How to put air conditioner on heat Ballu Olympio

Ballu air conditioning instructions How to turn on heating

The fertile time of heat, summer and vacations, stuffiness and heat retreated, has passed, and lost the power of a working air conditioner. It is time to enable the installed air conditioning for heating.

The experience of previous years suggests that with switching the split system to heating mode, for some reason, difficulties often arise and simply dead end situations. To some extent, you can complain about some scarcity of descriptions in the instructions for operation, but most often our person does not even look into this very instruction, and more than 30% of users do not even know where it lies.

In this article, we decided to describe in detail the sequence of actions when switching the air conditioner from cooling to heating.

House heating by air conditioning. step.by.step instructions

First of all, we include our split system in the 220V electrical network. On the remote control (DU) we find the power button (“Power” or “On/OFF) and click it. As a rule, the internal block is supplied with a quiet sound signal. After this signal, in most cases, blinds open and the fan of the internal unit is turned on. This is fine.

On the remote control we find the “Mode” button.

On some models of Ballu air conditioners. Carrier, MDV and others. This key is simply indicated by the letter “m”. If such buttons were not found, then we will storm the instruction manual and find where the air conditioner is switching on the remote control.

The split system has several operating modes, each of the modes is indicated on the display of the remote control with its icon:

Sometimes, instead of pictograms, inscriptions appear: Dry, Heat, Cool, Fan.

We click on the “Mode” button several times. until the display of the remote control will appear the icon of the sun:. For some manufacturers, it is difficult to distinguish the sun from a snowflake. be careful.

Further, make sure that your air conditioner is generally able to work for warming up, then the “sun” on the display will not see at all.

After you have chosen the “sun” button on the MODE on the remote control, the fan of the internal unit may stop rotating, and the blinds may be closed. The air conditioner seemed to be silent, thought. This is fine!

Как правильно пользоваться кондиционером

On the remote control with arrows set the temperature, preferably maximum, degrees 30. Please note that if the air temperature in the room is higher than you put it on the remote control, then the split system will not warm!

The air conditioner will continue to remain in a “thoughtful” state for up to 10 minutes, this time is required to restructure the processes of work, you just need to wait and it is better not to press anything else. As it turns out in practice, to wait out this interval of time becomes the biggest problem, it seems to the user that he did something not that the air conditioner is “stupid” or he is not working.

After 5-10 minutes, the air conditioner suddenly “wakes up” and begins to blow with warm air-cheers, you did everything right!

I would also like to pay attention to the next nuance: during all these manipulations with the air conditioning, do not forget to direct the remote control to the internal block of the split system. It often happens that the signal from the remote control simply does not reach the response in the internal block.

If after all this your air conditioner did not warm, then you should contact the service service of the climate company.

Please note that in winter you can operate a split system to certain negative temperatures from the outside, usually to.5-7 degrees, read about this in our section “Question-answer”.

How to enable air conditioning for heating and warm air: setting, put and switch with a remote control

The old window air conditioners in the form of a monoblock were replaced by modern split systems. If the former could only work for cooling the premises, then the latter are also capable of heating it in the cold season of the year. But before turning on the air conditioning for heating, you need to familiarize yourself with the sequence of actions. The correct inclusion of the unit will be the key to long and uninterrupted operation.

Advantages and disadvantages of the heating mode

The “heat” mode on the air conditioner gives many advantages in comparison with the usual electric heater. The device consumes less electricity than a traditional heater. It evenly and quickly heats the air in the room.

During the operation of the unit for cooling the room, he tolerates thermal energy from it to the street, and when heated at the house, everything happens the opposite, the device takes the heat of the outer air and gives it to the room. Significant saving of electricity in comparison with conventional heaters occurs due to the fact that the air conditioner consumes energy only for the operation of the compressor and the fan.

Important! The most effective inverter units with adjustable power. The device supports the specified temperature parameters in the room.

As an environment responsible for transporting thermal energy or cold, a refrigerant is used in the air conditioner. Cold and warmth exchange occurs in heat exchangers.

  • The absorption of thermal energy with a refrigerant occurs in the heat exchanger when it contacts street air;
  • Next, the compressor pumps the freon into the internal heat exchanger;
  • Here, thermal energy is transferred to the air masses in the room.

