How to clean the gorenje washing machine vertical

We clean our own drain hose in the washing machine

It should also be considered how to clean the drain hose in the washing machine. If you think that for this you just need to disconnect the hose and rinse it with water, then this is not quite as simple as it seems. After all, the connection place is inside the machine, and you still need to get to it. And here again, you will have to first recall the instructions attached to your washing machine, since all brands and models have different designs. The drain pipe can be cleaned and without removing it. Special substances are sold in stores that dissolve garbage accumulated in hoses and pipes, the seller will help you choose what you need. You can prepare such a solution of the house, pour 200 grams of baking soda into the drum and turn on the machine (without linen) to wash at 90 degrees. But if this option did not work, you still have to disassemble the machine.

The main thing is for any machine. turn off it from the network before work, block the taps, drain the water and disconnect the end of the hose from the sewer.

Now prepare the screwdrivers and choose how to get to the hose in your typewriter: through the lower panel, back cover, front or side panel.

How to clean the drainage hose of the LG, Samsung or Indesit washing machine

Remove the lower panel, disconnect the filter, put the machine to the side and disconnect the hose from the pump, and then from the machine body.

If your option is the back cover. disintegrate the drain hose from the body and unscrew the water supply hose from the valve, unscrew the bolts and remove the upper and back covers, remove the drainage hose.

, then pull out the clamp and the elastic band from the front of the case, the powder tray, remove the lower panel and unscrew the bolts, remove the door lock and front cover, light the clamps and pull out the hose.

If a machine with vertical loading, remove the side panel, light the clamps and pull out the hose.

Now let’s move directly to the cleaning of the hose. To do this, use a special non.metallic cable with a ruff at the end. First clean the hose on one side, then on the other and washed it under running water. After the procedure, the machine must be assembled in the reverse order. To check, turn on the machine without linen (you can add citric acid, against scale) to wash at 60 degrees.

Features of the drain

To understand the causes and consequences of blockages, it is recommended to get acquainted with the drain system in machine guns. All washings have one drainage scheme, and Bosch is no exception. Briefly, the process of devastating the tank looks like this:

  • The board gives the pomp with the beginning of the drain;
  • The pump begins to work;
  • The impeller starts, creating the right current;
  • water from the drum enters the pipes;
  • the liquid passes through the filter and moves to the pump;
  • The flow enters the hose and goes to the sewer.

As soon as all the water leaves the tank, the press.steast “sees” the executed drain and gives the signal about the cancellation. The pump stops, and the cycle ends.

Interesting:

  • How is the drain pump drainage pump?
  • Why doesn’t it rinse or squeeze the washing machine?
  • E7 error in Gorenje washing machine
  • Gorenje washing machine does not drain water
  • Repairing the LG washing machine with your own hands
  • ARDO chopping machine does not drain water

Each of the models of washing machines has its own constructive layout of the nodes. Some expensive specimens consist of two types of pumps: circulation and drain pumps. The circulation pump supplies water directly to the washing zone, and the drain removes it from the tank of the car. The zone where the circulation pump should be located, coincides with the location of the drain. In the modern domestic market, models with one drain pump are mainly represented. Washing machines with two pumps can be seen very rarely.

Removing the drain pump, depending on the constructive layout, can be carried out through the bottom, back or facade parts of the washing.

Whirlpool, Indesit, Samsung, HotPoint, Ariston

The drain pump on the models “Whirlpool”, “Indesit”, “Samsung”, “Hotpoint”, “Ariston” is located in such a way that working with it is most convenient using the bottom of the machine. The washer should be carefully put on the side and perform the necessary actions, removing the pump through the lower part.

Bosch

Bosch manufacturers consider it necessary to have special protection on the bottom. Therefore, this is a more difficult case. Access is made to the drain pump through the facade (front) wall of the machine standing vertically. It must be disassembled completely, including the dashboard and loading hatch.

Instructions for checking performance

Signs of deviation from normal work can be seen if you listen to the sound made by the pump. It should be even, without tangible sound deviations. Before cleaning the pump in the washing machine and check for performance at home, it must be removed.

