How to remove the door of the Whirlpool refrigerator

How to outweigh the door of the Whirlpool refrigerator. How to remove the door at the refrigerator

In standard models of refrigerators, the door opens on the right side, but some manufacturers provide for design features that allow you to move the door leaf to the opposite side. This makes it possible to make the model ergonomic and comfortable for use. You can do such manipulations yourself, having an elementary set of tools.

  • Activity of the left, not the right hand. Consumer cause for outburst.
  • Choosing a model, we pay attention to technical features, dimensions, convenience in use, but we forget that the space is needed for the sash.
  • Rarving in the kitchen associated with the repair or installation of the sink, washing machine.
  • We remove the plugs from the bolts with a screwdriver, disconnect the mount. So that the lower loop does not deform, after disconnecting its fastening, it should be held.
  • Before removing the door, fix it with tape. Thanks to this simple procedure, the door will not open and will not fall at the height of the process.
  • On the middle bracket, a rotation axis mechanism is installed. Carefully get it.
  • Remove the bolts on the middle bracket. Having removed it, disconnect the door from below.
  • Remove the last bracket and install it mirror it on the opposite side, into the available holes. If there are bolts-bells, install them for a vacant place.
  • Next, change the pens. They are attached with screws. Often the fastener mechanism is hidden by a plug. Carefully pry it with a sharp object or miniature screwdriver. Be extremely careful, because the handles are made of plastic, using excessive strength when screwing. You can deform the material.
  • Move mirror to the other side of the stoppers (metal parts located from the ends that prevent strong opening of the doors).
  • Install in the reverse order all the details on the other hand. Fasten the brackets to the conscience, it is they who hold the entire weight of the doors with products.
  • If necessary, move the open door sensor.

For models with an electronic scoreboard, it is better to invite professionals, because you will have to move the display cable, which is difficult. If the doors are rearranged incorrectly, they will pass warm air, and the compressor will begin to work more intensively, as a result there will be a breakdown. To avoid this, after installing the refrigerator, tilt a little back. and the door will begin to close it denser. If the refrigerator at the warranty, remember, your intervention will lead to its cancellation.

Most modern refrigerators are constructively provided for the possibility of outweighing doors to the opposite side. As a rule, the advantage is included in warranty service. However, what to do if the warranty period has expired, and the redevelopment of the kitchen space implies that the refrigerator door should open in the other direction? In we published a price list of for the services of Rembettekh specialists, but, of course, you can try to outweigh the refrigerator door and yourself, armed with our advice.

How to rearrange the door on the refrigerator? Instructions

First of all, find out if the design of your refrigerator is a rearrangement of the door. This information is usually contained in the operating instructions. Do not remember where this document hidden? Then look for plastic plugs on the refrigerator body. a spare knot for attaching doors.

If it is, then the rearrangement of doors is possible. In addition, the instructions, as a rule, contain a detailed guide for a reorganization of the refrigerator doors to the other side specifically for your refrigerator model. Follow him if you managed to find it!

Whirlpool Refrigerator Replace Ice Dispenser Door Flap 2180353

You could not find a door overfing guide specifically for your refrigerator model? Then read on. Below we give a common sequence of actions to the outpoint of doors of a classic two.chamber refrigerator with electromechanical control. Out.bearing parts may differ for different brands and refrigerators models.

one. Prepare the necessary tools. You will need flat and cross.shaped screwdrivers, a wrench (its size depends on the brand and model of the refrigerator) and a painting tape.

Pull out the refrigerator out of the outlet. Before starting work, it is not superfluous to make sure that the refrigerator is disconnected from the network.

Fasten the door with masking tape. With the help of painting tape, attach the refrigerator door, which is dismantled first (in most models it is the upper door), to the body in several places

four. Unscrew the upper loop of the refrigerator. Dismate the plugs using the screwdriver, unscrew the bolts (using a key or screwdriver) and remove the upper mount. In some models of refrigerators, to get to the bolts of the upper loop, it may be necessary to remove the top panel (refrigerator cover).