Most of these units have one drawback. they can work for heating only if the temperature of the street air is not lower.5 ° C. If you turn on the equipment at lower outdoor temperatures, then the lubricating oil will freeze, which leads to a breakdown of the equipment or its stop.

Heating mode on air conditioning in winter

Before turning on the air conditioner for heat, you need to find out the air temperature outside the window, because in the cold season there are some nuances in the work of the unit for heating. It is best to use this equipment for heating the room in the offseason, and not in severe cold.

The technical documentation for any air conditioner indicates at what minimum outdoor temperature it can be turned on for heating the room. If the air on the street is colder than the specified threshold, then you cannot run the unit. He can break.

When working in frost in the equipment, the following processes occur:

  • The power of the heat exchanger is reduced due to the formation of hoar.
  • The defrosting system of the external unit will work constantly. Because of this, ice is growing in the compressor, which destroys the fan blades.
  • The heat exchanger does not work well because Freon does not have time to completely evaporate. The refrigerant flows through the drainage tubes into the compressor, which contributes to the appearance.
  • As a result of failures in the work, the compressor unit overheating, then freezes with ice and fails.

Step.by.step instructions to include air conditioner in heat mode

Now we will figure out how to turn on hot air on the air conditioner? Even if the instructions are lost, you can do it simply and quickly, because the principle of inclusion in all units is the same.

Important! Make sure that the model of the installed air conditioner has a heating function.

Before you configure the equipment for the desired mode of operation, check the air temperature on the street. Many models cannot be turned on if the window is colder.5 ° C. Only inverter units that have a winter kit are designed to work in colder conditions. So, some models of air conditioners Samsung, Ballu and Haier work at.15 ° C. However, the work of equipment designed for the cold season will be less effective at low temperature. This will also lead to rapid wear of consumables.

On a note! With the help of one split system, you cannot heat the room in the cold season of the year. Radiator heating should also work in the house.

To launch the unit in heating mode, you need remote control panel.

Before turning on warm air on the air conditioning remote control, do the following:

  • Run the unit by clicking on the “ON/OFF” button.
  • To transfer the air conditioner to heat, they press Neat. Translated from English, this means “warmth”. There are no such button on some remote controls. Instead, there is a mode key. With its help, switch the mode of operation of the unit. There may be a button on the remote control not with the inscription, but with the icons of snowflakes, sun, drops or fans. If there is no “Mode” or “NEAT” key, nor the image of the Sun, then this model is not designed to work in the heating mode of the room.
  • After that, the desired button switch the mode, select “NEAT” or the image of the sun.
  • Keys with arrows or “”, “-” on the remote control set the desired temperature. It should be higher than the temperature in the room at the time of inclusion of the device.
  • After starting the unit, the fan begins to operate, and the air heats up to a given temperature for 10 minutes maximum.

Important! There are models of air conditioners on which they first set up heating parameters on the remote control, and then start the unit.

However, even if there are the necessary buttons on the remote control, this does not mean that the device is designed to work in heating mode. Just the remote controls are released for all models, so they even come to the kit to devices that can only cool the room.

On some control panels, the transition to the heating mode of the room occurs according to another scheme, so you need to read the instructions. Also note that a control panel is not always used to go to the desired regime. Any split system has an external panel that is hidden behind a protective screen. The buttons of this panel precisely duplicate the control keys. Such a panel is needed in case of loss of the remote control, its breakdown, or, if it is at a considerable distance from the internal block. Setting up equipment for heating using the control panel occurs in the same way as using the remote control.

How to turn on the air conditioner for heat from the remote control and without, instruction of split systems of different brands

As new technologies are used, air conditioners can not only cool the air, but also heat it, if necessary. This became possible thanks to the launch of the reverse process of evaporation and condensation of the refrigerant, relatively used in traditional split systems intended exclusively for cooling.

So, when moving from liquid to a gaseous state, the substance takes heat, and in the room it becomes cool. In the opposite case, energy is released, which allows you to use this property for heating.

This is what many manufacturers of climatic technology use in the creation of the Winter-Site split systems, thanks to which you can maintain a given comfortable temperature almost all year round, with the exception of severe frosts. And how to turn on the air conditioner for heat. in the material further.

