The connection diagram of the boiler Buderus to the heating system
How to choose a location of a gas boiler? How much does the work of specialists in the installation of single and double-circuit devices cost?
Монтаж автоматики Logamatic 2107 котла Buderus Logano G124 WS
Installation technology implies the following sequence:
- Preparatory work.
- Placement of mounts and directly installation of the boiler.
- Connection to the water supply, gas and electric network (namely in this sequence).
- Connection with the chimney.
- Filling the system with water, checking, trial launch.
First of all, the gasification project is approved and implemented: gas is supplied, a ball valve, meter and trademer are installed (these works are strictly forbidden to do it yourself, only certified specialists have access). For power supply, a separate wiring is laid with the mandatory inclusion in the voltage stabilizer to protect the automation, it is also provided for providing a wall boiler with grounding. The presence of all the required components is checked, the instruction is once again studied. Before the start, the gas boiler, highways and radiators from garbage and extraneous particles are carried out. These actions are relevant both when commissioning a new system, and when replacing a heating device.
The kit includes a special bracket and latches, it must be taken into account that the latter are not always suitable for wall material, sometimes they are purchased separately. The choice of these parts is extremely important when installing a wall gas boiler, they should withstand a load exceeding the weight of all equipment. Fastenies are placed in parallel to the floor, as even as possible, otherwise the automation will fail. The boiler is hung on the wall, the level is checked and only if there are no distortions are connected to the heating line. The dismantling of the unit and drain the coolant using the appropriate locking valves is provided.
Elements of a heating boiler strapping
Knowing what elements are contained in the strain of the gas boiler of heating will help to easily connect heating equipment to the system:
- Heating boiler. It is one of the main components of the heating structure, the method of connection and the outline of the heating boiler is largely dependent on its choice. The heating boiler cannot be placed at the top of the pipeline wiring. The rod of the heating circuit should contain the ability to remove the air. To avoid the presence of air plugs, in the absence of a balloon in the boiler, the pipe should be placed vertically.
- Nozzles. This element has gas wall and electrical appliances designed to heat the liquid coolant (
Setting Adjusting Buderus boilers
All heat units need regular balancing and regulation of parameters. In most cases, a full range of such works is performed with the service of boilers. However, there are situations when unscheduled adjustment is required. For example, after an emergency stop, with a decrease in performance, with repeated errors issued by automation or after modernization of the system.
The specialists of our center are ready to carry out both a one.Time adjustment of your heat unit, and take it for long.Term maintenance. We are authorized to work with the entire model range of Buderus, and our masters have all the necessary licenses and certificates.
The control of the boiler includes events such as: warming; verification of the chimney and automation of safety; control and debugging of the ventilation system, supply and power supply supply. For all types of work, we provide an official guarantee.
To obtain additional information on all types of services provided by our center, you can call a round.The.Clock hot line on the phone or come to our office.
What boiler to install: selection criteria
In order not to make a mistake when selecting an unit for heating, experts recommend choosing a boiler according to the following parameters:

- The power of the device is the most important criterion. A weak boiler will not be able to effectively heed the house, and the most powerful of the time will work “idle”. Power is selected by heated area: 10 m². 1 kW of power.
- The next criterion is the type of fuel. Choose the most affordable and cheap energy in the region should be selected. Many models shoot this problem, working on most types of fuel.
- The material of the heat exchanger. Cast iron boilers have more durability, are not subject to corrosion, retain the temperature longer and are unpretentious in maintenance. Steel units have less weight and size, warm up faster, but are subject to condensation and, as a result, corrosion.
- The volume of the furnace chamber is the larger, the less often you have to “look” there, that is, to report fuel. Alternative. Boilers with automatic fuel supply allowing loading every 4-7 days.
Advice! Safety is also an important parameter. Therefore, you need to pay attention to the presence of automatic alarm and emergency shutdown when overheating.
Specifications
Consider the overall technical characteristics of single.Circuit boilers Buderus for 24 kW:
Parameter | Meaning |
Type of boiler | Gas heating |
Method of installation | Wall or floor |
Power | 24 kW |
Served area | Up to 240 m2 |
Type of fuel | Natural or liquefied gas |
Temperature in the heating circuit | 40-85 ° |
The pressure of the coolant | Up to 3 bar |
Gas consumption (medium) | 2.1 m3/h |
Power supply | Single.Phase, 220 in 50 Hz |
Setting Adjusting Buderus boilers
All heat units need regular balancing and regulation of parameters. In most cases, a full range of such works is performed with the service of boilers. However, there are situations when unscheduled adjustment is required. For example, after an emergency stop, with a decrease in performance, with repeated errors issued by automation or after modernization of the system.
The specialists of our center are ready to carry out both a one.Time adjustment of your heat unit, and take it for long.Term maintenance. We are authorized to work with the entire model range of Buderus, and our masters have all the necessary licenses and certificates.
The control of the boiler includes events such as: warming; verification of the chimney and automation of safety; control and debugging of the ventilation system, supply and power supply supply. For all types of work, we provide an official guarantee.
To obtain additional information on all types of services provided by our center, you can call a round.The.Clock hot line on the phone or come to our office.
Installing the Buderus Logano G115/4 boiler with Riello oil burner.
Simferopolskoye highway, self.Service automatic system
Provide with heat and hot water a self.Service automatic system, install a system of anti.Icing.
The specialists of our company are fully equipped and mounted a boiler room, supplying with heat and hot water a self.Service automatic machine, located in the south of the Moscow region. The floor of the Buderus Logano G215 WS Buder boiler is based on