Remove the upper door. Remove the masking tape, holding the door to avoid deformation of the loop. Then, carefully lift the door up, remove it from the lower pin of the middle loop and set aside to the side.

Rearrange the plugs of the top fastening of the door to the other side. Armed with a screwdriver, dismantle the plugs on the opposite side of the body and rearrange them in the liberated nests.

Dismantle the middle loop of the refrigerator door. To do this, first fix the lower door of the refrigerator with a painting tape to the refrigerator body. Then, remove the gasket from the pin and with the help of a wrench (or screwdriver) unscrew the middle loop.

eight. Remove the lower door. Remove the painting tape, carefully lift the door, remove it from the lower pin and also set aside aside.

Rearrange the plugs of the middle loop. Using a screwdriver, free the nest for attaching the middle loop on the opposite side of the refrigerator body. Rearrange the plugs in the free holes after removing the door.

ten. Dismate the lower mount of the refrigerator door. Pull the pin and use the screwdriver disassemble the lower door mount (in some models of refrigerators, a wrench may require a wrench).

eleven. Install the lower door mount to the other side. Remove plugs and rearrange them on the opposite side. Then, install the lower loop on the other side in the mirror projection and fix the pin on it.

Removing the door

It is necessary to remove products from the camera, turn off the device, and let it thaw. This is required to straighten a rubber seal so that it gains a normal shape, which is needed to regulate the door in a new position. In Indesit, the mount is provided with a rotary loop with some variations of the location.

How to outweigh the door of the Indesit refrigerator so as not to damage the technique? Electric screwdriver is used to eliminate. Removing decorative plugs is carried out with a knife or using a flat screwdriver. The bolts’ hats should have holes under the cross.shaped screwdriver. In their absence, you should choose a wrench with the necessary parameters.

First you need to take a false panel to have access to the wires of the wires, which serve as the door display with automation. It is necessary to loosen the tourniquet so as not to damage the wires with the door removal. It is important to disconnect the panel with the display.

Then the handle is removed and the lower fastening of the door is weakened, and then the upper. You need to disconnect the lower canopy and free the lower loop. To remove the upper canopy, you need to raise it up. The product must be put in a safe place, after which it is necessary to select a section of fastening the loops on the other side. Holes are closed with decorative plugs or plates. Special details are often required, it all depends on which refrigerator Indesit. Doors overpanization should be performed on the basis of instructions.

Tips and lifaces

The assembly can be complicated by the absence of fasteners for fasteners on the opposite part of the unit. In such a situation, it is necessary to drill them yourself. Such a procedure should not be done alone, if you make a mistake at least a millimeter, the door will be dung and cross.

  • Before starting work, de.energize the refrigerator.
  • Make products placed on the regiments of the inside of the door.
  • Carry all the manipulations carefully, trying to maintain the smoothness of glossy surfaces, the absence of dents on the door.
  • In order not to forget the procedure, write them down on the video.
  • Fold the removed bolts in a specially prepared container or tray.

Tips and lifaces

The assembly can be complicated by the absence of fasteners for fasteners on the opposite part of the unit. In such a situation, it is necessary to drill them yourself. Such a procedure should not be done alone, if you make a mistake at least a millimeter, the door will be dung and cross.

  • Before starting work, de.energize the refrigerator.
  • Make products placed on the regiments of the inside of the door.
  • Carry all the manipulations carefully, trying to maintain the smoothness of glossy surfaces, the absence of dents on the door.
  • In order not to forget the procedure, write them down on the video.
  • Fold the removed bolts in a specially prepared container or tray.

We outweigh the doors of the refrigerator. video

Almost all models of refrigerators have right.sided doors, but when there is a need to change their position, we wonder if this work can be done on your own?

