How to drain water from the refrigerator beko

Indesit refrigerator how to drain water

Refrigeration equipment needs periodic defrosting. The life of the household appliance depends on how adhere to the operating rules. The instructions for defrosting the two.chamber refrigerator “Indesit” will help to correctly carry out the procedure and avoid faults.

  • Instructions for defrosting the refrigerator “Indesit”
  • Disconnecting the refrigerator “Indesit” for defrosting
  • Release from products, shelves
  • Waiting for defrosting
  • Washing and drying
  • Inclusion after defrosting
  • Possible problems
  • Malfunctions of the defrosting sensor and the Indesit refrigerator timer
  • The refrigerator does not cold after defrosting
  • Auto riverbell does not work
  • Frequent questions of consumers
  • How often you need to defrost the freezer “Indesit”
  • Where water flows during defrosting
  • How much the refrigerator needs to be defrost

Instructions for defrosting the refrigerator “Indesit

There are three types of household models of Indesit refrigerators:

  • Equipped with an option of auto.breeds No Frost, both in the freezer and refrigerated compartments.
  • Mixed type (freezer with “No Frost”, refrigerator compartment. with a drip defrust).
  • Devices providing manual defrosting of chambers.

Despite what your refrigerator model is old or modern with No Frost, the electrical appliance must be defrosted at the first signs of ice or hoarfrost. The ice layer prevents the stable and safe operation of equipment.

How to Clean Water Drip Pan of Refrigerator | Samsung 192L

Thaw the refrigerator correctly in the cool season of the year: in winter, spring or autumn. In the heat it will be necessary to make more efforts to install in the cells of the optimum temperature.

Disconnecting the refrigerator “Indesit” for defrosting

The instructions for defrosting the two.chamber refrigerator “Indesit” at the first stage provides for the disconnection of the device. Set the temperature controller in a zero position and remove the shtepsel from the outlet.

Turn off the electrical appliance is mandatory: in the process of defrosting, the refrigerator will be in the open state, the cameras will be filled with hot air, the motor will work hard.

This will lead to an increase in temperature and the failure of the engine.

In addition, the refrigerator turned on during defrosting increases the risk of water entering the current elements. This can lead to a short circuit and shock. When disconnecting, you need to place the plug of the power cord higher so that the moisture does not fall on the connecting element.

Release from products, shelves

The next step is to extract products, containers, shelves from chambers. Food must be placed in a cold place, especially perishable. You can put products in thermal packets or containers with ice or cool water. If you leave the contents of the refrigerator inside, then during defrosting, products will cool the surrounding space and slow down the course of the procedure.

Shelves and vegetable boxes, removable cells should also be removed. It is easier to remove pieces of ice from an empty chamber. During thawing, the extracted equipment can be washed and dried.

Waiting for defrosting

There are several ways to quickly defrost a two.chamber refrigerator “Indesit”:

  • Place vessels with hot water in both chambers.
  • Fill the refrigerator with heating pads or plastic bottles with boiling water.
  • Warm areas covered with hoarfrost or ice, using a hairdryer.
  • Put a heat gun or fan opposite the refrigerator.
  • Wipe the walls with a rag or sponge moistened in hot water or soap solution.
  • Spray the device from the inside with hot water using a spray gun.
  • Increase the temperature in the kitchen, turning on heating devices, plate.

Water in the process of thawing will definitely go beyond the boundaries of the chambers. Lay out pieces of well.absorbing tissue moisture around the device (old terry towels or microfiber shreds are suitable). Rags need to be placed inside the cameras.

There is no need to wait until the ice turns into the water: hoarfroll, lagging behind the walls, brush a wet sponge, and put pieces of falling ice into the sink.

Washing and drying

When thawing is completed, wipe the chambers with a dry cloth. After that, you can start cleaning the refrigerator from contaminants inside and outside. A small fat-blade plaque is able to remove a weak solution of dishwasher for washing dishes (2 teaspoons for a glass of water).

