How to connect Garaterm Rondo water heater

How to connect Garaterm Rondo water heater

Garanterm. A water heater, in the reliability of which you can be 100% confident. The company conducts various tests for hardness and safety. Let’s figure out how specifically the devices in production are checked.

  • Acid solution (30%). With the creation of the acid medium of the tank, the resistance of the enamel coating was tested within the 1st month. Rust and metal corrosion were not detected.
  • Hydemes with high power. Garaterm water heater (abstract contains this information) was tested for the hardness of the storage tank within 86 hours. For a second, two rather strong water jackets were served. There were 150 thousand cycles in total. This indicates that the warranty period of the tank material is about 20 years.
  • Checking the highest pressure. Within 3 minutes, the tank of the tank increased the pressure to 24 atmospheres. The test results showed that the walls and the coating were not deformed, the leaks were not detected.
  • Temperature changes. In order to check the hardness of the accumulative tank, in the laboratory criteria, at first, snitches sharply raised the temperature to 93 °, and then lowered to.20 °. There was no deformation.

How to launch a cumulative boiler

The first launch of the electric water heater must be made by the equipment for the installation of equipment immediately after the installation of the device. The quality installation, the launch of it is evidenced by its signature, printing of the company in a technical passport, warranty coupon. Without this procedure, it is impossible to guarantee the boiler in the future.

Under conditions when it is impossible to invite the master to install, the launch of the system, you have to connect the boiler yourself. The sequence of actions at the first launch:

  • Checking the quality of the water heater installation, determination of leaks, if they are:
  • Disconnect the water heater from power;
  • Fill the water heating tank with water opened with hot water supply. After water starts to flow from the hot tap, you need to stop the water set, since the tank is already filled;
  • Close the crane, it is advisable to leave the boiler for a while;
  • Inspect the water heating structure. Determine the integrity of the compound elements. If there are no leaks, you can connect the device to the power supply. The presence of leaks must be eliminated.
  • Connect the boiler to the mains, put the heating mode.
  • Make sure, having checked with the technical documentation that the amount of time spent in heating corresponds to the norm, and the water of the desired temperature.

After a long shutdown of the boiler (winter period in the country, use in the apartment when disconnecting hot water supply) is launched according to the given scheme.

Technology

Garanterm. A water heater, when creating which innovative technologies are used. Let’s look at them:

  • Point Y. A system due to which the reliability of the connecting place of three seams increases significantly. The essence of the technology is to use cold welding. Due to the fact that the chrome surface does not heat up, the strength of the connection increases by 30%.
  • Flat tank. The use of two storage tanks. Used in flat models with dry.Type heating heater.
  • Superfoam. The efficiency of thermal insulation. As a rule, all models use polyurethane, which has a low level of thermal conductivity. Thanks to its use, it was possible to significantly reduce heat loss.
  • Cold Metal Transfer. A technology for using cold welding, which preserves the quality of stainless steel as much as possible.
  • Dry Coat. A system for protecting the surface of the internal walls of the tank. Enamel is applied with an uniform layer and firmly fixed.

Do.It.Yourself installation instructions

Installation of the guarantor heater according to the instructions. The process is not very complicated, takes about 3 hours and consists of 4 stages:

  • With the help of available mounts, the boiler is mounted on the wall. It is necessary to place it in such a way that the distance from the protective cover to the ceiling is at least 0.3 m.
  • Connection to the water supply. A safety valve is installed on the cold water supply tube. It is recommended to clamp it for 4½ turns. The exit from the heater is painted red and screwed to the tap with hot water. The joints should additionally be compacted using pacli or fum tape.
  • To discharge air in the boiler system, both taps must be opened simultaneously. When the installation capacity is completely filled, the water will flow from the tap with hot water.
  • Using the connector, the water heater connects to the mains.

If your boiler is often disconnected, in the process of work to publish extraneous noises (hissing, gurgling) and the time of heating the water has increased, then the time has come for a small prevention: cleaning the hectes from scale. Do.It.Yourself repairs of the guarantor boiler are carried out in accordance with the following instructions:

To get to the heating elements, you need to unscrew 2 self.Tapping screws from behind and 2 on the sides of the installation case.