First of all, it is required to extract the drain filter located in the lower part of the front panel under a small hatch. It opens after pushing the latches. The filter is unscrewed by thread. Do everything carefully so as not to break the details. Do not forget that you will have to drain the remaining water from the drain system.

After disassembling the elements of the machine case that limited access to the pump, the drain pump itself is removed.

Actions Peculiarities
Two power terminals are disconnected. The location is not required to remember, since at alternating current, the change in contact places does not affect the operation of the equipment.
Weaken the clamps on the pipes and disconnect the hoses from the pump housing. This must be done with the help of pliers, an awl and screwdrivers.
Remove the mounting screws of the pump case from the frame of the washing machine. Then the pump is extracted out.

After a detailed examination, the drain pump (unscrewing the fasteners) is disconnected from the snail. Then the following actions are performed:

clean, gorenje, washing, machine, vertical
  • external control is carried out for the presence of mechanical damage;
  • The presence of traces of cleaned clothes on the impeller, such as hair or pile;
  • With the help of manual rotation of the rotor, the hook of the impeller with the rotor shaft is determined;
  • The backlash of the rotor shaft in the landing nests is checked, the size of their wear.

The electric part of the pump is diagnosed using a multimeter or tester, so it will be possible to determine the problem. The dash mode is set on the device, and the control wires are attached to the metal contacts of the pump. Any three.digit number on the scale of the device means the norm. The values ​​of “0” or “1” signal the cliff in the chain.

Checking the serviceability of the electric part can be performed by connecting special contacts from the network to the pump. Thus, tests are tested to identify the problem and find out if the pump is working when feeding on the engine. Analysis of faults allows us to conclude that the repair or replacement of the drain pump.

Where is the pump

Some models of machines differ from each other in structure. Depending on the brand, the pump should be sought in various places. For disassembling and eliminating the blockage, you will need the following tools:

Also prepare the container where the water will merge in advance while you clean the pump.

You can facilitate the dismantling procedure by looking into the instructions. It indicates where the pump is located, after which you can act.

Before starting the dismantling of the pump, you need to drain the remaining water and clean the filter.

  • Disconnect the washer from communications.
  • There is a small hatch on the basement (under the front panel). Squeeze the latches of the hatch cover.
  • Twist the filter counterclockwise.

It happens that the filter refuses to get out. Sometimes the manufacturer additionally fixes it with a screw. Then you need to twist the screw, and then the filter. Substitute the container and drain water, clean the filter.

How to clean the pump correctly

The procedure for cleaning the pump is that in the pump you will need to carefully clean up one part. impeller. To fully rinse the impeller, it will also have to be dismantled.

The dismantling of the impeller is extremely simple: using a screwdriver, you need to unscrew the screws that connect the two parts of the pump together. When you disconnect these parts, you will see a small head (photo). This is the impeller. When the unit works, this head rotates and water drainage occurs.

Clean the head of pollution, thread, hair, fiber of wool and other garbage and wipe the inner snail of the part. Upon completion of the procedure, collect the pump, install it in place, also collect and correctly fix the other removed parts. When the device is completely assembled. conduct a control washing. If the water will flood and merge normally, and when working the device will not hear noise and knocks, then you did everything right.

The main signs that the pump was clogged

The first thing that happens to the washing machine when clogging the drain filter is during washing the water enters the drum very slowly, sometimes it does not pump at all at all.

The second sign of a malfunction is strangers, buzzing sounds, sometimes a deaf hum, coming from a machine during a water set for washing or rinsing. There is also no drain of dirty water, it is not excreted out.

Important! There are other reasons why the water will not merge. the drain hose is transmitted or the drain hole was blocked at the bottom of the centrifuge tank.

Whether the types of pumps differ depending on the brand of the washing machine (Whirlpool, Indesit, LG)

In washing machines, manufacturers use two types of pumps. simple and circulation. The first is found in old models or budget options (Deu). The circulation type of pump is installed in most units of popular brands. Whirlpool, Indesit, LG. The only nuance is the location of the pump.