For cleaning equipment with No Frost, it is also permissible to use both home.made and ready detergents. Use the same composition as in the case of a regular model, or purchase a spray, wet wipes, etc. D. Specially developed products not only clean the surface well, but also disinfect.

If there are more serious pollution (spots, stains and smudges) such folk remedies as laundry soap, hydrogen peroxide and food soda. Do not forget to neatly clean and sealing tape. It is important not to abuse aggressive chemicals and compositions with abrasive particles to avoid damage to the body.

When working with detergents, be sure to protect the skin of the hands with household gloves made of impermeable material (rubber, nitril, latex, polyethylene).

Upon completion of defrosting and cleaning, leave the refrigerator door open for a certain period of time until the moisture is completely evaporated from the surfaces. Also check the tightness of the sealant: it is necessary that it fit tightly along the perimeter of the door, leaving no gaps.

Inclusion after defrosting

You can’t connect the refrigerator to the network right away. Device with mechanical or drip thawing after drying close, turn on and leave for 2 hours. Then load the shelves, boxes and products.

The minimum time in the disconnected state for the automatically thawing devices “No Frost”. 12 hours. It is better to leave the refrigerator for a day. If you do not follow the rules on turning on the device, the compressor and the engine may come out of the system.

Function and structure of drainage in the refrigerator

The drainage system needs a refrigerator to remove moisture. For models with a crying evaporator, this is condensate, which forms on the back wall of the refrigerator. At the bottom of the camera, in a special groove on the wall, there is a drainage hole. It is in it that all moisture should be normal.

Down from the hole, already outside the refrigerator housing, a plastic tube leads. On it, water flows into a special tray. It is located on the compressor housing.

When the motor heats up during operation, it heats the container with condensate, and it evaporates the kitchen in the air. Thus, the drainage of the refrigerator, with its simple structure, plays a crucial role. Moisture, scondmented from the air of the refrigerator, does not accumulate inside and does not fill the engine from the outside. Under the influence of natural physical processes, it is displayed out.

To maintain the normal functioning of the refrigerator, it is necessary to regularly clean the drainage system. This is a small tube connecting the camera and water capacity located near the compressor. If the tube is not clogged, it is recommended to wash the clipping of clogs. This must be done regularly to avoid a breakdown of the refrigerator.

Methods of cleaning the drainage hole in the refrigerator

How to clean the drainage hole in the refrigerator with a special brush

To cleanse drainage plum, you should use a special brush. Such devices are sold in plumbing stores. Instead of a brush, it is permissible to use a cotton wool.

How to clean a drainage hole in the refrigerator with a medical syringe

It is permissible to cleanse the drainage hole with the help of warm water, which is injected into the tube with force. This is done after defrosting the refrigerator. It is worth carrying out the procedure several times. In this case, in water it is worth diluting the detergent.

How to clean a drainage hole in the refrigerator with a rubber pear

Pear is sold in every pharmacy. To do this, clean the prepared tool with warm water and place in a drainage hole. After that, sharply put on a pear.

How to clean a drainage hole in the refrigerator with a thin wire

For this method, you should defrost the refrigerator and leave to dry for 6-10 hours. Then prepare a long wire. It should be thin. This device should push the remnants of the products.

At the same time, it is important to be careful to avoid damage to the tube.

Plum cleansing is performed from 2 sides. Then rinse the hole with warm water. To achieve better results, it is permissible to remove the drain pipe. This will help to achieve a good effect.

How to clean a drainage hole in the refrigerator with a cotton wool sprint

Turn off the refrigerator from the outlet. Before you start work, turn off the refrigerator from the network and remove it from it for fruit-vegetables.

Clean the drain hole. If there is no ice around the drainage opening, try to clean it with a cotton wool or such an unfortunate object. The configuration of many models includes a special device designed for this purpose.

Flotry the drain. Take a small sprint with warm (not hot!) with water and injected water several times into the drain hole. If the water successfully goes into the bath for collecting condensate, congratulations, the blockage is eliminated.

If these actions did not bring the desired result, and all the water from the sprint spils back into the refrigerator, most likely, the drainage hose is free, and without complete defrosting of the refrigerator, you can not do.

