How to shorten pants without sewing
Cobbler can not be used for all types of material. For example, it is not desirable to use it when hemming knitted pants, as the materials are very elastic and with the webbing can lose its stretch. It is also better not to use webbing on thin fabrics. It can thicken the product, creating extra volume. As for expensive materials, it is better to entrust the work of hemming things to a specialist.
Other types of fabrics can be easily processed by means of cobweb.
Attention! One of the big advantages of using duct tape will be that the threads will not be visible from the outside of the pants.
- Turn the trousers on the wrong side;
- Bend to the desired length;
- Place a piece of webbing between the crease and the pant leg;
- From the wrong side go through with a hot iron.
If the webbing is of poor quality, it will not glue the places. Therefore, you will need to use duct tape and spray it with water.
In stores, there is a tape, which is applied to a paper base. Such cobweb has several advantages in comparison with the classical cobweb. The thing is, it’s hard enough to put it in the right place. Much easier to do if it has a paper backing.
Tape is inserted into the bend and ironed several times at high temperature. Therefore, it is necessary to heat the iron strongly. Tape melts well and glues the fabric together.
- Practical application proves that the tape can peel off after three washes. In this case it has to be glued again. Therefore, you should try not to contaminate things;
- When washing, the water temperature should not be more than 50 degrees;
- Sometimes in the process, the cobweb sticks to the iron. A small scrap of fabric soaked in alcohol is needed here. It removes tape residue well. In order not to stain the iron, it is advisable to put a bandage or cotton cloth.
How to beautifully hem pants on the sewing machine and by hand: simple ways for novice crafters
Sewing up pants is not always as easy as it seems. In any atelier you will hem them quickly, on a special machine, using a special transparent thread (monofilament). That’s why the hems are invisible on the front side. But why go to the atelier, when you can twist and hem the bottom of pants with tape with your own hands? How to neatly hem pants at home you will learn from this article.
First let’s look at the general techniques used for this operation.
Pants hemming technique
Methods using duct tape and blindstitching are described in the relevant articles, which are linked below, but here we will touch on the most simple hemming using a sewing machine.
After measuring and marking we trim the excess fabric. The resulting edge should be overlocked. so it spoils less and retains a nice appearance.
Now more about the steps of hemming pants:
- The first thing to do is to sweep the trouser tape at the level of the trouser fold;
- Stitching is carried out on special textured strips around the circumference;
- When you have gone all the way around the circumference and are close to the overlap of the ends, you should lower the needle and raise the sewing machine‘s foot;
- Across the ribbon, stitch and then move on to sewing the other edge of the ribbon;
- Now iron out the pant braid;
- Bend the pant leg and sew with a suitable thread, or make a blind stitch by hand;
- iron the seams and enjoy a great pant.
How to sew a pant braid on a sewing machine
Before I explain in detail about blindstitching, I want to briefly explain how to sew a trouser tape. The tape is sewn on the sewing machine with two stitches. Sewing it on is not necessary, the main thing is to stretch it correctly when sewing. Otherwise the tape can either pull the bottom of the pant, or vice versa, stretch and you can not fix this defect with an iron.
Words are difficult to explain the degree of tension of the tape, this requires practice. But the general idea is this.
If the tape is loose, the edge of the pant will be wavy. And vice versa, if it is too tight. narrow.
How to Hem Pants by Hand. Step by Step
It is best to pull the ribbon and fabric lightly at the same time with little effort. Only to ensure that the ribbon is sewn evenly on the fabric without deforming it.
Never do this operation last. Better postpone until the next day.
A carelessly sewn hem at the bottom of the garment will ruin the whole look of the garment. All the more so because inexperienced seamstress sometimes have to redo the work.
How to hem pants with a sewing machine
If you have a sewing machine, sew a pant ribbon all around or around the back of the garment first, either by pinning it in place or by hand, so that the pressed edge is at the very bottom. Stitch at a distance of 1-2 mm from the edge.
The lace should be steamed and dried before use. Can be sewn with an iron and steamer. If not, moisten the tape with hot water, straighten and dry it. Unprepared hemming can later give shrinkage and deform the bottom of the product.
Tape the bottom hem so that the sealed edge of the hem is exposed underneath it as an edging. This is to prevent wear and tear on the fabric when in contact with shoes. Along the fold, place the purl stitch by hand, then iron the bottom of the pants, covering the fabric with moistened gauze so that the front side does not leave shiny traces from the iron. You can iron from the wrong side, adjusting the heat so that the braid does not melt. In this case it is enough to activate the steam mode, it is not necessary to cover the garment.
