetallic batteries perfectly withstand pressure drops and are not given corrosion. The cost of bimetallic products is quite high, so they are not very popular among owners of private houses.
  • Steel. Steel batteries are distinguished by good heat transfer and good decorative properties. Simple steel batteries are cheap, but quickly fail due to the effects of corrosion. Stainless steel options are characterized by increased reliability, but are also an order of magnitude more expensive.
  • Cast iron. In the arsenal of the advantages of such devices, high wear resistance, due to the high thickness of the cast iron and its resistance to corrosion, as well as the ability to work at high temperatures and pressure drops. Cast iron batteries are highly inertia. For normal operation, such products must be cleaned every year.

Before installing heating radiators in a private house, you need to choose the best option for radiators that will correspond to specific operating conditions.

The location of the radiators

The choice of place for installing heating radiators is mainly carried out depending on the specific features of the building. In particular, it is necessary to take into account the location of the windows. in most cases, the installation of heating batteries in a private house is performed precisely under them. The absence of batteries in these areas leads to unhindered penetration of cold air to the lower level of the room.

The standards indicate that the most effective protection against cold hit through the windows is achieved if the battery width is at least 70% of the window itself. The inconsistency of the size of the radiator does not allow him to demonstrate high heat transfer and will allow the cold to enter the room where it will cause condensate formation.

When performing the installation of radiators in a private house, you also need to pay attention to ensuring that the window sill does not close them completely. so that the movement of warmed air masses is possible, they need to create suitable conditions. The best option will be the timely design of the heating system, taking into account the features of the installation of radiators and the use of protective screens that provide efficient heat transfer and protect residents from random contact with the battery.

If the house is in the region, which is characterized by a harsh climate, it may be necessary to install radiators near the front door, and it is advisable to minimize the distance from it to minimum. All radiators need to provide simple access so that if necessary, you can quickly intervene in their work.

Preparation for work

It should be noted that the sections are sold in a piece, so you can always buy the required amount. It is important to take components of one manufacturer. Then you can be sure that all elements will be the same and outwardly and from the point of view of the working parameters of the assembled radiator.

  • Divorce key with a range of work from 0 to 35 mm.
  • Key for radiators. You can use homemade, but for its manufacture you will need to make a lot of effort. Better to buy ready.made.
  • Paronite gaskets. 2 pieces for each added section. One for each nipple. Installed in the center of the thread.
  • Nipples. 2 pieces for each added section. Often come in the kit when selling.

We get to work

It’s time to check the quality of your work. If cranes are installed in front of the radiator, then you can open them. Water will fill the battery and you can inspect the joints. If you do not have a leak, then you coped with work “excellent”!

Installing bimetallic radiators with your own hands, oh can be read at the link.

Installation and connection of aluminum batteries

Connection of aluminum radiators begins with the markings of areas for mounting brackets. When choosing a place for installing radiators, the following points should be taken into account: the distance of the device from the windowsill should be 10 cm, from the floor-about 12 cm, and 3-5 cm from the wall. Compliance with these distances will achieve the most efficient heat transfer as possible.

To additionally reduce the level of heat loss, it is worth considering a number of points in advance: the radiator can be installed in a special niche or closed by a decorative screen. In addition, the heat transfer is affected by how aluminum radiators are made to the heating system pipeline.

Having thought out all the nuances of the installation of radiators, you need to fix the bracket on the walls, to which the radiator is suspended. Brackets should be located so that their hooks are exactly between the sections of the radiators. The installed radiator must be checked for alignment and, if necessary, adjust its location with brackets.

The last stage of work is the connection of aluminum batteries to the heating system. To do this, take a pipe key and connect to the radiators with the eyeliners. Controversial reinforcement is installed only on the lower supply pipes. With each filling of radiators by the coolant, it is necessary to very smoothly open the shut.off valves so that there are no hydraulic boards in the system.

Rules for the installation and operation of aluminum radiators

Pipes can be brought to the radiator on both one and two sides. If the pipeline is summed up only on one side, then it is better to refrain from using long radiators. With versatile eyeliner, you can use radiators from 24 sections, and in systems with natural circulation of the coolant. no more than 12 sections.