Cleaning the drainage opening in the refrigerator of the drip type

Independent cleaning of the refrigerator condensate tube requires maximum accuracy. Otherwise, the water will be released through the damage, and the device will become unusable.

If the drain is clogged in the refrigerator, then perform the cleaning of the drainage with your own hands in stages:

  • Turn off the device out of the outlet.
  • Remove the products.
  • For the convenience of manipulations, remove the shelves and boxes.
  • Move the device from the walls to see the location of the drain pipe from transparent plastic: from the center of the case to the tray on the structural block (compressor) located at the bottom of the refrigerator.
  • Prepare a brush to cleanse the drain (can be supplied with a set) or cotton sticks.
  • Remove the dirt from the tube, moving deep.
  • Type a small amount of warm water into a syringe or sprint.
  • Wash the capillary pipe with water under pressure. This will release drainage from the residues of pollution. At this moment, it is important to ensure that the water does not transfuse through the container on the compressor. Otherwise, the motor will burn.

If the water does not pass from the syringe, then the pollution has accumulated deeper. In this case, it will require cleaning with a thin long rope (soft, easily bending). Deep cleaning of the opening holes for draining the water in the refrigerator passes in several stages.

How to clean the drainage pipe in the refrigerator:

  • Twist the end of the wire into the loop so as not to pierce the drainage tube.
  • Paste.
  • Slowly rotating the wire, push it into the drain.
  • Pollution should advance through the channel to the container.
  • Rinse the removal of water under pressure (you can use a pear or syringe).

This method of cleaning the refrigerator drainage system is suitable for all models that are not equipped with the Know-Frost function, for example, Atlant, Whirlpool, Biryusa, and others.

When eliminating the blockage from the drainage, it will not work to completely get rid of the specific smell. It is problematic to remove the remaining microbes with simple water, and the use of improvised cleaners is not recommended.

How to clean the drainage pipe in the refrigerator of the know-frail

Cleaning the drainage opening in the refrigerator with the know-frast system is slightly different from the procedure for eliminating contaminants in ordinary devices. In models such as “Beko”, “Samsung”, “Liebherr”, “Indesit”, “Bosch”, Daewoo, Vestfrost, LG, the drain pipe is located behind the protective panel. Before removing pollution, it is necessary to dismantle the back wall.

Therefore, cleaning the tube in the refrigerator with No Frost is associated with the risk of damage to the protective panel. You can break the fasteners or the wall is incorrectly dismantled. Otherwise, the procedure is no different.

Water does not leave in the drip refrigerator

Refrigerators with a drip system have their own characteristics. Accordingly, there are specific reasons for the accumulation of water under containers for vegetables and fruits. Below we will describe the two most common.

Storage of products

There is no forced blowing in refrigerators with a drop system. Therefore, the air is weakly mixed, the temperature in the chamber is uneven. Especially if the products are located close to the walls.

Cleaning fridge drain holes | by Beko

At the same time, air circulation is difficult, near the walls is colder than in the chamber. Due to the temperature difference, condensate accumulates on them. It flows down and gets under vegetable boxes. If the drainage is located on the back wall, moisture will have nowhere to go.

Freezing the walls

If water accumulates under boxes, inspect the back wall. It should not have hoarfrost, ice or snow on it. When the compressor turns off or you put something warm in the refrigerator, the ice starts to melt. Water flows down and accumulates under the boxes.

To get rid of ice or hoarfrost, you need to find the reason for its formation. We wrote more about this in the article: why the rear wall of the refrigerator freezes: we are looking for a reason and eliminate.

Water accumulation places

One of the useful inventions of our time is refrigeration equipment that allows you to save products fresh and make blanks. Expansion of the functionality of emanated brands (Liebherr, LG, Sharp, Hansa Fy, Hitachi, Siemens, Shivaki, Mitsubishi, Samsung) allows even to receive ice, chilled and purified water: both ordinary and gas. But such “smart” units can break.