Based on the features of climatic systems, you can turn on the air conditioner for heat at a temperature of at least. 5 ° C. However, now many manufacturers produce products that can significantly increase this threshold before.15 ° C and even.25 ° C. True, such air conditioners are equipped with additional systems, which significantly increases their cost.

A conventional air conditioning system is able to convert 1 kW of electric energy into 3 kW of thermal under normal operating conditions. To what temperatures is it advisable to use the device for heating, it will help to understand the correction factor (KC), which shows the ratio of consumption and the return of energy. Когда температура за окном опускается ниже 5 °С, то КПД значительно снижается, и Кк получается равен единицы (то есть — при энергопотреблении 1кВт производится 1кВт тепловой энергии). So, with.10 ° C The correction coefficient is already 0.9. Thus, it is not advisable to use the device from an economic point of view.

Also, at very low temperatures, a number of damage may occur, which will lead to a breakdown of the entire system. For example, the refrigerant will not have time to evaporate in an exchanger of heat, which in the cold is covered with hoarfrost and loses power. The condensate will flow into the compressor, since the drainage system will freeze, which is fraught with the possibility of a hydraulic jacket. Therefore, it is important to know at what temperatures the operation of the air conditioner is allowed.

conditioner, heat, ballu, olympio

Important! A special oil is used to lubricate parts in the compressor, which at low temperatures tends to harden, thereby blocking the operation of some components. Excessive friction of the elements ultimately leads to the failure of the compressor.

Inclusion of the heating mode

Given the above, the air conditioner is advisable to use the premises exclusively in the offseason. before the launch of central heating. And to set up the device for warm air, you need to set the necessary operating mode. First you should check whether the heating mode is provided for in a particular model, and to what temperatures it is possible. such information is indicated in the instructions.

On the air conditioning or on the control panel, warm air is indicated, as a rule, by the “sun” or the “Heat” value (heat). Next, a few simple manipulations should be done:

  • Turn on the air conditioner;
  • set the desired mode using the “Mode” function. most often it is enough to press this button several times to switch to the supply of hot air, but in some models the modes are already made separately, then you just need to press the corresponding symbol of the Sun or the word “Heat” ;
  • Using the signs “or”-“, set the desired temperature in the room.

On a note! If the “Mode” functions are not on the control panel, then you need to go into “Settings” and find the required mode there.

All of the above is relevant for models without a control panel. The necessary buttons must be carried out to the air conditioner case. With their help, you can also configure the operation of the device for heating.

What climatic technique allows heating in winter

To navigate which air conditioners can be put on heating, and to what ambient temperatures they allow operation, it is convenient to use the classification presented in the table below.

Minimum temperature indicators Brand and model of split systems
from.5 ° C to.9 ° C Whirlpool AMD 311; Ballu BSLI-07HN1/EE/EU; Electrolux Eacs/I-07HSL/N3; LG PM-09SP; Leberg LBS/LBU-LOK08; Saturn (Saturn) ST-18TLHR/BIO, etc.
from.10 ° C to.14 ° C Daikin FTXB20C/RXB20C; Samsung AR09MSPX; Cooperhunter Inverter CH-S09FTXG; Panasonic CS/CU-BE20TKE; General Climate GC/Gu-Eaf09HRN1 and.
-15 ° C to.20 ° C Midea MSMB-09HRFN1-Q ION; Gree Smart GWH09QB-K3DNB6G; LG UU-24W; KENTSU KSGBA21HZAN1/KSRBA21HZAN1/-20; Dantex RK-18UHM3N
less.20 ° C COOPERHUNTER SUPREME CH-S09FTXAM2S; MITSUBISHI Electric Puhz-SHW80VHA 71 m²; Electrolux Viking Eacs/I.2HVI/N3 and others.

As indicated above, it is best to include the climatic system for heating in the off.season with soft climate: in the early spring or late autumn, there are no more codes anymore. And in the case of budgetary models, heating is possible only at plus temperatures.

Important! It should be borne in mind that the manufacturer, indicating the minimum value of temperatures for heating, implies a critical level. In this mode, the technique will not be able to work for a long time, since excessive loads are fraught with the rapid failure of the system.