On each eyeliner’s eyeliner, a shut-off-regulating reinforcement should be installed, which makes it possible:

  • Set up the temperature regime in each individual room;
  • Disconnect one radiator for prevention or repair without stopping the entire heating system.

During the operation of aluminum radiators, a number of rules must be observed:

  • The radiator cannot be completely disconnected from the system, except in cases requiring repair or preventive work;
  • It is forbidden to process aluminum radiators with “metal” colors;
  • For cleaning the radiator, abrasives and aggressive chemicals cannot be used;
  • It is prohibited for more than 15 days a year to let water from a system with aluminum radiators for more than 15 days.

It is recommended to clean the batteries before each heating season.

Tools and materials for assembling radiators

To add new batteries, some tools and materials will be required:

Рено Кенго 2 ЗАМЕНА РАДИАТОРА ПЕЧКИ! Kangoo 2 heating radiator change. Citan. Kangoo 3. Master…

  • radiator key;
  • nipples that are used in the extension of radiator sections;
  • pipe key;
  • sandpaper;
  • plugs with right and left threads;
  • Paronite or similar intersection pads.

You can buy such devices in any construction store. They will cost relatively inexpensive.

A step.by.step assembly process

The connection of aluminum heating radiators is performed in 3 sequential stages.

Preparatory actions

Living in the apartment will have to coordinate work with the management organization. To do this, contact the instance and make a statement. If we are talking about a private house and an autonomous system, approval is not required.

  • Drain the water from the system completely;
  • Remove the aluminum radiator from the wall;
  • Inspect the radiator for the presence of pollution, damage and remove them, if necessary;
  • Make sure the operability of the battery connection to the heating pipe (if there is a scale, clean it with an sandpaper).

Combining sections

Take the aluminum heating radiator and put it on a flat surface. The front side should look at you.

  • Remove the plugs on the end connecting departments.
  • Put the gasket on the nipple.
  • Insert the nipple into the collector of the aluminum radiator and scroll it a couple of times.
  • Connect the section ready for assembly with the remaining part of the nipple.
  • Take the key and carefully tighten the nipple. Since at the ends of the thread element is applied opposite, simultaneous tightening of the sides occurs. The sequence of the connection is as follows:
  • In a more massive part of the battery, you need to wrap for one and a half turn of 2 nipple;
  • Then move the second part of the battery and enter the nipples into the threaded flanges before touching,
  • After that, the radiator key in the right direction (in the same thing that was wrapped the nipples initially), wrap one nipple for one and a half to two turns, then the other nipple for three or four and so on until a complete dense connection.

Twist the nipples at the top and below the same number of times. Otherwise, a skew will be obtained. Count the turns.

Before installing an extended section, make sure the tightness of the compounds. To do this, pour a little water into the aluminum radiator and leave for a couple of hours. If there was no leakage, everything is done correctly.

Checking the operability of batteries

Be sure to make a final test of the heating system. Start mounting the battery, firmly connecting it to the pipe using a pipe key. Make sure the connection errors and run the coolant into the system.

The first check is carried out under slight pressure to identify possible leaks. When the leak appears, you will need to turn off the feed and eliminate the problem.

The next stage is the supply of the coolant under the usual pressure. Now you need to leave the liquid in the system for a couple of hours. After time, check the sections of the connection and make sure that everything is in order.

Independent installation of sectional heating batteries

Before installing the radiator, the surface of the wall that will be behind it must be plastered and putty. After that, it is recommended to stick a sheet of foilizol, corresponding to the size of the heating device.

During the final finish, reflecting the surface can be poured with wallpaper, painted or laying with tiles. the foil will still provide heat to the direction of the living room.

Necessary tools and additional materials

To perform installation work on installing sectional bimetallic heating radiators, it is necessary to prepare:

  • Divorous wrench;
  • Peorator or shock drill;
  • Popov’s pipe key (ass);
  • building level;
  • roulette and pencil;
  • radiator key with an end spatula 24 mm;
  • a set of end plugs with a plug and a crane of Maevsky;
  • ball crane ½ inch with a detachable connection, outer and internal threads;
  • a crane-regulator for a thermogol;
  • radiator gaskets;
  • Hitter Len (Packla);
  • plumbing silicone or packing paste.