On the back wall

The “Crying Wall” is suffered by devices with a drip system of defrosting (Liebherr CNEF 4815, Bosch KGE39XW2AR, Atlant XM 4625-101, Beko RCSK 335M20W, Whirlpool Art 9810/A, Indesit DF 4200 E).

This does not always indicate the problem of equipment, as it is an automatic defrosting cycle. All ice formed on the wall, then thaws, and melt water flows through the hole located below.

Sometimes the process is accompanied by gurgling, murmur, hiss and other sounds, this is normal.

But the appearance of a “snow cap” is already a violation in a freezing system:

    cooling mode for maximum value in hot weather;

  • Fostering the main department and the ingress of warm air from the premises, followed by the formation of condensate, due to the torn or old sealing gum;
  • A drainage hole is clogged;
  • Placement on the shelves of hot kitchen utensils without a lid.

Under the boxes

In units with cooling No Frost (Samsung RT60KSRVB, Daewoo FR 3501, Beko CMV529221 W, Bosch KGN36NL14R, IndESIT DF 5181 x M), a capacitor is collected when defrosting module (under vegetable boxes).

  • constant operation of the engine-compressor;
  • Big “snow cap” in the freezer;
  • flowing yellow liquid from under the door seal;
  • Sometimes, there is no cooling in the main department.

Under the refrigerator

The accumulation of liquid under the device itself on the floor may be the result of sloppy movement or transportation, as a result of which the following damage occurs:

Water accumulates in the pallet of the refrigerator Beko CN 329120

It is elementary that you just need to wash it and defrost it for a day.

Find a drainage hole and blow it.

The drainage hole is in the refrigerator and freezer compartment

Hello. Initially defrost the refrigerator during the day. Then look for the hole of the drainage system. blow it.

You need to defrost the refrigerator very well.And if you want to find drainage, then the second end of the drainage is behind where the compressor costs.you can clean the wire from there, but most likely everything just froze.

The first plosmass on the ledge, the second on self.tapping screws, then unscrews the end, remove the connector on the Winter and there will be (according to your radiator) if he is all in the ice that is unlikely to be defrost, if there is no tan with the left under the aluminum in aluminum there and try to put the wire and then pour water and look leaves or not.

Similar questions

Problems with the Beko GNE 134620 X refrigerator more than a year ago Beko Gne 134620 x refrigerators

After connecting the refrigerator to the water supply through the filter (Aquauphorus Trio), began to drip a water supply tap for the water supply (1 drop.

The Beko refrigerator does not close the door more than a year ago Beko Cne 32100 refrigerators

At the refrigerator Beko Cne 32100 does not close the upper door. I would like to close it myself without calling the repairman! Is it possible and how it is.

Thank you for competent answers in the past question! Beko CN 335220 refrigerator control module.He is located where the motor is?, In the schemes he.

  • Service center
  • Service Center Miele
  • Repair of Sony Bravia TVs in St. Petersburg
  • Repair of binoculars
  • Service Center Dzhilex
  • Service centers of the DNS
  • Redmond service center
  • DEXP V890
  • Cartridge Cartridge Krasnodar next to me
  • Where you can refuel the cartridge for the printer
  • Epson service center
  • Bosch service Gelendzhik
  • Samsung service center
  • BORK service center
  • TV repair in Serpukhov
  • Circulation of the Kaluga cartridge
  • Taxing cartridges Tomsk
  • Heat Flower Lipetsk
  • Repair of a juicer
  • Repair Bluetooth headphones

Hello, the refrigerator “Bosch Duo System” burns and flashes t-ra 6, there is no ice, it stopped cooling; Frost t-ra.20, frost. Tell.

The problem with the treadmill more than a year ago Kettler’s Running paths

Help! The problem is in the treadmill, the engine burned out a new one, in the engine control unit he heats up very quickly.

The laptop of the cause of the HP Pavilion 15-B052SR laptops spontaneously turned off

Hello! Briefly, the problem with turning off the HP Pavilion E-15 laptop. I turn on the laptop, everything is remarkably turning on any game, it works.