HOW TO HEM PANTS | Shorten Pants Without Sewing Machine
Draw a chalk line along the front side to guide the stitching along which the machine stitch will run. On white fabrics the fishing line is laid with a hand overcasting stitch. The garment is sewn with a sewing machine, the tack is removed, and the bottom is steamed with an iron.
To hem the pants on the machine, it will be more convenient to use the sleeve platform. If the equipment is an old type, the fabric will have to turn inside out and stitch in short sections, moving under the foot every 5-7 cm.
If the fabric is dense enough, to fix the seam allowance of the bottom, lay a countersunk stitch by hand, capturing the needle 1-2 threads of warp from the wrong side. The fabric should lie flat, without any knots. In this case, the stitch will not be visible on the front side.
How to hem pants or shorts. No sewing machine. Sew a hem by hand Easy hemming tutorial
How to hem knit pants
Knit pants can be sewn by machine or by hand. If you do not have a special foot, then cut them to length, bend them first indented 5-6 mm, then bend the fold again and sweep. You should have two stitches. Iron with a steam iron, stitch with a machine. Can be hemmed by hand. What kind of stitching? Here is a good stitch “goatskin stitch”. It will not allow unraveling the hemming, even with heavy wear of the product.
If you don’t have a sewing machine, the same stitch can be used to hem any sweatpants.
How to hem jeans correctly
Everyone has jeans in their closet, most of us have several pairs. Wide and narrow, classic indigo and shabby to pale blue. it’s easy to find your dream pair. And if size, thanks to the abundance of choice and stretch fabric is not a problem, the length has to be adjusted in every other pair. On how to do it correctly, creatively and easily tell us about this article.
How to sew the pants at the waist
There are several ways to reduce pants around the waist.
Sewing on the hems
Trying on a thing and evaluating how much the product will be sewn. Often the extra fabric will be reduced by the darts. Either the old ones are unraveled, or new ones are added.
Pants are ironed, then fitted. Excess fabric is marked on the pants. The edges of the darts may rest on the side seams, but avoid it. Otherwise ugly folds and skewed pieces are possible.
Open the seam and the waistband. Sew in the seams as needed. Cut off the excess. Sewing darts with a sewing machine.
The belt itself is cut at the sides. Cut off excess fabric. Sew the edges of the garment and the belt. The belt is sewed neatly to the garment along the lines. Attaching the strap.
Reducing at the expense of the back seam
Several sizes are reduced at the waist by a back seam. After trying on, the eyelets (belt fasteners) and the waistband are torn off. The waistband is cut in half.
Stitching on the middle seam is ripped. The seam is sewn at the marked distance. Belt is reduced, processed. Sewed with a sewing machine. It is sewn to the main garment. The stitching is reinstated.
Full re-stitching
The most time consuming variation and will affect the whole garment. Remove the shoulder stitching in the necessary places. Often in the back part of the fabric. Remove the belt by a few centimeters (10) on each side.
Stitch in the seam at the bottom of the seam. The middle seam is also ripped. Secure everything with pins to avoid displacement.
At the waist, you need to indent the middle stitching by 2 cm. Conducting a fishing line for the future seam. Should be a triangle.
Stitch on the sewing machine and trim the edges. The step seam is sewn. At the waistband cut off the excess. Work the edges and sew back on. Attaching the stitching.
Instructions for hemming with preservation of the factory seam
An inseparable element of clothing is a decorative stitching. Many people, buying jeans that fit them perfectly at the waist, but have the wrong length, wonder how to keep the factory trim.
This requires adhering to the following order of action:
- Determine the length and width of the hemming on the wrong side;
- Lay out the garment and straighten out all the folds;
- From the planned length measure up the width of the hem;
- Draw a line parallel to the floor and 1 cm down;
- Draw a second fishing line and perform all the above steps on the other pant leg;
- Perform trimming on the second mowing line;
- Take the scrap with the factory stitching and set aside 1 cm from the hem;
- run a mowing line and cut off the excess.
Jeans should be hemmed with the seam retained as follows:
- To the pants to attach the details with trim;
- Level the seams and staple inside and out;
- Carefully sweep off the details;
- Sew from the factory seam in 1 mm;
- make a cut of the seam allowance to the stitching a few millimeters before;
- trim bottom seam allowance to 4 mm;
- to the hemming, baste the edges;
- from the factory seam in 1 mm to stitch and overstitch the seam allowance.
This is a simple way to hem jeans while retaining the factory seam.
