How to disassemble the door of the oven Ariston

Repair of a gas stove door at home

According to users, incomplete door covering is a common breakdown in the wind furnaces of gas plates. Frequent malfunctions in the operation of the unit are possible due to clogging of the spray, which supplies gas, breakdown of the candle of ignition, damaged wire, sticking the power button or unit associated with electrical ignition.

The oven door does not fit due to violations of the operating conditions. Often children sit on the open door, and the brackets, without withstanding such a tension, bend and do not press the door leaf enough tightly. In this case, the repair of the furnace at home will not be difficult. If the reasons lie in the malfunctions of the electrical circuit apparatus, the operation of the thermocouple, then you should seek help from an electrician or another special master.

Also, other factors can be the slowness of the mount and the malfunction of the sealing laying. In the first case, the mount must be tightened, and the gasket should be replaced with a new. It is possible to clean the gutter and install the seal after you remove the door from the loops. About how to do it,

Necessary tools

Before you put the door of the oven, whether it is an electric or gas model, you need to prepare the following tools:

The latter will need when you need to install a new glass. When cleaning, put rubber gloves. While working with glass. Dense mittens. The design of many models of modern ovens allows you to remove the door without tools, but they are necessary to repair other parts.

How a breakdown is manifested?

Ariston oven may not heat up for various reasons. This breakdown is also manifested in different ways, for example:

The oven does not heat up to the required temperature in the same regulator position.

This indicates a malfunction of the temperature sensor regulating heating. Most likely, the part will have to be changed.

The temperature in the oven does not increase more than 100-150 degrees.

As a result, the dishes are prepared for a long time, they are not baked. There may be several reasons for this failure. These are holes for the cable, burning out of the heater, malfunctioning of the thermostat and a worn door seal.

There is no heating in the lower part of the oven, while the dish is burned on top.

This indicates that the lower heating element is faulty. If 4 heating elements are installed in the Ariston oven model, then the reason is in the fan.

After turning on, the oven remained cold.

This is not due to damage to the wiring. Contacts could leave or there is a short circuit in power circuits.

The indicator does not shine when the switch is rotated, the oven does not heat up.

This indicates problems in internal wiring. There may also be no electricity on the network. You need to check the voltage supply, power cord, socket.

Now let’s deal with each cause of the breakdown in more detail.

When you need a master?

The assistance of the engineer of the service center will be needed if the oven Ariston has broken. Before calling a specialist, check the power cable, outlet and electricity on the network. Everything is good? Call by phone 7 (495) 137-76-30. The engineer will arrive within 1 hour.

How to remove the loops?

The loops are removed in the same way as when removing the door. But you will have to unscrew several additional mounts. During execution, the structure will be divided into several parts. There are loops in one of them.

The oven can open poorly or close for the following reasons:

For ovens of the Bosch brand, the spring is placed on both sides.

In order not to break the loops when cleaning the doors, the following rules must be followed:

• You need to unscrew and remove the loops slowly, because if you do not calculate the strength, the details may break.
• Before removing the loops, make sure all the screws were twisted. If there is only one, the fastenings can bend, and then you will have to change them.
• Do not use force when separating doors or glass. Companies make ovens so that all its details can be removed without problems. If you feel resistance, most likely you are doing something wrong.

How can you clean the door and glass of the structure?

Not all detergents are suitable for glass in the oven. Powders can cause cracks. Therefore, it is better to make a solution. Using soda, you can cook it with your own hands:

• Take the sprayer and pour two glasses of warm water into it, add a little liquid soap. Mix the composition with a half teaspoon of soda. Spray the liquid on the glass. After 30-40 minutes, wash the glass in warm water.
• Take soda. Add a little water so that the mixture is thick. Apply to a dirty place. This method has a drawback. You will have to wait a few hours, and only then wash off the mixture from the glass.
• Take a baking powder, which includes soda and citric acid. Spread the mixture in contaminated areas. Wait for 1-2 hours. This cleaning method is very effective against fat. He begins to gather in small lumps, which is easy to remove with a soap cloth or washcloth.
• Funds containing alcohol are also suitable for cleaning.
• Efficiency is effectively struggling with fat. Mix two tablespoons per liter of water.

How can you clean the door and glass of the structure?

Not all detergents are suitable for glass in the oven. Powders can cause cracks. Therefore, it is better to make a solution. Using soda, you can cook it with your own hands:

• Take the sprayer and pour two glasses of warm water into it, add a little liquid soap. Mix the composition with a half teaspoon of soda. Spray the liquid on the glass. After 30-40 minutes, wash the glass in warm water.
• Take soda. Add a little water so that the mixture is thick. Apply to a dirty place. This method has a drawback. You will have to wait a few hours, and only then wash off the mixture from the glass.
• Take a baking powder, which includes soda and citric acid. Spread the mixture in contaminated areas. Wait for 1-2 hours. This cleaning method is very effective against fat. He begins to gather in small lumps, which is easy to remove with a soap cloth or washcloth.
• Funds containing alcohol are also suitable for cleaning.
• Efficiency is effectively struggling with fat. Mix two tablespoons per liter of water.