Problems with the phone LG X Power K220DS more than a year ago LG X Power K220DS cell phones

Please tell me, in the area of ​​the camera something rattles, you can still hear when you switch the modes by the camera.Smartphone week from day.

The keyboard is periodically ceased to work more than a year ago Maizu M3 Note cell phones

The Meizu M3 Note phone periodically stops working, the sensor works letters click but not printed, a little passes.

Sony DAV-DZ840M home theater more than a year ago does not turn on home theaters of Sony DAV-DZ840M

Good afternoon! Stopped turning on! I would like to know how much repairs will cost in Buzuluk. Most likely T5ah fuse burned down.

The phone does not catch a mobile network more than a year ago Samsung Galaxy S6 cell phones

Please tell me, the Samsung Galaxy S6 phone does not catch a mobile network (after falling). it can be fixed?,If so, how much can it.

The vacuum cleaner works very loudly and quickly turns off more than a year ago Electrolux Cyclone Power Z5810 vacuum cleaners

Good afternoon! Vacuum cleaner, once turned on without a filter. Then he began to work very noisily and quickly disconnect. The engine clogged.

We need brushes for the electric motor of the washing machine more than a year ago Washing machines Hotpoint-Ariston Arxl 105

Where in Tomsk you can buy brushes for the HotPoint-Ariston ARXL 105 washing machine? Engine model. “Welling” “HXGN21.07.

The Huawei Y541-U02 phone does not turn on the huawei ascend y541-U02 cell phones more than a year ago

Good afternoon! I turned off the Huawei Ascend Y541-U02 phone and it no longer turns on. Only the emblem on the screen of the phone lights up and that’s it, on.

drain, water, refrigerator, beko

On the first day of the purchase of the detergent vacuum cleaner Zelmer, after 2 hours of wet floor cleaning, the engine stopped turning on. When turning on.

Good afternoon! Help to choose a Wi-Fi adapter for TV Philips 40PFL3108T 60. Thanks.

The problem with the Canon EOS 1100D KIT camera more than a year ago Canon EOS 1100D Kit digital cameras

Defrosting of the refrigerator Beko

The Turkish manufacturer “Beko” offers customers various models of cooling devices:

  • Two.chamber refrigerators with a freezer located above or below;
  • Side by Side (side-o-box);
  • multi.door models;
  • Freezers.

The cooling system can be static or “No frost”. It depends on this how to defrost the refrigerator Beko.

With a static system, manual defrosting is required. The moisture that appears in the device during operation accumulates on the back wall, then flows down and is removed along the drainage hole. A tray for collecting condensate is installed on the back wall for this. Sometimes moisture drops freeze, and an ice crust appears inside the technique. To get rid of it in a timely manner, and you need to defrost the refrigerator Beko.

In cooling devices with the No Frost system, a radiator is installed in the camera.

The air flow is distributed evenly and passes through the evaporator. Then also removed from the camera. Thanks to the same temperature in all parts of the chamber, condensate does not freeze, and therefore not to defrost the refrigerator Beko in the traditional sense is not required: this happens automatically. It is necessary to periodically wipe the walls of the camera with a soft cloth, and turn off the electrical appliance once a year to wash.

Secrets of proper defrosting

To correctly defrost the refrigerator “Becco”, you need to turn it off from the network. Extract products from cameras, remove all shelves, pull out boxes. After well washed the electrical appliance.

Other tips on how to defrost the baco’s two.chamber refrigerator:

  • If ice forms on the wall of the refrigerator, you must wait until it thaws. You can’t use sharp objects for this.
  • Be sure to check if the drainage tube is clogged. If this happened, you will need to blow out using the device that is included.
  • Peel the compressor on which the condensation flows on the back wall.
  • When washing, use any detergent except abrasives. The manufacturer, giving advice on how to defrost the refrigerator Veko RCSK335M20W, advises all the parts to wash the baking soda (a teaspoon for a glass of water). This will additionally get rid of extraneous smells.
  • Rinse the shelves and boxes after washing in the bathroom or in the sink under the stream of warm water.
  • Wash the walls of the chambers well with a clean rag, then wipe it dry. Leave them for a while open.