A review of the flat water heater Garanterm indicates that in the devices of this manufacturer, as a rule, 2 heating elements with a capacity of 0.7 and 1.3 kW are installed. Therefore, both will have to take off. For these purposes, you need a wrench for 10 and a cross screwdriver. First of all, the fastons of thermal protection are removed, then the screws are unscrewed from the heating contacts and the bar is extended to the flange. After these manipulations, you can remove the nut that fixes thermal protection and carefully remove the thermal landers. 6 Ten fasteners are unscrewed with a wrench, a fixing bar is removed and after the heater itself is removed.

Scale is eliminated using a knife and warm water. It can be removed from the tank, filling water with citric acid there. Having stood so 2-3 minutes, shake the container and drain the water. The procedure can be repeated several more times, but already without acid.

Assembly is carried out in the reverse order.

“In the bathroom, a stainless boiler of the Narrow series with a tank volume of 50 liters was installed. We have been using the third year, except for leaks in the places of connecting hoses of problems, there were no problems. We cope with this trifle with the help of a sealing tape. Otherwise there are no complaints. Electronic control works fine. The function of accelerated heating is very pleasing. The second heating element turns on and the water is heated twice as fast. Which also pleased was an elegant thin case and compact size “.

“The water heater has acquired a stainless steel guarantee of IMAGE 100V series. For a family of 3 people. A great option. The most pleased with the presence of an economical mode, when the water temperature is supported in the range of 40–45 ºС, while the consumption of electricity is the minimum. Over the past from the moment of purchase of 8 months there was no water leaks. It works quietly, it takes little space, looks great on the wall in the kitchen. “.

“3 reinforced boiler of the Origin Mini series with a capacity of 10 liters were installed in their house. One in the kitchen, the second and third in bathrooms on 1 and 2 floors. Placed them under washbasins, in the cabinets. They work perfectly. Warm up to 80 ºС in 5-10 minutes. Therefore, it makes no sense to keep them constantly included, which saves electricity. At first, with an increase in pressure, joints of the compounds led. I had to reproach them, additionally compact Latex and the problem disappeared. “.

See also  Towel rail leaks after hot water shutoff

“We installed a water heater in this brand by 80 liters, after 2 years the heaps were burned out, after 3.5 years the tank flowed. Despite the fact that the tank has a warranty of 7 years and the service center provided an act with a conclusion about factory marriage, they refused to replace the hotels. Do not believe the guarantees. This is all the lure of the manufacturer to overstate prices, there is no such quality of your money “.

“We bought a 100 liter guarantee water heater, since we had a small child. Exactly a year later he began to leak and after a couple of months he simply broke through. It is not subject to repair, since the inside rustled. Heated water was enough for two days and it was not constantly turned on, only to heat water, only for a couple of hours. I am very upset, now I need to buy a new one, but in general I was pleased with it “.

“The water heater has worked for 50 liters exactly 7 years without Комментарии и мнения владельцев and misunderstandings. Now the water began to drip water for fastening with the lower lid, and then from under the glass on the thermostat. Disconnected, removed the lower lid and it works, warms up “.

Garaterm series GTN 80 V is good, no Комментарии и мнения владельцев. Enough for 4 years, flowed along the weld in the second capacity at the top. And where I do not go, no one corrects such a breakdown “.

How to disassemble a water heater with a heater

Scheme of an electrical flow heater.

This is a relatively inexpensive type of boiler, which has a heater attached to the nuts. This device, as a rule, has no external adjustment. Its distinctive feature is the presence of a hexagonal flange, which is spinned by a 55 or ordinary gas key with a key.

A water heater analysis algorithm with Ten:

The device is disconnected from the network, drained water and dismantled the check valve, which will only complicate the operation; The boiler cover is removed, which is fastened with screws closer to the nozzles; The thermostat is dismantled; A container is substituted under the water heater, into which the remains of dirt, water and scale will merge; They spin the flange counterclockwise (the existing dirt and scale can complicate the work, so they are carefully cleaned with a wooden or plastic knife; as soon as the thread ends, the flange is carefully extracted); In order to extract the heater, the scale is removed in the bends of the heating element and, carefully swinging left and right, pull out the lower part of the element.

How to disassemble the water heater (boiler) of the economy class, the economy class water heaters are distinguished by an oval form of the flange, therefore, the principle of their analysis has some features.

  • The device is disconnected from power, drain water and, if necessary, unscrew the check valve;
  • There are two screws near the rods and the bay, which should be unscrewed and the water heater lid should be removed;
  • The thermostat is removed with a sharp movement down and access to the flange is opened, which is attached by a nut to the body by means of the bar; After the nut is promoted, you can remove the flange.