Depending on the installation method, the elements of fasteners can be hinged or floor. In the first case, they need 4, in the second. 2.

Refining sections of radiators

Before installing the battery in place, it is necessary to assemble a device with a calculated number of sections. The factory equipment provides for sets of 10 elements. Therefore, in most cases, you will have to separate or add a few pieces. This is done using a special radiator key, the length of which is at least 8 sections, and the width of the end blade is 24 mm.

Look at the threading direction on one of the end openings of the radiator. Insert the key inside so that the key blade is in the junction area between the disconnected sections. Take the key to the back from the thread direction. The moment of separation of elements is usually accompanied by a click.

Adding the removed sections to another kit is made in the reverse order.

Options for connecting the heating device to the wiring pipelines

After the re.launch is performed, traffic jams, shut.off valves and a crane for producing air are installed on the battery. A way to connect a bimetallic heating radiator in an apartment is determined by a pipe wiring system that can be:

In the first case, shut.off cranes are installed on both sides of the device, in the holes of the lower plugs, and the Maevsky crane to the upper long.distance along the coolant. The name of the second binding version determines the installation of reinforcement in the upper and lower cork located diagonally radiator.

A unilateral connection scheme is used for single.pipe vertical risers of multi.storey buildings. In this case, the taps are mounted on top and below on one side of the battery.

Installation of a bimetallic radiator on the wall

After the sections and the installation of shut-off-regulating reinforcement, you can proceed with the installation of the heating device for the place intended for it. over, the procedure for your own hands is as follows:

  • measure the distance from the lower edge of the section to the center of the upper nipple connection and add 100-120 millimeters to this value;
  • apply a mark on the wall in height of the measurement made;
  • Draw a horizontal fishing line for a trimmer, passing through the previously taken mark;
  • draw the position of the middle of the window on this line;
  • Make a measurement between the nipples of the penultimate sections of the radiator sections, divide the result by two and set aside on the horizontal line in both sides of the center of the battery;
  • measure the distance;
  • From the received marks vertically, set the distance corresponding to the measurement between the centers of the section of the section (usually 500 or 300 mm);
  • Sprinkle 4 holes according to the obtained marks, insert plastic plugs into them and tighten the hinged mounts along the thread;
  • hang the radiator on the installed supports.

After that, it is necessary to measure the distance from the battery to the wall and check the horizontal position of the upper plane of the device with the level. If necessary, the fasteners should be unscrewed or twisted, and the horizontal installation should be adjusted by bending up or down the installed supports.

Floor installation of heating batteries

This type of installation of radiators is used in the absence of a strong carrier wall. This happens with the design of window openings to the level of the floor, window fences, or surface lining with plasterboard slabs with significant removal (more than 200 mm) from capital walls.

Floor fastenings are a metal supporting structure in the form of the letter “H” with the lower transverse bar for screwing to the line. They are made in two versions:

The easiest way to install a heating device without fixing on the wall is done as follows:

  • Take 2 fasteners and just put them on the below on the radiator;
  • Put the device along with the fasteners to the place of its installation;
  • Ask the assistant to hold the battery and make marks on the floor through the holes in the lower bar;
  • Remove the fasteners, plunge the holes and fasten the support to the floor on the dowels.

It is recognized that the floor installation of radiators is less reliable than a hinged. But there are options that this will be the only possible solution to ensuring the heating of the room. Only warm floors can serve as an alternative.

Connection sequence

When choosing a connection method, the type of device is taken into account, as well as the strapping of the heating radiator. Since there are many installation options, it will not work to describe them all in one article. That is why we will describe how to correctly install a sectional aluminum heating radiator.

Necessary components

For work, prepare various components:

  • In the factory, the collectors made a left or right thread on each side. If you need to add sections, then adapters will be needed to go to right.sided thread.
  • The plugs with an external threaded cut are needed to close two unused inputs. The threads of the plug should correspond to the adapter.
  • To lower the air from the radiator on the upper manifold, instead of the plug, the maevsky crane is installed.

All components are sold both separately and in the kit. To make it easier to replace and repair the radiator in the future, when connecting it is installed, ball valves are installed, but it is much more profitable to use an American that has a uniform nut. In some cases, instead of ball cranes, a direct or angular.type temperature regulator is mounted.