Removing inner glass

To do this, you first need to understand how it is attached. The glass with the upper end enters the special groove of the bar, and is held below a pair of stops. Usually there are usually two rubber inserts embedded in the frame of the doors, on which the canvas is laid. The use of adhesive compounds by the manufacturer is most often not provided. The bar with the groove is attached to the door with secret screws, which are not visible due to glass. But the stops are fixed with the help of metizes that can be safely unscrewed. As a result, the glass will be released from below. It remains only to push the glass, slightly pressing it with your fingers. If the matter is tight, then you can use a flat screwdriver by slipping it into the resulting gap and tidying the canvas.

Before connecting the stove using a flexible hose, check in your gas

Service, is this type of connection is allowed by local standards and the necessary

When connecting, the following requirements must be observed:. The selected hose must have a document indicating the date of manufacture, term

Service and replacement, and installed in accordance with the rice.Nine;

The plate is connected to the 220-230 V network (50 Hz). The outlet should be in

Easily accessible place and should not be closed with a stove.

After installing the plate in place, be sure to check

The position of a flexible hose of gas supply and power cord (rice.Ten).

They should not go over the chimney and touch the back wall

Plates. During the operation of the oven there is a high temperature,

Tearing portal about repairing washing machines with your own hands, repair of dishwashers, repair of boilers and refrigerators

There are instructions for electric and gas plates, hobs and ovens of Ariston and HotPoint-Ariston. To download the leadership, you need to find a model of your device and click on the name, the file will open in a new tab.

The products of the company are known and loved all over the world thanks to several important parameters that highlight the brand among other manufacturers.

Firstly, HotPoint is distinguished by the ability to create smart equipment with a stylish design. The company has a long and rich history, vast experience, which allows you to use the latest technologies and development in production. Therefore, the products of this company always look unsurpassed in the kitchen and make our life easier, thanks to their outstanding characteristics.

Secondly, the devices of this manufacturer are smart, which means that they used innovations aimed at reducing electricity consumption. Technologies that are used in brand devices allow you to carefully spend natural resources.

Various devices can be used for cooking, but due to frequent use and intensive work, they are especially susceptible to breakdowns. Repair of electric stoves can be carried out with your own hands at home without taking a bulky equipment to a service center.

Despite external complexity, this device has a very simple design. All working elements are installed in a special heat.Resistant cabinet made of alloy steel.

The principle of operation of the electric stove is based on heating the heater by leaking electric current on it. The device is equipped with heating elements that are necessary for cooking. They are ceramic, tubular, halogen, continuous.

• Ceramic burners are presented in the form of a tube, so they can be used for any electric stoves and their repair is very easy to carry out yourself. The spiral is laid in the hole in the plate and fixed using special parts. Now glass ceramics are increasingly used, which is more affordable and durable, in addition, it is washed;
• Halogen burners are considered economical, they work due to halogen lamps with reflectors. These lighting devices are installed in various areas of the hob and provide rapid heating and low electric energy consumption;
• In old domestic tiles (dream, ZVI and others), cast.Iron spiral hets were often installed. They slowly heated, but after disconnecting they gave the heat for a very long time. Separately, it is necessary to note their durability and resistance to moisture and the effects of high temperatures;
• Tubular spiral made of a hollow pipe. When heated, it not only gives heat, but also promotes the circulation of warm air inside itself, which allows you to increase the efficiency of the device. This type of fireplace is most difficult to repair yourself.

To power the slab, a power wire is used, which is connected to all burners. In addition, they are also connected to regulators and thermostats that act as a system of safety system. After turning on, the wire begins to transfer energy to the heater, which is necessary for cooking. Control the level of heating and the burner must be using the corresponding handle. Many household plates of Ardo (Ardo), Indesit (Indesite), Electrolux (Electrolux), Zanussi (Zanussi) and others besides these devices also built.In timers and signaling devices. They help to control cooking time.

Photo. Modern slab with halogen lamps and sensor

Unlike gas, electric stoves are considered quite safe in everyday use. Their repair and maintenance can be easily performed independently, and in terms of durability they are much better than gas models. In particular, this is because they can be cleaned at home, and not wait for the arrival of a specialist.

• When working, the smell of burning appears. If the smell of burning food is worried, then the repair is not needed, it is required to clean the cooking surface. If it stinks of plastic or rubber, then you need to urgently call an electrician;
• The burner does not warm. The reason may be the absence of voltage, the problem of the spiral or the control handle. It will be required to repair the burner or its wire;
• The heating temperature is not tuned. It will definitely require repair of the mode switch;
• The burner does not heat up. The frequent problem of desktop and stationary plates is that they crackle. They can be destroyed as a result of a blow or from a sharp temperature difference (for example, the spiral was heated, and cold water accidentally fell on it). This is the reason for the lack of heating of the burner or uneven heating of food. Independent repair of the spiral is very easy to carry out without the help of the master. The thicket of everything just needs to be replaced;
• Bad work of the oven. Most likely, the problem also lies in the breakdown of the spiral.