How to disassemble a medium-class water heater water heaters of the medium class have an average price category. The device includes flanges that are attached directly to the neck using 6 bolts.

The process of parsing this water heater is as follows:

  • The power of the device is turned off, water is drained and the check valve is dismantled;
  • To remove the lid, they find the screws and unwind them (the location of the screws may be different);
  • After this, it is necessary to extract or remove the thermostat (depending on whether it is connected to the heating wire or inserted into it);
  • All the necessary screws or nuts are promoted.

GARANTERM MGR 10.U

Mod MGR 10-U-a small device of the Garanterm trademark type of brand. The water heater is designed for 10 liters of water. Heating element. Tubular Heater, with a capacity of 1,500 watts. Dimensions of the device: 33 × 36.4 × 37.3 cm. Installed on any type of walls. Does not require additional strengthening, as it weighs only 7.7 kg. Connection of the water system from below. Most often installed under the sink. Water heats up to 45 ° in 42 minutes to a temperature. Currently, the Garaterm MGR 10.U water heater can be purchased on average for 5000.

Ремонт електричного бойлера Garanterm

Signing Mini lineup

Significant differences in the collection are such as:

  • Super.Compact dimensions of the equipment;
  • Minimum volume. 10 l, maximum. 30 liters.
  • Type of placement. Above or under the sink.
  • Due to the minimum size, heating time is reduced. From 25 minutes to 1 hour 10 minutes.

In the manufacture, the same techniques and materials were used as when creating the above selection of Origin Slim.

Smart collection

The models presented in this section are ideal for small rooms. Features and advantages of products are as follows:

  • Narrow diameter of water heaters. 27 centimeters;
  • Maximum power indicator. 2000 watts;
  • One tank of “stainless steel” and two heating elements;
  • Point Y system;
  • Cold welding Cold Metal Transfer;
  • Reliable isolation from low.The.Floor polyurethane foam Superfoam;
  • Temperature controller is placed outside;
  • Three power modes;
  • Warranty period. 7 years.

Vertical models of the boiler are represented by such technical characteristics as:

  • GTC 30 v. Pressure. 0.6 gram/volume. 30 liters/power. Double power mode: 0.7 kW 1.3 kW = 2.0 kW/height. 76 centimeters/width –27 centimeters/depth. 28.7 centimeters/weight/weight/weight. 8.8 kg/heating time. 50 minutes;
  • GTC 40 v. 0.6 GMO/40 l/0.7 kW 1.3 kW = 2.0 kW/98 cm/27 cm/28.7 cm/10.9 kg/1 hour 5 minutes.

Origin Slim series

Features and advantages of products are as follows:

  • Original elongated (narrow) form;
  • White color;
  • Strong and wear.Resistant enamel;
  • Reinforcement according to the Mineral Glass methodology;
  • Application of enamel through Dry Coat technology;
  • Superfoam thermal insulation;
  • Enlarged magnesium anode;
  • Power. 1.5 kW;
  • Warranty. 5 years.

Vertical models from the series are represented by such parameters as:

  • ES 30 V (TR). Pressure. 0.6 GU/volume. 30 liters/height. 50.3 centimeters/width. 36.5 centimeters/depth. 37.5 centimeters/weight. 13.5 kg/heating. 1 hour 5 minutes;
  • ES 40 V (TR). 0.6 GU/40 L/62.8 cm/36.5 cm/37.5 cm/15.7 kg/1 hour 25 minutes;
  • ES 50 V (TR). 0.6 GU/50 L/75.3 cm/36.5 cm/37.5 cm/17.4 kg/1 hour 45 minutes;
  • ES 60 V (TR). 0.6 GU/60 L/87.8 cm/36.5 cm/37.5 cm/19.5 kg/2 hours 10 minutes;
  • ES 70 V (TR). 0.6 GU/70 l/100.3 cm/36.5 cm/37.5 cm/22 kg/2 hours 30 minutes.

The horizontal version is represented by only one model, namely ES 50 H (TR). 0.6 GUM/50 liters/36.5 centimeters/75.3 centimeters/37.5 centimeters/17.4 kg/1 hour 45 minutes.