In the process, you will need a sealing pasta, a divorce key, a pacly, an open key, a peorator, as well as the construction level. In addition, prepare a pencil, roulette and square.

How to remove and replace a central heating radiator for decorating.

Installation process

The heating device is installed in the following order:

  • Mark the wall at the installation site of the unit. Drill holes in the wall and fix the brackets on it. All fasteners are installed using the level.
  • Now they begin to collect the battery. To do this, it is laid on a workbench. Particularly purchased components purchased earlier.
  • The heating device is hung on the brackets in the wall. After that, check the correct installation of the device in the vertical and horizontal plane, as well as the location of the strapping elements.
  • On the tap thread on the opposite side of the unit nut we fix the parts to connect the unit with the heating contour of the house. If polypropylene pipes are used, then this will need fittings. When fixing to a steel pipeline, a threaded.
  • I join the heating device with the highway.
  • After the insertion is performed, sealing gaskets are laid in the unit nuts on the American taps. The device is connected to the feed and back pipeline.
  • At the final stage, the system is crimped to check the tightness.

Adding sections to aluminum radiator

If you need to add a few sections to the device, the question arises of how to combine aluminum radiators. For this, the previously installed battery must be dismantled and put on the floor covered with a film by the outer side to itself.

Add sections of the heating radiator can be as follows:

  • From the ends of the issuance of collectors, we delete plugs.
  • On one side of the nipple without carving we put on a rubber gasket.
  • After that, insert the nipple into the collector and twist.
  • Now the section we plan to add is connected to the other side of the nipple. We tighten the connector with the key. During this process, both sides will be simultaneously pulled up, because the opposite carving is performed from each of them. The connection place is twisted as much as possible.
  • We check how hermetically the sections are connected. For this purpose, you need to pour slightly tinted water into the device and wait a few hours.

Advice! To avoid distortions of the device, the nipples on the lower and upper manifold we tighten the same speed. For this, they must be considered in the process of rotation.

Connection of bimetallic heating radiators among themselves

The assembly of the new heating system is carried out taking into account the power of all devices. With proper calculations, the radiators and the pipeline serve the right amount of heat. But if heat losses are not taken into account due to large windows, door openings or small insulation of the house, you have to build up batteries. High.quality heating radiators allow not only to supplement, but also to remove the elements. Consider how to combine bimetallic radiators among themselves, which will be required to do your own hands.

It is necessary to supplement the number of sections only with a violation of the temperature regime in the room. This is due to a decrease in the heat transfer of the unit, for example, if errors are made in the calculations. But it often happens that new windows are cut out in the house, additional doors are equipped and an insulating layer is obsolete over time. in these cases, the level of heat is also reduced and the sections must be added.

ЗАМЕНА РАДИАТОРОВ | Купили убитую квартиру | Бюджетный ремонт старой квартиры своими руками

Note! Before installing additional elements, you should check the operation of the boiler. Sometimes interruptions in heating occur due to impaired functionality, the formation of deposits within the highway.

You should know that not all bimetallic heating devices can be joined, two types of products are offered on sale:

  • Sectional. These are devices that are allowed to integrate in highways of centralized heat supply, consist of separate sections. The assembly will not cause difficulties, as well as the extension of the width of the device.
  • Cast. Produced in whole form, without the possibility of building or decreasing the number of sections. Suitable for use in thermal systems with unstable pressure, are checked under pressure indicators of 100 atmospheres. Such devices are expensive, so you need to carefully calculate all power parameters taking into account the heat loss of the house. it will not work to change the power of such radiators.

On a note! Buying sectional batteries made of bimetallic alloy, which can be increased, the owner of the house gets the opportunity to install a separate regime in each room.

Sections building techniques in the bimetallic radiator

If the master has already encountered the assembly of the heat supply system, then the buildup of heating batteries will not cause much trouble. First you need to perform simple calculations, determining the power of the batteries, and then calculate the number of additional sections.

Advice! To calculate the power of the device, you need to take into account the heat transfer indicator of each section. the parameters are indicated in the technical passport of the device.