Therefore, there is no unequivocal answer to the question of whether the air conditioner can be included in the winter for heating, there is no. It all depends on the specific model and winter temperatures.

If there is no switch

After heating was set on the remote control or body of the air conditioner, warm air should blew within 3-5 minutes. Even if after 10 minutes of waiting, nothing happened, then for some reason heating does not occur. You should once again go into the modes and make the necessary actions, while you need to carefully ensure that the technique reacts to the given commands. after pressing there should be a sound or light signal. If the system does not respond, perhaps batteries sat on the control panel, or it has broken. Then it is necessary to replace the nutrition elements or the entire DPD.

How to set up air conditioning for heating?

After you have launched the heating function, you need to set the corresponding temperature. This is done using the buttons “or”-“on the remote control, or upward keys. We recommend setting a temperature from 24 to 28 degrees, depending on your preferences and humidity in the room.

If you performed all the actions above, but the air conditioner still does not turn on for heating, then perhaps there is simply no such function in it. You can check this in the instructions for the air conditioner. If the instructions say that such a function is still provided, then contact the service company that serves you, it is possible that you will need repairs.

When you can turn on the air conditioner for heating?

The answer seems obvious: when it gets colder, and the temperature in the room will cease to be comfortable without heating. However, there are temperature restrictions for this mode, see the instructions or read below. As a rule, the high efficiency of the work of non-inverter split systems for heat is observed before.5ºС, inverter models. before.15ºС, then efficiency falls, t.e. It is most advisable to use the air conditioning for heating precisely in the offseason.

  • Air conditioning supports heating mode;
  • The air temperature on the street does not contradict the specified working range indicated in the instructions for the air conditioner.

How to turn on the air conditioner on the remote control?

To enable the heating function on the air conditioning using the control panel, regardless of the model, you need to perform a few simple actions:

  • Take the remote control from your air conditioner and turn on the device in normal mode, t.e. Click the on / office button.
  • The remote control should have the “Mode” button. Click it and switch the modes until the “Sun” icon or the inscription “Heat” is displayed on the screen.
  • Press the “Heat” key (or icon “Sun”). This will put the split system into heating mode and heat the room to 30ºС.
  • If your remote control does not have the Mode button, look at the buttons with the icons “Snowflake”, “Fan”, “Drop”, “Sun”. Click “Sun”. If there is neither “Sun” nor “NEAT” on the remote control, but other modes are displayed, then your air conditioner does not support the heating function.
  • Pay attention to the buttons with the notes “” “-“. They allow you to configure the temperature from 1ºС and above. Using them, set the conditions comfortable for yourself (the set temperature should be higher than the one that currently exists in the room). Or use the keys “Up” and “down”.
  • Be sure to wait for about 5-10 minutes. Warm air will not go right away. First, the fan will turn on, then the air begins to heat up. But pay attention, the device must respond to your actions (squeak, blink, turn on / off).

You can, on the contrary, first configure the heating on the remote control and only then turn on the air conditioner (press the “ON” button). For some models, it is this order that is considered correct.

How to choose a heating mode

If the user is convinced that the split system supports heating, you can proceed directly to the choice of this mode.

As a rule, DPDs are performed with 5 main buttons (with extended functionality there can be more):

  • Turning on/off.
  • Air flow rate adjustment Temperature Task.
  • Management of the work of the blinds.
  • Switching modes.

How to switch the air conditioner to heating step by step:

Заливка свай ТИСЭ. Расширение пятки. Рубашки. Каркас из арматуры.

  • Connect a split system to a supply network. In this case, the internal unit of the system should appear light and sound indication of the inclusion.
  • On the control panel with a single press of the ON/OFF button, start the system, wait for the opening of the blinds and the appearance of the air flow from the fan.
  • Next, you need to find the switching button of the modes, usually it is indicated as “Mode”. You need to click on it several times until the heating icon appears on the display of the remote control. In different models, it can be the icon of the sun or the inscription “Heat” (heat). At this moment, the air conditioner can close the blinds, and the rotation of the fan stop.
  • During the air conditioning is reconfigured to another mode, you can choose a comfortable heating temperature. This parameter must be set using the temperature adjustment button.
  • Using the speed adjustment button, select the warm air speed comfortable for the user.
  • Using the cluster adjustment button, install a comfortable air flow direction.
  • Wait until the air conditioner switch to a new mode and starts heating.