In the washing machines Samsung, Ariston, Candy, Ardo, LG, WhirPool, Indesit just turn the device (“lay” on the side panel), unscrew several screws and remove the back cover. Siemens, Bosch companies have complicated the task of dismantling the drain pump and replacing it with a new. To carry out the procedure, it is necessary to remove not only the rear panel, but also the front, as well as the control panel.

What actions need to be performed to remove the pump through the bottom of the device

Find out where the pump is located in the washing machine, you can by the location of the drain hose. In most models of Washing machines, the pump is located at the bottom of the device.

If it leaves the bottom, then, to clean the part, you need to remove the lower panel. To do this, you need to turn off the device from the power supply, lay to one side, remove the lid from the bottom.

Then loosen the clamps of the plastic drain tube with pliers and remove it from the rubber laying of the pipe. Then weaken the clamp attachment of the pipe to the pump chamber, turn off the pipe from the fitting.

Next, it is necessary to weaken the clamp, disconnect the plastic tube of the pressure system and the pipeline fitting. The next stage is the weakening of the clamp fastening of the pipe to the tank. In parallel with weakening, it is necessary to twist the stretch screw. The procedure completes the process of disconnecting the pipe from the tank.

Reference! When cleaning the drain pump, you need to check the condition of the rubber gaskets. If they are loose, have a damaged structure, then in order to avoid breakdowns, it will be necessary to replace them.

How to remove the pump through the facade part

In the models of manufacturers AEG, Bosch, Siemens, access to the pump is located in front, on the facade part. behind the capacity for detergents. To get to the pump, you need to remove the tray, then unscrew the self.tapping screw that is under it. Next, you need to drain the remaining water through the filter located at the bottom of the unit, after which it is necessary to remove the pump for further cleaning.

How to remove the pump through the back wall of the washing machine correctly

Behind the back wall, the drain pump is located in machine washing machines Zanussi, Electrolux. To remove the pump, you will need tools: flat and cross screws, a wrench, a bowl or a bucket for draining water. Next, you need to follow the instructions:

  • Disconnect the device from the power supply network, block water access.
  • Disconnect the drain hose.
  • Turn the machine so that it becomes on the side, remove the panel with the screwdrivers.
  • Drain the remaining water into the container, slightly turning the machine to the side.

After that, you need to unscrew the pump, disconnect the pipes from the plum and filter hose. The final stage. cleaning the pump.

Dismantling of the pump through the bottom of smoke

This design is characteristic of Whirlpool, Indesit (Indesit), Samsung (Samsung), LG, Ariston (Ariston), Beko, Ardo, Candy. Access to the pump is considered the most simplified.

  • To remove the pump, you can reject the washer back. But if there is no one to hold the equipment, it is better to put it on the side. Pre.check whether there is water in the powder receiver.
  • If the bottom of the car is closed by the panel, unscrew the screws and remove it.
  • Having picked up to the pump, weaken the clamps of the pipes and disconnect them from the pump body.
  • Disconnecting the entire wiring and unscrewing the fasteners, take out the pump.

After dismantling, the part needs to be cleaned. Read about this below.

Dismantling of the pump through the bottom of smoke

This design is characteristic of Whirlpool, Indesit (Indesit), Samsung (Samsung), LG, Ariston (Ariston), Beko, Ardo, Candy. Access to the pump is considered the most simplified.

  • To remove the pump, you can reject the washer back. But if there is no one to hold the equipment, it is better to put it on the side. Pre.check whether there is water in the powder receiver.
  • If the bottom of the car is closed by the panel, unscrew the screws and remove it.
  • Having picked up to the pump, weaken the clamps of the pipes and disconnect them from the pump body.
  • Disconnecting the entire wiring and unscrewing the fasteners, take out the pump.

After dismantling, the part needs to be cleaned. Read about this below.

How often to clean

A filling filter, unlike drain, does not require regular cleaning. Clean it as it worsens the water supply to the smell. Noticed that the machine has become poorly and slowly gaining water, then do it clean it.

There is no time to mess with the washing machine or prefer to trust the repair work to professionals? Contact us with service. The master will arrive at the house within 24 hours after calling and clean the entrance filter in 15-20 minutes.