The Origin lineup

Boilers presented in the collection will at a high level will appreciate the classics connoisseurs. Smooth forms in snow.White enamel will give the interior of lightness, light and radiance. Features are as follows:

  • The enamel used to cover water heaters retains whiteness throughout the entire life and does not crack;
  • The manufacturer used a special methodology for reinforcing the enamel of the internal tank of the Mineral Glass;
  • The enameled coating is applied through the dry Dry Coat methodology;
  • The maximum efficiency of the heating element is 1500 kW;
  • Luminous power indicator;
  • To increase the protection of the internal tank from rust, the manufacturer increased the magnesium anode;
  • Reduction in electricity consumption due to Superfoam thermal insulation;
  • External temperature control;

The technical data of the vertical type devices are such as:

  • ER 50 v. Pressure. 0.6 GU/volume. 50 liters/height. 55.8 centimeters/width. 44.5 centimeters/depth. 45.5 centimeters/weight. 17.3 kg/heating time. 1 hour 45 minutes;
  • ER 80 v. 0.6 GU/80 l/79.8 cm/44.5 cm/45.5 cm/22.4 kg/2 hours 50 minutes;
  • ER 100 v. 0.6 GU/80 l/79.8 cm/44.5 cm/45.5 cm/22.4 kg/2 hours 50 minutes.
See also  No water in the dishwasher

Horizontal models have the following technical indicators:

  • ER 80 h. Pressure. 0.6 GU/volume. 80 liters/height. 79.8 centimeters/width. 44.5 centimeters/depth. 45.5 centimeters/weight. 22.4 kg/heating time. 2 hours 50 minutes;
  • ER 100 h. 0.6 GU/100 L/95.8 cm/44.5 cm/45.5 cm/25.7 kg/3 hours 30 minutes.

The following belong to the floor models:

  • ER 200 v. Pressure. 0.6 GU/volume. 200 liters/power. 5 kW/height. 121.6 centimeters/width. 56 centimeters/depth. 67.2 centimeters/weight. 61.2 kg/heating time. 2 hours 15 minutes ;
  • ER 300 v. 0.6 GU/300 l/5 kW/170.5 centimeters/56 centimeters/67.2 centimeters/80.1 kg/3 hours 25 minutes.

Popular models

It is very important to choose a suitable water heater in size and power. To buy optimal equipment, you must be guided by several selection criteria:

  • The size. In city apartments there is no way to take a whole room to a full boiler room, so the equipment is located in the bathroom or in the kitchen. So that it does not take up a lot of space, the owners choose small water heaters.
  • The form. Sometimes, to save space, it is advisable to buy an unusual boiler (narrow cylindrical or flat). It will depend on the features of the place for the boiler.
  • Power. In houses with weak wiring, it is important to install a low power device. This will reduce the risk of short circuit.
  • Appearance. This parameter is especially important for devices installed in the apartment. The water heater has to be in a prominent place, so the choice of attractive outwards is very important.

The water heater is purchased for many years, so you need to approach the choice very responsibly: study the ruler, read the review and reviews for each model, calculate the volume of the tanks and check the possibility of installing a boiler.

For the apartment

A boiler in a city apartment is able to save the owners from discomfort during the period of disconnecting hot water supply. The water heater works only a few weeks a year and is located in a prominent place, so the hosts prefer small structures. The most popular models for the apartment:

  • GARANTERM GTN 80 V. The small depth of the device allows you to install it in the kitchen above the sink or in the bathroom. Thanks to a small size, the device does not create discomfort when working in the kitchen. Two tanks make it possible to simultaneously heat and consume water, an impressive volume of the boiler is able to provide a large family with water.
  • GARANTERM GTR 50 V. Narrow and high wall boiler. Easily placed in a small space. The power of the device is 2.0 kW.
  • GARANTERM ER 50 V. A successful model for installation in the apartment as a spare source of hot water. A small wall water heater in a cylindrical shape is easily placed in the bathroom and provides water with an average family of 3-4 people.

When choosing equipment for the apartment, you need to pay attention to the power consumption of the heater and select a safe boiler for wiring.

For a country house

In country houses where people constantly live, the water heater becomes the only source of hot water. When choosing a boiler, its reliability and tank volume are put in the first place. Popular models for private houses:

Водонагреватели накопительные GaranTerm | нержавеющие | эмалированные | плоские | круглые | ТЭН

  • Garaterm Er 50 V is a good option not only for an apartment, but also for a private house. It is ideally installed in a special boiler room or in the bathroom. An economical model with a capacity of 1.5 kW heats the entire volume of water in 75 minutes.
  • GARANTERM GTR 80 V. A narrow boiler is easily installed in the bathroom, invisible in the interior, placed in almost any niche. The fast heating function allows you to raise the water temperature to 75 degrees in just 130 minutes.