Beko Washing Machine not Draining Water. Fixed

It is important that before turning on the device, all the washed parts are well dried. This will prevent the appearance of mold and unpleasant odor in the future.

The recommended frequency of defrosting the cooling technique of “Becco”

The period of defrosting the Beko refrigerator depends on the type of cooling. The device with a static system should be turned off at least twice a year. This is indicated by the instructions for defrosting the refrigerator Beko.

But there is an additional condition. Beko has to defrost often if ice is formed on the walls of the freezer with a thickness of more than 7 mm. The reason for this becomes improper storage of products: in open form, without packages.

The technique equipped with the No Frost system is enough to turn off for preventive washing and ventilation once a year.

Instructions for the correct defrosting of the freezer “Beko

Thawing ice should naturally occur. You can not use sharp objects (knives, forks), hair dryer, special aerosols for defrosting, containers with very hot water to speed up the process. In this case, the ice will thaw quickly, but from the mechanical exposure and a sharp temperature difference, the technique may become unusable.

Periodically you need to collect water from the bottom of the freezer. You can spread a rag, well absorbing moisture for securement next to the refrigerator.

The final stage is washing and wiping the walls dry. This is one of the rules that need to be followed in order to correctly defrost the Beko freezer. Otherwise, the remaining drops will immediately freeze.

Defrosting. operating instruction Beko CSE 24007

A) the camera of the refrigerator of the lodging chamber is defrosting automatically. During the refrigerator operation, draining drops of water can form a layer of ice up to 7-8 mm thick on the back of the refrigerator chamber. Such ice is a common occurrence that is associated with the features of the cooling system. This ice is periodically removed using a system of automatic defrosting, which is located on the rear wall of the refrigerator. The user does not need to clean the ice himself or wipe the drops of water.Melt water, which is formed during defrosting, flows through the gutter into the drain tube, falls on the evaporator and evaporates there. Check regularly if the drain pipe clogs, and if necessary, clean it with a stick through the drain hole. Automatic defrosting of the freezer is not provided, as this can lead to damage to frozen products.

B) the freezing camera is produced simply and without creating a mess, thanks to a special tray of gathering thawed water.Make defrost twice a year, or when an ice layer reaches a thickness of approximately 7 mm. To start the defrosting procedure, turn off the device and remove the power cord from the outlet.All products should be wrapped in several layers of the newspaper and placed in a cool place (for example, in a refrigerator or a pantry for products).To accelerate defrosting in the freezer, you can place containers with warm water.

Do not use sharp objects for removing ice, such as knives and forks.Do not use hair dryers, electric heaters and other similar electrical appliances for defrosting.Melt water accumulated in the lower part of the freezer, get wet with a sponge. After defrosting, wipe the inner surface of the refrigerator dry. Insert the power cord into the outlet and turn on the power supply.

How to rinse from the devices with no frost?

In modern kitchen appliances equipped with the No Frost defrosting system, a contaminated drainage hole contributes to the formation of a snow layer, ice at the bottom of the freezer.

With an increasing load on the compressor of the device, the refrigerator performance is noticeably reduced. As a result of prolonged operation of the motor in an enhanced mode, the equipment may fail.

Since the drain hole in the refrigerators of this type is behind the protective panel, its cleaning is a very complex and associated with the risk of improper dismantling of the details of the device.

Therefore, in the case of clogging of the drainage system of the unit with the No Frost system, it is advisable not to act independently, but to seek help from the service center and call the master at home.

REFERENCE! In many cases, the deterioration of condensate drainage is associated with freezing of water in the drainage hose. To eliminate the problem, de.energize the device for 48 hours: frozen moisture in the tube thaw and condensate will pass without hindrance.

If you are interested in how and how to remove dents on the surface of the refrigerator, read this article.