Switching without a remote control

Some models support switching modes without a remote control.

To do this, it is necessary:

  • Include a split system in power. Make sure that the equipment has started.
  • On the front of the air conditioning, you need to find a hiding control elements of the plastic cover. As a rule, it is small and made in the shape of a rectangle.

In this way you can not configure the desired heating temperature. This will only allow you to choose heat mode. To configure temperature indicators, you have to use the remote control. If it is lost, or broken, in any case you have to order a new.

Switching air conditioner to heat

Air conditioners should be operated with clear compliance with the most necessary standards. this action will ensure the extension of the service life to maximum, and also eliminates the owners of climatic equipment from the need for expensive and frequent repair, which, as a rule, is carried out with the replacement of expensive parts like a compressor or control board.

To install the air conditioner for heat (heating), you need:

Option 1:

1) We look at the remote control, there the “Mode” button (in some remote controls it is hidden by a lid).

How to Change Split AC From Heating Mode to Cooling Mode/مكيف الهواء المنفصل من وضع حار الى بارد

2) Click on the “Mode” button, until there is the “Sun” icon on the scoreboard or the inscription “Heat”.

4) When changing the modes, hold the remote control towards the air conditioner so that it receives signals, how you configure and make sound a confirming signal.

It is also possible to produce all of the above settings on the remote control and then sending the remote control to the air conditioner click the “ON” button.

6) In heat mode, the fan of the internal unit does not turn on immediately!

Option 2:

1) We look at the remote control, no buttons “Mode”, but there is a button over which the characters are symbols: “snowflake”, “fan”, “droplet”, “sun”.

conditioner, heat, ballu, olympio

3) set the temperature above the room. (An example in a room 20 degrees. Put 25 or 27).

4) as well as in the 1st version, we turn on the air conditioner, it should be squeaks with a characteristic sound of everyone in different ways. When a wired console is silent, but on the air conditioner when turning on, light bulbs light up.

5) Let’s go drink tea, if you don’t want to just wait five minutes.

Кондиционер BALLU Olympio Edge BSO 09HN1. Настенная сплит система Ballu

Option 3:

You do not display on your remote control, not the “sun” icon, but other modes are displayed.

This suggests that your air conditioner is not able to bring heat to your home. It works for you only for the cold.

4 option:

You are sure that the air conditioner is heat-cold, and not just cold.

You have done all the operations said above.

Air conditioning is turned on, the heat mode is set, the temperature was raised above approximately 30C., Air conditioner squeaked or light bulbs on the inner block lit up.

The air conditioner does not give heat, and is already included for 30-60 minutes.

I’m sorry, but you need air conditioning repair.

Before installing the air conditioner, it is necessary to study the instructions in detail, which indicates how best to perform these actions, as well as how to include air conditioning for heat. Experts advise not to save on such responsible actions as installation, but to trust professionals. But with elementary functions you need to understand yourself.

Installation of the air conditioning system

Air conditioners should be operated with clear compliance with the most necessary standards. this action will ensure the extension of the service life to maximum, and also eliminates the owners of climatic equipment from the need for expensive and frequent repair, which, as a rule, is carried out with the replacement of expensive parts like a compressor or control board.

Before installing the air conditioner, it is necessary to study the instructions in detail, which indicates how best to perform these actions, as well as how to include air conditioning for heat. Experts advise not to save on such responsible actions as installation, but to trust professionals. But with elementary functions you need to understand yourself.

The installation of the system should be made in accordance with the generally accepted rules for using this apparatus. you need to provide the system with a light flow of air and its outflow.

Switching the air conditioner to heat is carried out using the air conditioning control panel (du or wall). The operating mode of the air conditioner for heat is usually indicated on the control panel of the icon with the image of the sun.In addition, for the operation of air conditioners before its use, it is necessary to conclude with the company, which is its supplier, a special agreement regarding service of this system.

