Removing soot from smooth washable surfaces
Smooth interior surfaces, like plastic on a kitchen unit or varnished furniture, are the easiest places to rinse off cinders. Such surfaces have a non-porous structure, so it is difficult for contaminants to get a foothold on them. In such situations, the soot can be washed off, using the following means:
For a hygienic procedure at home, dilute one of the listed products in warm water. Then take a soft sponge, and with gentle circular motions wash away the black plaque. You will need to change the liquid periodically to avoid a buildup of dirt.
Instructions for building a condensation dehumidifier with your own hands
The operation of an asymmetrical dehumidifier is based on a permanent exchange of air: The moist air is physically forced out of the room and is replaced by drier air from outside. Such devices are good for industrial facilities, where you have to distill significant amounts of gas. Weaknesses:
- low energy efficiency (high electricity consumption, high heat loss);
- Unable to be used in humid climates (coastal areas).

How to clean a wool cap at home
Industrial adsorption devices have a high self-made technique specialists do not recommend, as it is expensive and not designed for home use.
Dehumidifiers based on the principles of adsorption are more common for home use. The heart of the construction is the material, which is able to absorb water from the air environment. The active ingredient can be:
It is not difficult to make a self-made device according to the instructions. In this case it is important to ensure not only the absorption of moisture by adsorbent, but also periodic “recharging” of the active substance. The material must be dried, and after a certain number of cycles completely replaced with a new one.
Kit
Standard composition of an adsorptive dehumidifier:
On this basis, it is not difficult to choose elements for a homemade construction. To create a dehumidifier for the house you will need:
- two plastic bottles of the same volume;
- awl;
- A lighter (matches);
- Silica gel or other adsorbent;
- cutting tools;
- a battery-powered fan (cooler) or a USB-cable for connection to the electric mains;
- duct tape, glue gun.
The volume of the bottles is chosen based on the size of the room. For effective work, it is recommended to use containers of at least two liters.
Assembly
To create a moisture absorber for the house, it is necessary to perform the assembly in steps:
- Cut one of the plastic containers in half.
- Using an awl or a needle heated over a fire, make several holes in the bottom and the cork.
- You need to turn the top of the bottle with the cork down, insert it into the bottom.
- In the obtained funnel, fill in the adsorbent.
- The second bottle must be freed from the lid, cut off the bottom.
- Departing 10-12 centimeters from the bottom of the tank, you need to fix the fan (you can use a glue gun or double-sided adhesive tape), so that when it blows down (to the cut).
- In conclusion, you need to connect the two bottles (put the pipe with the cooler on the funnel), seal the joint with scotch tape.
- To start using the ventilator, electrical power must be supplied from the mains or batteries (batteries).
The resulting device is characterized by simplicity and almost noiseless operation.
The most popular type of dehumidifiers for apartments based on condensation. the release of water from the air when the temperature drops. An example of condensation is dewdrop, which is the process reproduced technologically.
The moisture collector cools the air like an air conditioner, but without transferring heat outside the room.
Accessories
The components of the device and the principle of operation:
- evaporator is a cold heat exchanger (in it, the air is brought to a temperature below the dew-point);
- Condenser. a hot heat exchanger (it reheats the dehumidified air and vents it to the outside);
- The storage tank (condensate drains into it).
A home appliance is easy to construct from an old refrigerator with a functioning compressor. For assembly we will need:
- Unused refrigerator;
- Plexiglas with a thickness of more than 3 mm;
- Household fan with a power of 100 watt or more;
- plastic grate (pressure grate);
- fastener elements (self-tapping screws);
- sealant (duct tape, silicone);
- Tools (screwdrivers, electric screwdriver, metal hacksaw).
Of these component parts, the appliance must be assembled according to the instructions.
The Easiest Way To Clean Wood Stove Glass
How to clean the fireplace glass from soot the old method!
I recently learned a great old-fashioned way to clean the fireplace glass from soot. For a glass stove door, this method will work, too. But now it is not needed because the glass is always clean! Want to know, read How to stoke a stove correctly
Before I tell you about this simple folk remedy, I want to say a few words about other modern cleaners, which I have tried.

Dishwashing detergent, which perfectly removes grease, on the soot did not work at all. They recommended Shumanit. It’s not cheap, but I bought it for my oven. After reading the instructions, I realized that it must be used with caution, and with gloves on. I put Schumanit on the cloth and wiped the glass. no effect. Then I sprinkled it on the glass, and it flowed down, leaving a clean streak on the glass fireplace. It worked. However, running down the glass, Shumanit could easily get on the cast iron and corrode it. Replacing the cast iron is almost impossible, so you need to protect it from the dripping compound. Yes, it’s uncomfortable somehow And on the stove Shumanit got.Spattered when I rubbed. No, I didn’t like this modern product. However, quite by chance, rereading an old magazine, I came across a folk remedy on how to clean the glass of the fireplace (stove) from soot. And I want to share with you, dear reader, this wonderful free method.