With a capacity of 78 kW, it serves as a heat generator for heating the boiler and water warm floors. To control and monitor the system, a weather-dependent controller with the LCD display is installed, which allows separately control the heating contours, the burner of the German manufacturer GierSch working on diesel fuel, the mixing and mixing modules of Huch Entec, the Watts security group, the MEIBES Water Warm-Warmarometers. As a material for the installation of a water warm floor system, we use the Rehau Rautitan Pink pipe with a diameter of 20 mm.
Heating systems of country and country houses. Boilers, gas speakers, water heaters. Repair, service, operation. Installation and installation recommendations.
Connection of the boiler Buderus Logamax U072
Connection of the ON/OFF regulator or the Open-Term regulator
To connect the network wire, you need to open the control unit.
Buderus logamax u072 input in operation
1-slide hose, 2-cran of the return line of heating (additional equipment), 3-cran of cold water (additional equipment), 4-gas valve (closed) (additional equipment), 5-bit water, 6-cran of the supplying heating line ( Additional equipment), 7-band “Return” (get out of the service function/submenu without saving), 8-band “OK” (confirm the choice, save value), 9-display, 10-automatic air vent, 11-pen “”, 12-band “-” (Mode), 13-band “Stand-by-by”, 14-manometer, 15-device for filling out
Before entering the boiler Buderus Logomax U072 into operation:
1-work of the burner, 2-indication of the malfunction/indication of the standby mode (Stand-by), 3-mode heating is active, 4-supplies of hot water are actively, 5-active summer mode, 6-service mode, 7-index of temperature (С ° ° C)
Gas supply setting (natural and liquefied gas)

1-measuring fitting (pressure on the nozzles), a 2-regulating screw of the maximum gas consumption, 3-lump, a 4-control screw of the minimum gas consumption, a 5-tutus for measuring the supplied gas pressure
Gas pressure on nozzles with maximum thermal power
Checking and maintenance of the boiler Buderus Logamax U072
Cleaning the pallet of the burner, nozzles and burners SIT
Checking the expansion tank
With an annual check of the expansion tank, it is necessary:
Features of installation
As mentioned earlier, depending on the type of installations, there are various options for their installation, but it should be noted that all systems work on the principle of water heating during its circulation and direct interaction with heaters. As you can connect heating equipment with your own hands with your own hands?
There are standard classic schemes illustrated in the instructions for the installation of Buderus boilers of a series. However, in practice, the schemes almost always undergo changes to optimize the wiring, fitting to the geometry of the premises of the furnace and the mutual arrangement of individual units of the heating system.
The heating systems of country houses, although similar to each other, but only in general terms. In reality, how diverse are the areas and layout of the buildings, their heating systems are just as different. The departure from standard schemes can also be caused by:
- Connecting the heat exchanger heating of the pool,
- The placement of a volumetric buffer capacity to which you plan to connect alternative heat sources: heliocollectors, solid fuel boiler or a fireplace furnace with a water circuit.
The complications of the scheme cannot also be avoided when implementing the connection scheme of cascading boilers Buderus, when the system is designed to use several gas boilers working together or alternately. A modern approach to the construction of such systems is the use of special nodes. Hydraulic arrows that ensure the alignment of temperatures and the pressure of the coolant in several contours connected to it.