Tools and materials for work

In order for the assembly of the heating radiator to be carried out quickly, the master will come in handy:

  • additional sections;
  • sandpaper of the middle fraction;
  • radiator key;
  • wretched or divided key;
  • plugs. there should be 2. with the right and left threads;
  • nipples, usually come with a heating device or its section;
  • elastic gaskets for installation between sections;
  • Paronite gaskets.

It will not be superfluous to stock up on gloves and a mask. when cleaning the elements, a slight dust will be a little dust. And now more about how to connect the battery.

Phased work on the accession of battery sections

Before connecting two radiators, it is necessary to prepare a heating highway. First you need to turn off the circulation of the coolant and remove the battery. Today, all bimetallic devices are produced with equipment with a ball crane, so you can dismantle the battery even with a circulating coolant, for example, in a multi.storey building.

Important! There can not be more than 16 sections in the bimetallic radiator. If more heat is required, then two separate heating devices are formed.

Now the phased assembly of the heating radiator with your own hands:

  • The dismantled unit must be laid on a flat surface. Clean from dust and rinse from the inside to eliminate scale, deposits. It is best to flush in the bathroom, having previously covered the bottom of the bathroom with a rag.
  • Washing is performed like this. pour a special tool for softening of deposits inside the battery, then give time to act, drain the work, rinse the device from the inside with running water.
  • Check the threaded joints at the ends, the thread should be whole. If there is rust in the junction zone, growths or deposits, they need to be cleaned with an emery. Wipe the pure thread with a rag to remove possible pollution that violate the sealing of the devices.
  • Put the dry and washed radiator on the floor. It is more convenient to work if the floors are covered with a soft rag, so the devices will not beat on the flooring, they will not damage both the finish and the protective upper layer. A flat horizontal is required for an accurate connection without distortions. the slightest deviations during docking will lead to the formation of gaps, leaks.
  • Check the quality of the nipples, the thread on them and the integrity of the nests, lay out paronite gaskets. If there are chips on the threads of the nipples, and the nests are broken, the details must be replaced.
  • Put the sections among themselves so that nipples and paronite gaskets are clamped between them.
  • Carefully start twisting nipple. On the one hand, the carving part is left, and the other side is equipped with the right thread, therefore, in the process, the sections are executed uniformly.
  • The work is performed by the radiator key, which will help not only to comprise the heating radiators to each other, but also to disassemble them in order to disconnect unnecessary sections. To reinforce the nipple is spinning the key to the other side.
  • Having pulled the nipples a little, check the evenness of the joint, tighten the nipples to the strength to the same number of revolutions.

Important! The number of nipple turns should be carefully considered in each section in order to prevent the radiator distortion.

Knowing how to increase the heating battery, the master will always be able to ensure high.quality heating of the premises, but only in the case of using sectional radiators. After connecting the parts, the device must be checked for tightness. This can be done by means of a bay in a tinted liquid battery. Close the plugs, leave the device for several hours, sometimes it takes a day for testing, and then inspect the joints. if there are no leaks, then the assembly is carried out correctly, install the radiator in place, start the system into operation.

Advice! If it is necessary to install the battery in the heating system immediately after building, soap water is used to check sealing. Wet the sponge, wipe the joint zones. if there is a leak, then the soap will foam.

Radiator connection schemes to the heating contour

There are several schemes on how to connect heating radiators in a private house. With a single.pipe system used in multi.storey buildings, each radiator is inserted into a single pipe along which the coolant moves and is assigned back. Water passes sequentially through all the batteries, gradually cools.

With a two.pipe system, each of the radiators is based on two pipes. for serving and returning to the reverse outline. Risers are collectors, radiators are parallel to them in parallel. In this case, the dependence of the heating temperature on the location of the battery is minimized.

Diagonal connection

The diagonal connection of heating radiators refers to two options:

  • With double.sided connection with the supply from above, a more effective heat return occurs. Water does not meet in its way of resistance, passes through the upper manifold, vertical channels, warms the radiator evenly over the entire area.
  • With bilateral connection with the supply from below, loss of efficiency is up to 20%. The coolant is not able to freely penetrate into the distant sections of the lower supply collector, so due to the difference in densities, it selects vertical channels close to the entrance. With a heated top below, stagnation is often formed.

The second scheme is used very rarely, the first is more successful.