When installing a water heater in a private house, it is recommended to allocate a separate room for him. This will allow you to regulate the heating parameters, monitor the level of water and control the correctness of work even when it is busy in the bathroom.

Popular models

It is very important to choose a suitable water heater in size and power. To buy optimal equipment, you must be guided by several selection criteria:

  • The size. In city apartments there is no way to take a whole room to a full boiler room, so the equipment is located in the bathroom or in the kitchen. So that it does not take up a lot of space, the owners choose small water heaters.
  • The form. Sometimes, to save space, it is advisable to buy an unusual boiler (narrow cylindrical or flat). It will depend on the features of the place for the boiler.
  • Power. In houses with weak wiring, it is important to install a low power device. This will reduce the risk of short circuit.
  • Appearance. This parameter is especially important for devices installed in the apartment. The water heater has to be in a prominent place, so the choice of attractive outwards is very important.

The water heater is purchased for many years, so you need to approach the choice very responsibly: study the ruler, read the review and reviews for each model, calculate the volume of the tanks and check the possibility of installing a boiler.

For the apartment

A boiler in a city apartment is able to save the owners from discomfort during the period of disconnecting hot water supply. The water heater works only a few weeks a year and is located in a prominent place, so the hosts prefer small structures. The most popular models for the apartment:

  • GARANTERM GTN 80 V. The small depth of the device allows you to install it in the kitchen above the sink or in the bathroom. Thanks to a small size, the device does not create discomfort when working in the kitchen. Two tanks make it possible to simultaneously heat and consume water, an impressive volume of the boiler is able to provide a large family with water.
  • GARANTERM GTR 50 V. Narrow and high wall boiler. Easily placed in a small space. The power of the device is 2.0 kW.
  • GARANTERM ER 50 V. A successful model for installation in the apartment as a spare source of hot water. A small wall water heater in a cylindrical shape is easily placed in the bathroom and provides water with an average family of 3-4 people.

When choosing equipment for the apartment, you need to pay attention to the power consumption of the heater and select a safe boiler for wiring.

For a country house

In country houses where people constantly live, the water heater becomes the only source of hot water. When choosing a boiler, its reliability and tank volume are put in the first place. Popular models for private houses:

  • Garaterm Er 50 V is a good option not only for an apartment, but also for a private house. It is ideally installed in a special boiler room or in the bathroom. An economical model with a capacity of 1.5 kW heats the entire volume of water in 75 minutes.
  • GARANTERM GTR 80 V. A narrow boiler is easily installed in the bathroom, invisible in the interior, placed in almost any niche. The fast heating function allows you to raise the water temperature to 75 degrees in just 130 minutes.

When installing a water heater in a private house, it is recommended to allocate a separate room for him. This will allow you to regulate the heating parameters, monitor the level of water and control the correctness of work even when it is busy in the bathroom.

Customer reviews

In the reviews to guarantee water heaters, users note their efficiency, durability and ease of operation. Some Комментарии и мнения владельцев indicate a high probability of leaks due to the divergence of seams on tanks.

We have a boiler Garaterm GTN 50 V. In any position of the thermostat, warms up to boiling water. Both thermostats changed. What could be the problem?

See also  What is it what is heating convectors

It is remote to determine the problem, perhaps the reason in the temperature sensor, but other malfunctions are not excluded, you can precisely determine the breakdown only on the spot. It is recommended to call the master.

After a year of downtime, when the storage water heater was first turned on, the guarantor of 80 liters overheat the water, poured boiling water with steam (the regulator was put to average). After that, when connecting to the outlet, the light bulb began to shine dimly on the key 1.3 kW. The keys when turning on shine brightly. Electronics drew? Device in operation 2 years.

Based on your description, we can conclude that the thermostat did not work (did not turn off at a given temperature), as well as a protective thermostat (urgently did not turn off the device when the temperature exceeds more than 90 degrees). All this is very similar to the fact that the heater, in which the sensors of the thermostat and thermal protection are covered with a scale. Therefore, thermostats did not work. In your case, you first need to clean the heating heating element. If there is no scale on Ten, I would advise you to immediately buy a thermostat, thermal protection, button and put it all.

The Garaterm GTN 80 V electric water heater does not warm the water, the buttons of turning on the heater do not light up. I read that thermal protection worked. I opened the lid, found a button, but it doesn’t work to press it (the button sticks about 3-4 mm). Tell me how much it performs when thermal protection is triggered? And what effort to make to press this button? I use the device constantly only 2 weeks.