The service belongs to the category of simple repair, so it costs inexpensively. from 1000 to 1900 detailed for cleaning the filter, depending on the brand of the cm, are presented below in the table.

We suggest you familiarize yourself with how to clean the pan from the crocheted inside at home: how to clean the enameled bottom from the burning, how to wash from burnt fat

Mark of the washing machine Price
Departure of the master Is free
Bosch washing machine 1200
Washing machine Indesit 1000
Samsung washing machine 1200
LG washing machine 1300
Ariston washing machine 1000
Candy washing machine 1100
Electrolux washing machine 1300
Washing machine Zanussi 1200
Washing machine Miele 1900
Washing machine Whirlpool 1400
Beko washing machine 1000
Siemens washing machine 1400
ARDO washing machine 1400
AEG washing machine 1300
Brandt washing machine 1500
Atlant washing machine 1000
Gorenje washing machine 1300
Washing machine Hotpoint Ariston 1300
Another brand from 1000

The price is given for cleaning. The cost of a new filter, if it is required to replace it, are included in the account of additionally.

According to the standard schedule, the masters serve customers on the same day or the next. If you are convenient for another date, report this when applying. We will come to the call when it is convenient for you.

Carry out filters every 2-4 months, depending on the operating frequency of the washing machine. When using the unit daily, do cleaning monthly.

In the absence of timely care, a contaminated filter can cause the following problems:

  • violation of the drain of water from the tank, which prevents the normal operation of the unit;
  • the appearance of an unpleasant odor due to the propagation of bacteria in accumulated garbage. A bad aroma can proceed from the tank, drum and switch to linen;
  • Damage to the drain pump. The garbage from the filter is able to damage the pump or blades of the impeller, which will lead to the need to repair or replace the part.

The procedure for cleaning the drain and flood filters varies. In the first case, the procedure will not cause difficulties and take a minimum of time. When cleaning the drain compartment, you will have to work a little to effectively remove all the pollution. But if you follow the step.by.step instructions and all the recommendations, cleaning will not cause difficulties.

  • Disconnect the unit from the mains and disconnect the water set hose.
  • With the help of pliers, carefully remove the filter. It is a small metal net.
  • Remove pollution using an old denture. Do not use aggressive chemicals. To clean a sufficiently warm soap solution.
  • Thoroughly rinse the filter grid and wipe it.
  • Install the filter in place and connect the hose.

The filter is located on the back of the washing machine and protects it from garbage from the water supply. To clean it, it is necessary to block the water, unscrew the hose and remove the filter set

To clean the filter of the washing machine, turn off the unit from the mains and water supply. This is done for safety purposes so as not to get a shock and do not fill the floor with water if you have to move the unit.

Prepare the necessary tools and auxiliary objects: screwdriver, pliers, a sexual rag and a shallow container.

The procedure for cleaning the drain filter in the washing machine:

  • Find the filtration system. Remove the decorative hatch by pushing the latch screwdriver. You can remove the false panel by moving it a little to the side or pulling it over.
  • In the filtration system, there is always a little water that will result in the part after removing the part. To avoid the flood, place a low container under the hole or put the floor rags. Some washing machines are equipped with an emergency hose or a special gutter to remove water.
  • Unscrew and pull out the filter. In some models of washing machines, you will have to first unscrew and get a plug or bolt.
  • Carry out the filter. First of all, remove large pollution. hair, coins, buttons, threads, etc. Then clean the filter from plaque using the hard side of the sponge. Do not use hot water and aggressive substances so as not to damage plastic and sealing gum.
  • Clean the hole where the filter was installed. Wipe everything with a damp sponge, removing the plaque and the remaining dirt.
  • Clean the drain pump and pump. Shut up in the hole with a flashlight and eliminate all visible pollution.
  • Install the filter in place. Twist it on the thread, without making excessive efforts so as not to damage. Make sure the part is set tight and correct.
  • Connect the unit to the mains and install the pouring hose to the place. Run the washing machine in test mode without linen. Check if there is a leak. If everything works well, set the false panel in place or close the hatch door.