Before you start using the air conditioning, you need to find out all the details and features of its operation. how to turn on the air conditioner for heat or on the cold, how often you should ventilate it and whether it is possible to independently carry out preventive work? Everyone should know that regular maintenance of this unit will prevent the premature failure of the system. This, for example, often happens in the summer. at a time when service companies are fully loaded with orders and simply do not have any opportunity to quickly respond to the call to restore the functionality of specifically your system. So, if climatic equipment suddenly failed in a difficult period for repair, and you do not want to ditch it completely, you should not start repairing it yourself. You should turn off the air conditioner from the network and wait for a specialist who can carry out a real qualified repair, taking into account his knowledge in this area.

Optimum temperature

If you think that the air conditioner works like any heating device, you are mistaken. The split system does not heat heat, but transfers it from one environment to another. In the case of work for heating. from street to house or apartment.

The effectiveness of the air conditioner depends on the difference in the temperature in the room and outside. The larger it is, the worse the efficiency efficiency and its performance. About efficiency, COP and EER of air conditioning, we have made a separate article. You can read it here: // vteple.XYZ/KPD-KONDICONIERA-OHLAZHDENIE-OBOGREV/. Each air conditioner has a minimum temperature at which it can produce heat.

Inverter air conditioners can work for heating when on the street before.20.30 degrees (depending on the model). Ordinary. at temperature.5 5 ° C, no less. You can read more about the differences between them in the article “What is the difference between an inverter air conditioner from a regular non.inverter”

And then, at a minimum temperature, the air conditioner will not be able to warm up the air up to more than 18 21 degrees. Therefore, it is worth knowing at what temperature you can turn on the air conditioner in winter.

How to turn on air conditioning for heating without a remote control

Many models of split systems have an active control panel on the internal block. It can be sensory or ordinary, in the form of buttons. Sometimes it is hidden under a plastic lid.

If the buttons or control sensor are not visible, you need to open the front cover of the air conditioner. To do this, find in its lower part on the right and left of the recess or ledges under the fingers and pull it and up (see. a photo).

After the control panel is visible, it may not be on it/off button. To turn on the air conditioner without a remote control, you need to use a hidden button. It is located on the panel, to the right of the air filter. It can be marked as “on/off” or “auto”.

To turn it on, you need a regular handle. Depending on the diameter of the hole, reach the button either the writing or the back. In order to turn off the air conditioner. do the same procedure.

How to enable air conditioning for heating

The fertile time of heat, summer and vacations, stuffiness and heat retreated, has passed, and lost the power of a working air conditioner. It is time to enable the installed air conditioning for heating.

The experience of previous years suggests that with switching the split system to heating mode, for some reason, difficulties often arise and simply dead end situations. To some extent, you can complain about some scarcity of descriptions in the instructions for operation, but most often our person does not even look into this very instruction, and more than 30% of users do not even know where it lies.

In this article, we decided to describe in detail the sequence of actions when switching the air conditioner from cooling to heating.

House heating by air conditioning. step.by.step instructions

First of all, we include our split system in the 220V electrical network. On the remote control (DU) we find the power button (“Power” or “On/OFF) and click it. As a rule, the internal block is supplied with a quiet sound signal. After this signal, in most cases, blinds open and the fan of the internal unit is turned on. This is fine.

On some models of Ballu air conditioners. Carrier, MDV and others. This key is simply indicated by the letter “m”. If such buttons were not found, then we will storm the instruction manual and find where the air conditioner is switching on the remote control.

The split system has several operating modes, each of the modes is indicated on the display of the remote control with its icon:

  • Cooling. a snowball
  • Ventilation. a fan
  • Drawing. a drop
  • Heating. the sun
  • Automatic. autu or a.

Sometimes, instead of pictograms, inscriptions appear: Dry, Heat, Cool, Fan.

We click on the “Mode” button several times. until the display of the remote control will appear the icon of the sun:

For some manufacturers, it is difficult to distinguish the sun from a snowflake. be careful.

Further, make sure that your air conditioner is generally able to work for warming up, then the “sun” on the display will not see at all.

After you have chosen the “sun” button on the MODE on the remote control, the fan of the internal unit may stop rotating, and the blinds may be closed. The air conditioner seemed to be silent, thought. This is fine!