Useful tips

To prevent a humidity in the refrigerator and reduce the number of purges of the refrigerator’s drain system, adhere to the following rules during the operation of the household device:

  • regularly perform the procedure for washing inner surfaces, which will eliminate the accumulation of garbage in the chambers;
  • Place the products on the regiments of the unit at a short distance from the walls of the compartments so that packaging material, products do not touch them and do not freeze;
  • Periodically examine the drainage opening and clean it if necessary with cotton sticks, ruff or pressure of warm water with rubber pear.

The problem of clogging of the hole and tube for removing condensate is not a serious breakdown, but rather refers to the procedure for servicing the device.

If during the work of the refrigerator you began to notice at its bottom small accumulations of water. without delay, proceed to clean the drainage system.

drain, water, refrigerator, beko

Eliminate the cause of water in the refrigerator with a drip type of defrosting

If there is water in the refrigerator, but the device continues to freeze, this is not about a malfunction, but a violation of the rules of operation of the refrigerator.

In most cases, puddles arise in the refrigerator due to the blockage of the drainage system, which is easy to eliminate with your own hands.

IMPORTANT! For safety reasons, the blockage should be eliminated after turning off the power supply of the refrigerator.

If the drainage hole is covered with ice, the refrigerator must be thawed. Perhaps meltwater will go into a thawed drainage hole. Then it remains to just rinse the drain by pouring warm water into it.

If the water is worth it after defrosting, as well as in cases where there was no ice initially, it is necessary to restore the cross.country ability of the drain hose. For work you will need:

The blockage in the upper part of the drainage tube can be eliminated with a cotton swab or a device provided for by the configuration of the refrigerator. You can check the effectiveness of actions, filling a little warm water into the wastewater. If the water quickly ran away, then the cross.country ability is restored.

Sometimes a short cotton wool and similar devices do not help water to leave. So the blockage is located below. Flexible aluminum wire of suitable diameter will help to break through it.

Cleaning fridge drain holes | by Beko

ATTENTION! The end of the wire must be bent so as not to pierce the silicone drainage tube.

The wire must be pushed into the hole so that its end appears on the bottom of the hose located behind. This is the only way to be sure that the water wars freely into the capacity provided for this.

On top of the wire can stumble upon an obstacle and not move on. In this case, you can break the blockage from below. You need to do this without making excessive efforts, so as not to perfume the drain hose.

Когда проходимость трубки восстановлена, в гигиенических целях её нужно промыть тёплой водой с добавлением соды или капли моющего средства.

IMPORTANT! It is better to bring the lower end of the drainage tube to a small bucket, since the water collector, designed for a small amount of water, can be overflated.

How to prevent water in the refrigerator

The water constantly standing in the refrigerator leads to the appearance of mold, the reproduction of fungi, bacteria. Storage of products in such conditions is unacceptable.

To avoid the appearance of water, several rules must be followed.

  • Observe cleanliness in the refrigerator. Timely wash regiment and boxes, wipe the back wall.
  • Regularly defrost the freezer.
  • Make sure that the refrigerator closes tightly. To do this, it must stand on a flat surface, the sealing gum should be a whole. Only packaged and closed products in the camera. Open containers increase humidity in the chamber, and the moisture condenses abundantly on the back wall.
  • Do not put warm and hot products in the refrigerator. The compressor in such conditions is forced to work for a long time without disconnecting, and the back wall will freeze too much. During thawing, the water accumulates and can result in a groove for drainage under the boxes.
  • Do not put products back to the back wall. There they will change, and the evaporator will be covered with thick hoarfrost and will not quite effectively cool the air in the refrigerator. When thawing, a lot of water is formed.

Having discovered water at the bottom of the refrigerator under boxes for vegetables and fruits, the hostess should think about how carefully she relates to her technique. Wipe the puddles in the refrigerator daily. this is not a way out, you need to find and eliminate the cause.

Most often get rid of water accumulation in the refrigerator on its own. If the methods described above did not give the desired result in the refrigerator, you need to contact a refrigerator repair specialist.

About the author

| Denial of responsibility | Contacts |RSS