How to clean the filter set yourself-instructions

The pump is located at the bottom of the car, one might say, at the bottom. Sometimes the bottom of the car is not closed by anything, and sometimes manufacturers attach an additional panel there. To get to the pump, you need to remove it. You can also put the car in a position convenient for you to freely interact with the contents of its lower part. When you saw where the pump is located, weaken the clamps of the pipes and free the pump from them. It is necessary to remove everything that holds it in the car: bolts, clamps, fasteners. When it is done, get out the pump and proceed to cleaning.

The design of the pump consists of two parts: the so.called snail and the pump itself with the impeller. In order to clean it, the design will need to be disassembled, but this is not difficult: unscrew a few screws that connect the details. Now you can carefully examine the impeller. Usually, the problem lies in it: all the garbage is wound on it and prevents the pump during operation normally. Take out of it, collect the pump and put in place.

Install the machine in the starting position, connect to all communications and run the wash to then see how the water is drained. If everything is fine, then you managed. If the problem is not eliminated, then the pump must be changed: it has failed. Here are a few simple rules, how to avoid premature breakdown of the pump.

  • Use special washings for washing rooms.
  • Do not wash clothes in unintentional cars, on which there are many decorative elements.
  • Periodically clean.

That’s all! In fact, it is not so difficult to maintain the condition of your home assistant, you just need to do it regularly, otherwise problems will appear worse!

The clogging of filters is evidenced by problems in the work of the washing machine. The following signs are most often manifested:

  • slow fence and drainage;
  • output of error codes to the display;
  • Sharp stop of washing;
  • the inability to include the programs “squeezing” and “rinsing”.

In case of one of the malfunctions, disconnect the unit from the mains and check the condition of the filters.

Cleaning components from wash machine gorenje sensocare 7kg

Problems of the drain or fence of water, errors displayed on the display, and the appearance of an unpleasant odor in the drum indicate a violation of the operation of the filters

The cleaning procedure is quite simple, does not require special knowledge and experience, even a woman who is not familiar with the device of the washing machine can cope with it. The main thing is to adhere to the sequence of the steps described below.

  • Turn off the washing machine from the outlet and redraw the shut.off valve of the water supply to the machine.
  • Unscrew the pouring hose of the washing machine and disconnect it from the body to access the filter. This is usually easy to do with your hands, but if there is not enough strength, use pliers or pliers. There is always a little water in the hose, so hang a rag when unscrewing the hose, if you do not want the remnants of the water to be on the floor.
  • Gently click the filter with pliers or pliers and pull on yourself, it will easily get out.
  • Wash the net under a stream of water. If you want more thorough cleaning, soak it in a solution of citric acid for 30. 60 minutes (at the rate of 1 teaspoon per glass of fuel water). Please note that the water should not be hot. Boiling water can lead to plastic deformation, then you will have to change the fill filter. Warm water is preferable to cold, since citric acid dissolves better in it.
  • Insert the mesh back into the hole of the pouring valve until it stops using pliers or pliers.
  • Screw the pouring hose, completely open the water supply valve to the machine and check that the connection place of the hose to the washing room does not flow.
  • Turn on the washing machine in the outlet, start any program and make sure that the machine fills the water.

We offer to familiarize yourself with how to clean metal pots at home

Dismantling the front of the case

Get to the drain pump in the brands AEG, Bosch, Siemens can only be removed by removing the front panel. This is a little more complicated, act sequentially:

  • Remove the top cover from the body. To do this, unscrew two screws from behind and move the lid in the opposite direction.
  • Now you need to remove the control panel.
  • Pull the submachine tray for the detergent by clicking on the lock in the center.
  • Unscrew two screws behind the dispenser and one on the opposite side.
  • Frowning the latches, disconnect the panel from the body.
  • It is not necessary to disconnect the control of the control module, you can put the panel on the top of the case.
  • Next, you need to remove the base panel.
  • Now open the hatch door. Unscrew two screws holding the uble lock, and also remove the cuffs clamp.
  • It remains to unscrew the screws around the perimeter of the panel and remove it from the case.