One.sided with the upper and lower feed

Such installation of heating batteries is organized according to the principle of upper and lower feed:

  • At the first, the coolant is transmitted to the top point of the riser, all the radiators on the floors are sequentially passing. The flow goes from top to bottom.
  • To simplify the system and saving materials, a scheme with a lower presentation is used. In this case, radiators are installed on the ascending pipe, the flow goes from the bottom up. In this position, the temperature difference is more tangible.

On a note! For a single.pipe riser, a bypass is required. a jumper for connecting the radiator connection pipe to the riser. This scheme is characterized by the simplicity of the device, but the difficulty of ensuring heating on different batteries.

Double.sided with the upper and lower feed

Connecting heating radiators in a two.pipe scheme is very popular in autonomous heating systems of private houses. It allows you to hide the pipes under the floor, make them as invisible as possible. But with this approach, heat transfer is lost, efficiency decreases by 10-15%.

With a lower supply, heat is given better, the spread of water through vertical channels is due to the difference in density. With the upper feed, there is a risk of lower warming up the upper part of the battery.

As the location of the radiator on the wall affects its effectiveness?

In addition to the correct connection of heating radiators, when installing it is necessary to take into account the place of their position. The rules for placing the battery on the wall, taking into account the structures and elements of the interior, must be observed.

Under the window is the most typical location of the battery. The radiator gives heat, the convection flow creates a heat curtain, which makes it difficult to penetrate from the windows of cold air. The maximum battery efficiency is observed provided that its length is 75% of the width of the window opening.

The radiator must be installed directly in the center with a permissible deviation in both directions of 2 cm. A distance of 100 mm is withstanded from the windowsill, otherwise an obstacle is created for air flows, the efficiency of the battery falls. The height of the lower edge from the floor is 10-12 cm. If the distance is less, it is difficult to clean under the radiator, convection is difficult. If the height is larger, the floor will remain cold. From the wall the radiator is 20 mm brackets. With a decrease in the lumen, convection is disturbed, a lot of dust appears.

A wide window sill, dense cakes, casings, decorative facade screens can lower the effectiveness of heating. They make the interior beautiful, but lower the heat transfer.

Heat loss depending on the location:

  • The installation on the wall is open, under the windowsill. the effectiveness is equal to one.
  • Window sill or shelf completely close the radiator on top-loss of 3-5%.
  • The upper wall of the niche covers the battery on top-losses 7-8%.
  • Covering the facade with a decorative screen, but there is a sufficient clearance for convection-losses 10-12%.
  • The battery is fully covered by the facade-20-25% of power loss.

Installation of installation work: scheme

Before the start of work, the heating circuit is completely overlapped, the coolant is drained from the system. The remaining liquid helps to remove the circulation pump. Using the level, check the battery hung on fasteners relative to a horizontal and vertical position.

  • All plugs are removed from the radiator;
  • If the heating circuit is one.pipe, proceed to connect the bypass equipped with a valve. With a two.pipe scheme, the proper installation of heating radiators does not provide for the use of bypass, and for the connection, you use the drive with the valve connected to it.

The battery is connected to the heating structure, using carving. Joints seal packley or other seals. In the presence of skills, they use welding in places of docking of the drives and pipelines. Until the installation of aluminum, steel and bimetallic radiators, the factory packaging shell has not been completed from them. “How to make a decor for heating batteries with your own hands using decorative panels”.

After the installation is completed, it is still necessary to put forward a system. Similar events should make plumbing, since they have experience and they have an apparatus that it makes no sense to purchase a pair of batteries for installing a pair of batteries.

Methods for installing radiators

Способы установки радиаторов отопления зависят от схемы расположения этих приборов и бывают следующими:

Despite the latest devices that provide premises, such as ultra-light and aesthetic bimetallic and aluminum products, cast-iron radiators are still in demand among real estate owners. And although cast iron products are not distinguished by an exquisite design, the batteries remain hot for a long time, gradually passing the heat to the surrounding space.

Существуют специфические особенности конструкции чугунного прибора, которые необходимо учитывать при их монтаже:

HOW TO DRAIN DOWN HEATING SYSTEMS. GRAVITY FED. Plumbing Tips


About the author

| Denial of responsibility | Contacts |RSS