Causes of curling doors

There are several reasons that are the basis for outweighing the refrigerator doors:

  • Layout of the room (kitchen), which prevents the right.sided opening of the door.
  • Lost the door of the door to the body.
  • The desire of a person with features (left.handed) to make for himself a more comfortable use of the refrigerator.

I must say that in some cases, the outbringing of the door may be provided for by warranty maintenance. At the same time, the owner of the household appliance has the opportunity to call the master at home once during the warranty period to perform this work. If the warranty period has expired, and the need for outweight remains, you can perform this procedure yourself, having previously studied all the stages of its implementation.

What to take into account when outweighing the refrigerator door?

Performing the procedure for outweighing doors in a two.chamber refrigerator is simplicity, as it is performed alternately. First, the door on the refrigerator is outweighed, and then on the freezer.

This process is complicated if the doors to the refrigerator with one chamber are launched, since in addition to the main door of the refrigerator, there is a need to replace the inner door of the freezer.

If the cause of outweighing the refrigerator door is its incomplete fit, then the reason should be found out. If the situation arose due to a dilapidated or dried elastic band, then it is enough to replace it.

When deformation of the door or weakening of the mounts, you can outweigh it or put it in order fastening.

Refrigerator door

If the situation requires outweighing the doors, it is necessary to stock up on with a knife, with worships and a cross blade, then you need to carefully study the instructions with a step.by.step description of the process and you can start the case.

Stages of execution of outweighing the refrigerator door

  • Before proceeding to the technical part of the solution of this problem, it is necessary to clarify the possibility of outweighing precisely on your refrigerator model. Modern manufacturers of refrigerated equipment in most cases provide for the situation with the outburst of the door and for this they make additional holes on the unit, closed on top with plugs. If necessary, they are easily removed with a knife or screwdriver.
  • The second stage provides for the removal of fasteners located on the refrigerator case. The twisting of the bolts must be carried out by holding the door, which then must be carefully laid on the floor or lean against the wall.
  • At this stage, it is necessary to remove the rotary loops from the door to close the holes with a plug. When rearranging loops, you must try not to change small parts in order not to break the design and operation of the loops.
  • Screwing the door to the body should start with the upper loop to avoid damage. After attaching the loops, it is necessary to adjust them.
  • When the door is rearranged to the other side, it is necessary to fasten the handle.With the improper rearrangement of the door, its tightness can be disturbed, as a result of which warm air will enter the chamber, which can lead to a breakdown of the unit.

To ensure a tight closure of the door when installing the refrigerator, you need to adjust its position with a light slope back. For this, adjustable supports are intended.

How To: Whirlpool/KitchenAid/Maytag Freezer Door Hinge Closure Cam WP2223751

Remember that if the refrigerator at the time of curling of the doors is under warranty, then the independent execution of this process will automatically deprive you of service provided for by the warranty period.

If you do not have full confidence in your abilities, and the refrigerator unit has features that you are not familiar with, then it is better to attract professionals to the performance of this work.

In some situations, you may need to outweigh the refrigerator door. In many models of refrigerators, it is impossible to do this, which is better to know in advance. The whole process of work is easy to do on your own, you just have to figure out if it is possible and how to outweigh the refrigerator door.

Installation of a refrigerator door on the opposite side of the case is required for the following reasons:

  • Interior change in the kitchen. In the place that takes the refrigerator in the new layout, there is no way to freely open the door.
  • The door closes loosely. In such a situation, it is necessary to rearrange the door faster, because through the gap between it and the body, warm air enters the refrigerated chamber. Because of this, the temperature inside rises, and the compressor has to work with a double load to compensate for the temperature difference. With such processing, the equipment will quickly fail. Sometimes it is not necessary to rearrange the door, it is enough to check the sealing gum.
  • If it is too worn out, polluted or deformed, then first you need to change it.
  • You are left.handed. Lenshm is more comfortable open the door to the right.