The process of seizure of the pump is the same as in the previous case.

Before disconnecting the pipe and pump, substitute the container, because water can result in.

The reason is the bearings

Pollution is not the only reason for the wrong operation of the device. When the bearings are out of order, a beating occurs during the rotation of the shaft. Due to the beat, the impeller begins to rub on the casing of the snail. This causes the noise and unproductive work of the pump, up to a complete stop.

This problem is solved by the replacement of ball bearings that can be purchased at specialized retail outlets or at the household appliance service service center.

If at the moment there is no way to buy a new detail, and washing cannot wait, then you can temporarily extend the pomp of the pomp, shortening the blade 2 millimeters with a sharp knife. But do not overdo it: if you cut more, the performance of the system will fall.

After cleaning, replacing bearings or seals, repair of a motor can be considered complete. Install the case with the blades in the coil and fix it with latches. Subject to safety rules, connect a voltage of 220 V to two contacts, and check the operation of the device. Having made sure of the normal operation of the device, you can connect the snail, and return the entire structure to the body.

As you could verify, the repair of the pumping machine with your own hands is not such an impossible task and for the power of everyone who carefully read these recommendations.

What lubricant to use for the laundry lamp

Now the market has been provided with a large selection of lubricating materials and any table of spare parts for washing machines also provides for its availability. There are specially designed options, but the fact is to carry out the repair of your own packaging on your own, and it will cost a lot.

Packaging usually contain 50-100 grams of material, and with lubrication you will need 1-2 grams.

If there is no original lubricant, the washing machine can be lubricated with others, the main thing is that they meet the requirements of their future operation.

At home, grease the oil seal with the following grease

  • Litol (or Litol-24). It has chemical and mechanical stability in the temperature range from 40 to 120 degrees Celsius.
  • CCITIM 221. It behaves perfectly in the nodes of severe friction, does not change its basic properties at temperatures up to 150 degrees.

Also, many automobile and other solid lubricants, which are today a huge amount, including silicone analogues of washing machines.

The pump of the washing machine

This is the element of the drain system that is responsible for pumping dirty water from the drum. It is located after the filter, therefore, in fact, only water can enter it. But there are situations when the filter passes small objects due to a torn grid, which leads to jamming of the impeller. To solve this problem, you just need to open the filter, see if there are gaps on it. Look inside the pump, are there any extraneous objects. If there is, then you need to remove them and check whether the impeller spins freely.

When examining the impeller, special attention should be paid to the threads, hair, which are wound on the pump shaft, and it is not visible under the impeller. Therefore, you will have to feel the shaft by any means and make sure that it is free. If even in this case the impeller is poorly spinning, it is necessary to disassemble the pump unit itself, because the cause may be the lubricant in the bearings, that is, its absence. The bearings were jammed, the shaft does not spin.

clean, gorenje, washing, machine, vertical

There are frequent situations when everything rotates by hand, and the pump itself does not work. Two reasons.

  • The electric motor burned. Will have to purchase a new unit.
  • Contacts burned in the electric power circuit of the pump, on the sensors of the system of automation or in the power supply. All this will have to be opened and cleaned, using, for example, a solvent or technical alcohol.

Attention! If the pump has burned down, and it is necessary to replace it with a new one, then when buying it in the store, you need to take the old device with you and compare its configuration with the new. That is, you need to accurately choose the required number of cuffs, gaskets, contacts and so on.

By the way, it should be noted that different washing machines have in mind their brand, different methods of how to get about the installation site of the pump.

  • If it is Samsung, Ariston, Kandy, LG or Beko, then you can get through the bottom. That is, the machine must be laid on the side, remove the lower wall. and now the pump is in front of your eyes.
  • If it is Bosch, Siemens or AEG, then this is the most difficult option, because you have to remove the facade panel completely with the control unit.
  • But the washing rooms of Zanussi or Electrolux will have to disassemble from the back. Why it will be necessary to remove the screws of the back wall.