How to clean the glass of a fireplace or stove from soot without having any hand tools at hand
Take a newspaper, crumple it up, wet it a little and dip it in the ashes from your stove (fireplace). Wipe the glass. When the newspaper is soiled from the soot, take a new one, crumple it up again, wet it and dip it in the ash. When the glass is clean, wipe it with a wet newspaper, then wipe it with a dry newspaper. Done! The glass in the fireplace is perfectly clean!
Firewood for the stove (fireplace). A few tips tested in practice:
The first step in removing soot is to remove the debris. Remove all unusable damaged objects from the room: furniture, books, clothing remnants and other. If the walls have managed to smoke, the finishing material from them needs to be carefully removed with a spatula.
You’ll also have to part with those objects that haven’t had time to be affected by the fire. This includes wooden furniture, windows, doors, and decor. They have the ability to quickly absorb odors, so even after removing all soot stains there may still be the smell of burning in the room. Before you put them in the trash, you should try to get rid of the smelly smell by taking them out into the fresh air or treating them with a special solution.
Soot on the stove glass. Why it occurs and how to fight it?
Soot. is unburned fuel. It appears when the chimney draught is insufficient or the wood burning temperature is too low. Universal protection against the formation of soot. Clean glass system. It will solve all problems. But even if your stove does not have this system. do not feel bad. Avoiding the following causes of soot will keep the glass clean, allowing you to admire a lively fire.
The reason you are using newspapers to light the stove
You do not want to do that. The composition of the ink used in printing is such that when burned, it instantly turns into a very “clingy” soot that settles on the glass. So you should only use clean paper to kindle the fireplace stove. But perhaps the best option is a gas burner.
Watch our video “How to heat the sauna stove without smoke”. This method is also suitable for stoves.
Solution: clean the glass with a special cleaner and never use newspapers for lighting.
Bad draft = soot on the stove pane and even some smoke. There are several reasons for the draft deficiency: 1) the furnace and the chimney have not yet warmed up, 2) the height of the chimney is insufficient, 3) there is no fresh air supply in the room.
The first problem is easy to solve. make sure that all the draft dampers are open when you are lighting the oven. If the draft is still not enough. slightly open the door. Also after firing up the stove do not let it burn for 20-30 minutes.
The second problem can be solved by extending the chimney to the necessary height. Don’t know up to which? Call us, we will tell you! Tel:. 8 (812) 605-85-05.
In the third case, if the house originally did not have intake and exhaust ventilation, the only way out is to periodically open a window to let fresh air in.
Cause Hasty setting of the stove to continuous burning mode
We have partially covered this reason in the previous point. If you put the stove on a slow burner before it and the chimney are warmed up, there will be soot on the glass. We also recommend that you do not use this mode very often. Read why in this article: https://nkamin.You can find some information in the following article: why do you put the stove in the “slow-burn” mode?
Remedy: Only reduce the combustion air supply 20 to 30 minutes after the stove is lit.
Fig. 1. Do not “love” the stove to the amount of soot on the glass
The “hotter” the wood you use, the more likely it is that soot will form. Use only dry firewood, which has a relative humidity of less than 20%. This is about 1.5-2 years of drying in a ventilated woodstove.
Cause Stove touches glass
Not an obvious cause, but also leading to soot on the furnace glass. The truth is that the temperature inside the firebox is always higher than on the glass. Because of this, the log touching the glass will “cool down” and therefore burn worse. This results in soot formation.
Solution: make sure that the logs do not touch the glass and put them as deep into the furnace as possible.
Professional soot remover
You want to clean your fireplace glass quickly, without the hassle and risk of damage? Then it is better to use a special professional detergent “Sozhnet”. It effectively removes soot, tar, soot and other types of difficult dirt. Comes in handy 0.25 liter containers. Usually this amount is enough for at least one season. If the fireplace is seldom used, even for two seasons.
- Shake the bottle thoroughly;
- Spray the cleaner on the surface. In this case, the distance between the sprayer and the glass should be at least 10 centimeters;
- Wait 5 minutes for light contamination, 15 minutes for heavy contamination;
- Wipe the surface with a dry rag, paper towel, or regular paper.
This method allows you to effortlessly keep the glass door clean during the whole life of the heater.
All ways to clean the glass fireplace door from soot
There are several ways or methods for cleaning fireplace glass from natural dirt. Is it possible to single out the most effective and efficient? Yes, of course, but about that a little later, perhaps something else will suit you.
The mechanical cleaning with a sponge and ashes (a popular method)
Although it is called a folk method, but if you think about it a little bit, something doesn’t quite fit.Please tell me that cast iron fireplace fireboxes with glass doors have always been popular? When and most importantly where did it become popular?? But come on. The essence of this does not change.
This method of cleaning is advertised by representatives of various companies that sell fireplaces. This probably shows their profound knowledge of the tradition of using fireplaces.