It should be noted right away that the corporate service will not undertake to carry out warranty repairs after extraneous intervention. Therefore, if you do not have such an experience, then it is better to immediately contact specialized workshops.

Repair of ovens Ariston with your own hands

Details: Repair of ovens Ariston with your own hands from a real master for Olenord.Com.

Modern ovens break quite rarely, but problems in their work are not excluded. The difficulty is that the design and all its elements do not provide for extraneous intervention. Repair of ovens at home is usually carried out by replacing components and conducts it in most cases an experienced master. However, in some cases, breakdowns can be eliminated independently.

If you decide to try to repair the oven with your own hands, then you should know situations when this should not be done. Definitely do not need to open the body if:

• The electric oven is under warranty;
• The oven’s information panel shows that the problem is to break down the complex component;
• You don’t know anything in electrical engineering.

During the warranty period, all repairs are made for free. With the exception of the following cases:

• There are traces of opening attempts on the design. Erased or damaged heads of bolts, screws, removed seals.
• Insects or rodents penetrated the oven, which caused a short circuit or mechanical damage to the nodes and wires.
• The connection was made incorrectly, without compliance with the recommendations of the manufacturer.
• Damage to the electronic components occurred due to changes in voltage parameters, as a result of which it went beyond the critical limits indicated by the manufacturer.

In all cases when the warranty is removed, the repair will have to be paid in full. The same situation is observed with the expiration of the warranty service.

Before grabbing the multimeter, put on gloves and get a set of screwdrivers, it makes sense to check the presence of energy in the oven. It is worth looking for answers to the following questions:

• Whether food is supplied?
• Is the power cable okay?
• Is it good contact between a socket and a fork?
• Are there any traces of soot, melting on a fork and outlet?
• Whether a fork or oven was out of order?
• Is the power wire ideal, are there any fractures, scuffs or melting?

If there are no problems described above, but the oven still does not start, it is worth checking the device for standard malfunctions.

Consider typical malfunctions, methods of their diagnosis and the necessary repair of electric wind cabinets at home. As mentioned above, most work to eliminate problems is to replace the nodes and details.

If the block of electronic control of the oven suddenly fails, then be prepared to give a tidy amount for repairs. In most cases, nothing needs to be done to identify this problem. Modern models of ovens are equipped with a self.Testing system: electronics will independently give a signal by output of an error code display.

DIY control module repair is possible only if there is experience and knowledge in electronic technology.

Details are replaced, they can be ordered according to the manufacturer catalog. It is better to call users who prefer to get a baked chicken from the oven, not electronic boards, it is better to call a qualified master.

If this is not possible or the qualifications of service personnel are not trustworthy, you can order a entire control unit. This can be done on the official website of the manufacturer or in a specialized online store. Setting a fee to the place of burnt usually is not difficult.

Most modern models equipped with mechanical regulators do not provide for their disassembly and cleaning. Primary repair consists in removing pollution from the outside, removing contact carts and stripping of plate-outputs on the regulator or timer. If this does not help or helps not fully, the part should be replaced.

Some old models allow cleaning mechanical regulators, after which the latter work perfectly, without complaints. Service must be carried out using non-aggressive solvents, for example, white spirit or a weak solution of ammonia. Cleaning oxides from contact groups should be a very small skin, special primers are used to eliminate traces of corrosion.

This is a detail that is often changed, including when the gas oven repair is repaired. Interference in the design of the device is not provided for. The element is replaced entirely.

Fans of blowing and grill over time cease to create a high.Quality air flow. If the engine works, then the impeller should be cleaned. Dust constantly accumulates on it, while on blowing fans. Fat and oil.

After a certain service life, it is necessary to disassemble the oven and lubricate the engine, if this is provided by its design.

In the case of the extinguisher failure, rewinding or other repair is simply unprofitable. The node is replaced entirely. Similarly act with the grill engine. It is placed in a non.Dissimilar case with the gearbox.

The heating elements of the oven constantly work in critical mode. Determine whether the heater works is quite simple. To do this, turn on the oven for the corresponding heating mode and check the temperature by touching the hand in the kitchen mittens. The method works, however, for a more accurate result, it is better to use a pyrometer. The device will clearly show the uniformity of heating over the area, indicate the maximum temperature in a given mode. This will diagnose a “burnt” heating element not only completely, but also partially.

Heaters are replaced after disassembling the case, buying the appropriate part is not difficult. A specific marking can be found after removing the heater or according to the reference data of your electric admiration model.

The last three elements that change without doubt and fluctuations are a backlight lamp, heat.Subject and sensory film panel. All these parts are not subject to cleaning and repair.

The operation of an emergency mode will be reported to the operation of the oven, and the problems in the operation of the film touch panel are diagnosed by the lack of reaction, the need to exert excess pressure, and random operations. The backlight lamp can be replaced independently, but to install new thermal guide or film sensor, it is better to contact the master.