How to get to the pumping machine of the washing machine, so, blockages in the washing machine are rare, but they meet. How to deal with them now is clear. The main thing is not to bring the condition of the device to a critical one, but for this you just need to periodically clean the drain system, especially the filter. Fortunately, doing it with your own hands is not a problem. In addition, it is recommended to use special chemical cleaners, which were mentioned above.

How to understand that the car was clogged

If the washing machine suddenly clogged, then it is quite difficult to identify the blockage only by external signs. Usually, when a strong blockage occurs, draining stops functioning and the washing machine can not plow the spent water from the tank and freezes in the middle of the washing program. At the same time, you visually see through the glass of the hatch that there is water in the tank.

With a weaker blockage, the washing machine cannot drain the water quickly enough. As a result, the washing machine gives out the error code, and also freezes in the middle of the washing, leaving the remaining worked out water in the tank. These are symptoms characteristic of blockage, but this does not mean that these symptoms are not characteristic of other malfunctions. The article Repair of the Washing Machine pump, we consider exactly the same symptoms in the case when the drain pump is out of order.

Some inhabitants think that a broken pump does not make any sounds. Nothing of the kind, a broken pump can buzz as well as good, but still do not fulfill its functions.

The same symptoms can occur in case of malfunction of the control module or the Pressostate of the washing machine. In general, you cannot do without a more detailed study of the issue. What can really be done to determine the malfunction? What is it, blockage or not blockage?

Unfortunately, simple recipes, in this case, no. We will have to alternately check the entire list of possible malfunctions, moving from the simplest and most affordable verification options, to difficult until you come across a breakdown.

How to clean?

The purification process is reduced to cleaning the impeller. A lot of garbage fibers are usually wound on it. wool, hair, threads. The order of disassembly of the pump:

  • Remove the case. snail, unscrewing the screws. In this case, you need to remember the mutual arrangement of the engine and snail.
  • The filter is cleaned using a wooden stick. it is removed with dirt, scale. Wipe the elements of rubber with a slice of lemon.
  • Unscrew the impeller with a screwdriver. unscrew the screws with which two parts of the pump are connected to each other. Then you will get to the impeller. an element rotating during operation. Gently remove the garbage so as not to break the blades. Wipe the snail inside.
  • Collect the purified pump. the assembly must be performed in the reverse order. In order not to make a mistake, record your actions during disassembly. take a photo. Put all the details in place and run the machine. If the assembly is made correctly, there will be no leakage.

How to get a pump

It is done quite simply. Most devices for the pump have a special department in the lower part of the machine. The pump is hidden behind a small rectangular panel, to remove which can be unscrewed by unscrewing the fastening and pushing it with a screwdriver. Next, you need to find a self.tapping screw that holds the part inside the case. Usually he is on the right side of the pump.

The next action will be the preparation of the container in which the water can be drained. This container will need to be substituted under the washing machine, having previously tilted the device. Only after that it is recommended to remove the pump, because water can flow from it.

To seize, you need to drown the part into the machine body and get the pump through the bottom. Previously, you need to disconnect all the wires and hoses. Please note that not all models have the ability to take part. For detailed information, you need to watch the instructions of your device.

Serbian Travel Tip Problems With Doing Laundry

Brill pump

When the pump in your hands can be proceeded with cleaning. First you need to disconnect the impeller, which is attached to several self.tapping screws. It is in this part that many dirt can accumulate, so cleaning begins from here. Then you can clean the snail, getting rid of all the clogs accumulated in it. Subsequently it is necessary to collect everything and install in the same place.

The assembly occurs in the reverse order, after which it will be necessary to check the performance of the machine. If everything is connected correctly, then you can consider cleaning the completed.

Cleaning Gorenje WA60129 Filter

The blockage of the drain pump of the washing machine usually appears due to the fact that a large amount of garbage gathered in the filter. But this is not the only reason for such a problem. Other probable causes of this malfunction can be:

malfunction of the pipe in the area where the pump and tank are connected;

clogging of the sewer pipe and subsequent locking of the passage.

SterilTub Washing Machines Gorenje (UA)

In any case, when the water is drained poorly or does not merge at all, it is necessary to clean the pump in the washing machine.

About the author

| Denial of responsibility | Contacts |RSS