The fact that the thermal protection button is 3-4 mm, this means that it worked. I just have to press it, and it will drown with a click and fix it. It must be drowned, t.E. Be on the plastic. If this does not happen, and the thermal protection flask (it is in the heater and it must be removed from there) is cold, then you need to change the block.

Dripping from the check valve of the boiler guarantor for 50 liters. What can be done?

If it drips from a return valve, then this should be. The check valve is designed to set out excess pressure. There are two exits: put a gearbox on cold water, or put a rubber (silicone) hose on a check valve on a check valve, and bring its second end to the sewer.

Tell me, please, according to the Garaterm GTN 30 V model. After replacing the heating elements, he often began to turn on, every 3-5 minutes. The thermostat is faulty?

To say exactly, you need to look at the boiler, the reason may be in the thermostat, may not quite fit the new heating elements, other malfunctions can also be detected during examination. It is recommended to call the master.

When installing a storage water heater, the guarantee (100 liters) during the tightening spent the hot water pipe for half a turn. Leaks did not form. This will not lead to an increased risk of leakage?

To make sure that there will be no leaks, you need to remove the tank and see what happened. Otherwise there is a risk of leak.To. The tank is under pressure.

I have such a question, today I changed the heating elements to the EVN GARANTERM ER 50 V. After heated water to about 45 degrees, but after draining 20 liters, barely warm water went. Before before, they bathed in the cabin for an hour, and the water was hot. Another question is that the old hets worked for 4 years, there are no scraps on them, but they are dark red color (the heater burned at 1.3 kW), there was no anode on it. It disappeared.

And you used the device in what heating mode? If all 2 heating houses were involved (2 burning buttons on the switch signal this), then try to set the temperature of the water thermoregulator. It is strange that with 45 degrees set, you used to bathe in the cabin for an hour, and the water was hot. Most likely, it was exhibited much more, or before repairing the pressure of hot water was small (somewhere there was a blockage), and now, after washing, the pressure has become larger, respectively, and water consumption has increased.

Please help me with such a problem, installed a 30 liter guarantee, he warmed at first normally, but then he began to beat the current. And warm only a couple of divisions, the water flows only warm, while the regulator is put to the maximum. What it could be, heating or regulator?

Most likely, Ten. First you need to check the heater for a leak on the case. At the same time, in the same way, you can call the thermostat. One probe for the long tube of the thermostat, and the second probe for any of the two contacts of the ones going to the heater, and then on the second. If there is a leak, you need to change the failed element.

We have an electric water heater guarantee of 80 liters. They put an RCD. Used it, everything was fine. Yesterday the RCD itself turned off. They removed the device, took out the hets (one was recently changed). Tenes in normal condition. We hang back. Turn on the outlet (buttons on the unit are turned off). The RCD immediately turns off. In the same outlet we turn on the kettle, everything is fine. We think the reason in the water heater, but what? Advise what the reason can be?

RCD, usually disconnected in 3 cases: Ten breaks on the case. Some part of the circuit pierces on the case (this happens very rarely). Malfunctioning the RCD itself (rare case). How to find out that it doesn’t work. To find out if the RCD itself is buggy, you need to turn off 2 fastons from thermal protection. After you are turned off, you can stick the fork into the outlet. If the RCD worked at this time, then it is necessary to change it (it will fail). If the RCD did not work, then we need to remove the fork from the outlet, put fastons on thermal protection, remove the fastons from the heels (that is, de.Energize them), and again include the fork in the outlet. If the RCD did not work again, then we take out the plug out of the outlet, and begin to put on the fastons first on one heating element (and turn on the fork in the outlet), and then on the other heater. Or “call” the heater to the case.

I have a Garaterm ER 80 V heater, in operation for two years. History is this. The defense for the inclusion of the heater at 1.3 began to work. Opened the contact group, saw condensate from below, well, this happens when cold water is very cold. Wiped, dried with a hairdryer, squeezed contacts. Everything worked, heated with two hets to a normal shutdown, but after a few hours the defense began to work again, but already at the heater 0.7. I can’t understand anything, the call of the system does not give anything. I turn on Ten 1.3. Everything is fine, as soon as I connect 0.7, everything goes out. Before drying, everything was the other way around. Tell me, maybe there was something like that?

About the author

| Denial of responsibility | Contacts |RSS