Acquaintance with the instructions

Before work, you need to familiarize yourself with the instructions that are included in the equipment for the equipment. There is usually a description of the stages of how to outweigh the door when buying the door is on the right side, and therefore tips for outcasting to the left are presented.

You should examine the device, find plugs, rotary loops. Special mounts should be located on the case. You need to start work only after the principle of work becomes clear.

What is needed?

It will be possible to outweigh the door of the refrigerator “Indesit” with:

It is necessary to remove products from the camera, turn off the device, and let it thaw. This is required to straighten a rubber seal so that it gains a normal shape, which is needed to regulate the door in a new position. In Indesit, the mount is provided with a rotary loop with some variations of the location.

How to outweigh the door of the Indesit refrigerator so as not to damage the technique? Electric screwdriver is used to eliminate. Removing decorative plugs is carried out with a knife or using a flat screwdriver. The bolts’ hats should have holes under the cross.shaped screwdriver. In their absence, you should choose with the necessary parameters.

First you need to take a false panel to have access to the wires of the wires, which serve as the door display with automation. It is necessary to loosen the tourniquet so as not to damage the wires with the door removal. It is important to disconnect the panel with the display.

Then the handle is removed and the lower door mount is weakened, and then. upper. You need to disconnect the lower canopy and free the lower loop. To remove the upper canopy, you need to raise it up. The product must be put in a safe place, after which it is necessary to select a section of fastening the loops on the other side. Holes are closed with decorative plugs or plates. Special details are often required, it all depends on which refrigerator Indesit. Doors overpanization should be performed on the basis of instructions.

What is needed?

It will be possible to outweigh the door of the refrigerator “Indesit” with:

It is necessary to remove products from the camera, turn off the device, and let it thaw. This is required to straighten a rubber seal so that it gains a normal shape, which is needed to regulate the door in a new position. In Indesit, the mount is provided with a rotary loop with some variations of the location.

How to outweigh the door of the Indesit refrigerator so as not to damage the technique? Electric screwdriver is used to eliminate. Removing decorative plugs is carried out with a knife or using a flat screwdriver. The bolts’ hats should have holes under the cross.shaped screwdriver. In their absence, you should choose with the necessary parameters.

First you need to take a false panel to have access to the wires of the wires, which serve as the door display with automation. It is necessary to loosen the tourniquet so as not to damage the wires with the door removal. It is important to disconnect the panel with the display.

Then the handle is removed and the lower door mount is weakened, and then. upper. You need to disconnect the lower canopy and free the lower loop. To remove the upper canopy, you need to raise it up. The product must be put in a safe place, after which it is necessary to select a section of fastening the loops on the other side. Holes are closed with decorative plugs or plates. Special details are often required, it all depends on which refrigerator Indesit. Doors overpanization should be performed on the basis of instructions.

Installation of the door on the opposite side

It is necessary to install the loops before outplay the door of the refrigerator “indesit”. The instruction includes the necessary rules to perform quality work. First, plugs are removed, and the canopies are attached to the holes. Do not immediately tighten the bolts tightly, because it may be necessary to adjust the position of the design.

If there is a closing sensor, during operation it must also be outweighed, and for this you need to take care of installing the mounts. When it is located in the center, the rearrangement is not required. There may not be a sensor, since in some devices it is inside the unit, under the lining. This also applies to the bulb circuit breaker: it is often attached inside, which is why the rearrangement is not required.

The canopies should have guide pins, so installing them in a new place will be very simple. But it happens differently. The pins are located on the door, which determines the sequence of actions. Awnings can be adjusted in height. First you need to install the lower hole, and then the upper. They are fixed with bolts.

You need to adjust the door by checking the high.quality fit of the seal. How to outweigh the doors of the Indesit refrigerator, so that everything is done firmly? The level is suitable for this, but you can compare everything visually. It is necessary to measure all parameters and adjust the shortcomings. When the door is redesigned, the refrigerator must be tilted a little back. After opening the door, the adjustment will be able to perform faster.