On the remote control with arrows set the temperature, preferably maximum, degrees 30. Please note that if the air temperature in the room is higher than you put it on the remote control, then the split system will not warm!

The air conditioner will continue to remain in a “thoughtful” state for up to 10 minutes, this time is required to restructure the processes of work, you just need to wait and it is better not to press anything else. As it turns out in practice, to wait out this interval of time becomes the biggest problem, it seems to the user that he did something not that the air conditioner is “stupid” or he is not working.

After 5-10 minutes, the air conditioner suddenly “wakes up” and begins to blow with warm air-cheers, you did everything right!

I would also like to pay attention to the next nuance: during all these manipulations with the air conditioning, do not forget to direct the remote control to the internal block of the split system. It often happens that the signal from the remote control simply does not reach the response in the internal block.

If after all this your air conditioner did not warm, then you should contact the service service of the climate company.

Please note that in winter you can operate a split system to certain negative temperatures from the outside, usually to.5-7 degrees.

Buttons on the air conditioner remote control

Any slide system has five main buttons:

  • Power button;
  • Switching button;
  • Double temperature adjustment button;
  • Button for adjusting the speed of rotation of the shaft;
  • Lyluzi direction adjustment button.

Read more about the value of these buttons can be spied in an article of the cooling settings.

But before taking the remote control, first we turn on the air conditioner into the network (like any electric device). Most often it’s just a fork that needs to be included in the outlet. The air conditioner power can also be through an automatic machine in an electric shield. In general, depending on the method of connecting the air conditioner, we turn on the machine or stick the fork into the outlet. In this case, you must hear the sound signal from the inner block. If the block does not react in any way, then read the article, which is why the air conditioner may not turn on. After a successful supply of power, we take the remote control and act further!

How to turn on the air conditioner for heat

I want to say right away that if you are mistaken somewhere, then nothing terrible will happen! You just need to wait and repeat everything again.

We are waiting for a few seconds, while the blinds open, and the fan of the inner unit will begin to rotate;

  • Then press the button to switch the mode so many times until we switch to the sun icon or the inscription “Heat” (which means “heat”).

After that, the air conditioner can stop the rotation of the fan or close the blinds (this will happen if the air conditioner has not been tuned to heat). What else will happen to the air conditioning, I will write a little lower, but now it does not matter. But at this moment we are already moving to the next setting (to the third point)!

  • While the air conditioner is “reconfigured” by the temperature adjustment buttons we set up degrees by 30. Let it be so for now, and in about 20 minutes already set up for yourself (I recommend 25-30 degrees).
  • The cluster adjustment button also put the most convenient position for you. Further, the most difficult thing is to wait until it turns out from the air conditioner with the long.awaited warmth. Then we set up the air conditioner comfortable for ourselves. Read more about the choice of temperature, as well as about the last two points, read the article on how to use the air conditioner correctly;

Now let’s get back to the second point. I want to explain in simple user so that you do not be scared, that a strange. There is nothing strange in his behavior! Just after switching the mode, the air conditioner’s algorithm changes, and it redirects the movement of the refrigerant (now you can not delve into this!). The temperature control of radiators and other processes that are not important for our article are. The most important thing for this article is only that you need to wait 10 minutes and do not press anything superfluous.

But there are several features that cannot be forgotten when turned on for heating:

  • When working on heat, the split fan can periodically stop (for heating the radiator). Don’t be scared! In most cases, this is its normal work;
  • If you do not know at what street temperatures you can use specifically your model, then at a negative street temperature I do not advise you to turn it on. Some air conditioners are defense for these cases, so they may not start. Read more on this issue, read the possibility of including the air conditioner in winter;
  • If the current temperature in the room is higher than you set up, then it will not “warm”;
  • When setting up, direct the remote control towards the air conditioner so that it receives a signal. Otherwise, it may turn out that the settings are changing on the remote control, and the air conditioner works in the same mode;

If in the cold period you are frozen, when you still did not have air conditioning, then with its acquisition you will immediately feel the difference. The heat that air conditioning provides you is cheaper than any heater. And it is also important that the temperature is very accurately maintained.

Finally, I’ll leave a link to another useful article about heating by air conditioning.

About the author

| Denial of responsibility | Contacts |RSS