- Wearing gloves;
- Soak the sponge in water and wring it out;
- Apply ashes from the fireplace to the sponge;
- With light circular motions, wipe off the soot with a sponge;
- Repeat steps 2,3,4 until the surface is completely clean;
- After rinsing the sponge from the dirt wash the glass with it;
- Wipe the glass dry with a paper towel.
Using ammonia (ammonia solution)
In fact, this method, as well as mechanical cleaning with a sponge and ash, can also be considered “folk”.
Why not? In principle, ammonia has always been used to wash windows or mirrors, along with a pile of old unnecessary newspapers.
over, in my opinion, the method using ammonia is actually more popular than with the ash. But whatever you like. If you like ashes, use them in good health.
- Rubber gloves;
- A bucket of warm water;
- Kitchen sponge;
- Paper towels or a soft cloth;
- Ammonia alcohol;
- Vinegar;
- Sprayer.
- Prepare a solution: half a liter of water, 1 teaspoon of ammonia, 1 teaspoon of vinegar. Mix the solution thoroughly and pour it into the sprayer;
- Wear gloves;
- Spray the resulting solution on the entire surface and wait 2-3 minutes for its reaction with soot and soot (before applying the solution, carefully cover the floor from getting liquid on it);
- Gently wipe the glass with a paper towel or cloth;
- Repeat steps 3,4 until the surface is completely clean;
- The cleaned surface is rinsed with water;
- Wipe the glass dry with a paper towel.
Clean with a strong flame in the furnace
There is nothing to explain in this method of cleaning. Dry wood is needed. A very strong fire is started, the soot particles and smut particles are simply burned off in the flame and the glass becomes clean. There is a theoretical advantage in this whole procedure. At the same time, when creating a strong fire in the furnace, not only the space in it itself, but also the chimney of the fireplace is cleaned, which reduces the overall fire hazard level of the device.
Using special and general-purpose household chemicals
This method assumes the use of a chemical agent to clean the glass from soot. And it can be a special chemical means for cleaning fireplace glass, as well as any other suitable for these purposes, general-purpose household chemical means. The chemical cleaning is similar to the ammonia cleaning, except there is no need to prepare the cleaning solution by yourself.
Mechanical cleaning with a special scraper or knife
In case you didn’t know, just like there are special chemical cleaners for fireplace windows, there are special scrapers for removing soot, carbon black, and soot.
There is no sense to describe the process, as everything is banal: we take a scraper and scrape off the deposit from the surface. At the end of the process rinse the glass with water and wipe dry with a paper towel.
Remove the dirt with popular remedies
The most unpleasant consequence of fuel combustion is a thick layer on the glass, representing soot and smoke. Due to the fact that the basis of this plaque is creosote, which attracts particles of soot as a magnet, a simple wet cloth treatment will not help here. We have to resort to the accumulated experience, since such problems have always been encountered.
- If the glass is smoked recently, and a layer of soot has not had time to dry in creosote, it is quite realistic to use self-cleaning, which is to burn dry hardwood with plenty of air access. To do this, open the ash door all the way. The soot particles burn at high temperature, and the glass is released from the soot. But the given way is good only if you timely found out that the cleaning of the glass is required.
- Mix water and vinegar in equal parts. Pour the resulting solution into a sprayer. The fireplace door will have to be dismantled and put on a horizontal surface. A layer of newspaper is placed on the smoked areas. These newspapers are soaked in a vinegar solution and incubated for some time. Then the wet newspapers should be treated like a cloth on the glass.
Rubber gloves must be worn during the work
- Sometimes for cleaning glass, the ashes from the ash-pan are used. It is known to form an acidic environment. Chemical reactions break down the soot and the surface can be cleaned. For convenience, use a sponge. The ash must not contain dirt, otherwise the glass can be scratched. Pour the ashes on the moistened sponge and with careful movements begin to treat the surface. If necessary, the sponge should be washed well and a new portion of ash should be added again.
- Another recipe for the preparation of a remedy to clean the soot from the fireplace glass door is based on mixing ammonia, vinegar, lemon and baking soda. Preliminarily the layer of soot must be moistened, after that clean the soot with ease. It is important to remember that an increased concentration of ammonia will make a more active solution, and cleaning the glass will be easier, but ammonia will quickly volatilize, and this fact has to be reckoned with.
Cleaning the grid
After the fireplace is cleaned of soot and ash, it is necessary to clean the firewood grate well. To do this, you must take ten liters of water and dilute in it 6 tablespoons of the product, which is used to dissolve solid deposits of mineral origin. If you do not have such a composition, you can use another: four liters of water and two hundred grams of bleach. The simplest and safest will be a solution of equal amounts of vinegar and baking soda. Clean the grate from top to bottom. Apply one of the compounds to the surface and rub thoroughly with a brush.
After the soot is removed, you can begin to wash the surfaces. Take a soft sponge and warm water. Wash the chimney, firebox and grate well, as well as the door and floor around the hearth. After the procedure is complete, put all the elements back in their places.