How to reduce doors on your own

We will describe the general stages of repair for two.chamber units. The process is simple, the main thing. act consistently:

  • Disconnect the equipment from the network by stretching the fork from the outlet.
  • Take the painting tape and fix the door to them from the side so that it does not fall during the dismantling.
  • Remove the plugs from the mounting holes with a decoction or knife.
  • Unscrew the bolts of the upper loop, dismantle the fasteners. If the loop does not succeed, you will have to remove the top panel (it happens from the manufacturers of the “turquois”).
  • So that the fastenings do not deform, hold the door from below. Unscrew the lower mount bolts in parallel. In some models, you can dismantle by just raising the door up.
  • If there were no spare parts in the kit, use those on the other side. Remove the plugs from the upper part and put in the released holes. Place the upper loop the opposite, expand mirror.
  • Go to the second part. Lower. Fix it with masking tape, as in the first case.
  • Remove the seal from the pin and unscrew the loop mounting with an indent.
  • Up the tape and remove the door from the seat, lifting up.
  • Prepare the mounting holes on the other side, freeing them from plugs. Install the latter in the vacant channels.
  • Change the handles if necessary, pushing them with a screwdriver or a sharp object.
  • Make a rearrangement of the lower mount and pin on one side to the other.
  • Tools rearrange the fasteners on the door on one side to the other.
  • Use the assembly in the reverse order, only on the other hand.

It remains to check the density of fit to the body. If the gaps or cracks are visible, you will need to adjust the refrigerator door. A thin sheet of paper (tracing paper) will help to conduct a test more accurately. Put the sheet between the body and the seal, close the door tightly. Then pull the sheet: if it easily fell, the fit of loose. If you fail to pull it out, everything is in order.

For refrigerators with a display

If you have Atlant, Samsung, Stinol, Bosch, Hotpone Ariston with the display, then the rearrangement is performed a little different:

  • Remove the upper panel of the case, twisting the fasteners.
  • Disconnect the wiring from the inside of the case.
  • As soon as you remove the upper part, disconnect the lid with wires with a screwdriver.
  • Remove the wires from the lid and rearrange the fastener on the opposite side. There, also throw a train.
  • As soon as the door is installed, the connection in the reverse order. Do not forget to install the top panel.

In HotPoint Ariston models, spare parts are not included in the kit, so you will have to rearrange those that were in mirror reflection.

In some refrigerators, “Ariston” and “Bosch” can be closing sensor. If you quickly close the camera, hear a sound signal. It is easy to rearrange the sensor: take it out of the seat and install it on the opposite side.

To perform such work in the two.chamber refrigerator “Atlant”, instead of a screwdriver, you will need a hexagon

As you can see, there are features everywhere, so it is advisable to immediately study the instructions. You can carry out repairs yourself if you adhere to our recommendations.

On all refrigerators, you can outweigh the door or not

Before outplaying the refrigerator door, you need to make sure that the manufacturer of the equipment provided for this possibility. If there are no technological holes for the alternative location of the loops. The sash will have to be left in the starting position or, in extreme cases, contact the workshop. You should not try to make holes on your own, the risk of damaging the device is too high.

Many household appliances include services for moving the refrigerator door to the warranty package. In this case, you need to contact the service center and ask the master to produce the necessary manipulations.

If the need for reinstalling the door arose after the expiration of the warranty period, it is allowed to do this without involving a specialist.

What tools are needed to outweigh the door to the other side

For redrawing the door, you need to prepare a set of tools:

  • Spanners. Their type depends on the refrigerator model. In most cases, the end and lacture keys are used.
  • Sprinkles. You may need a flat or cross.shaped tool.
  • Maslar tape. It is necessary to fix the sash and prevent it from falling during dismantling.
  • Spatula or knife to put plugs.

In addition, you can use spare loops, nuts and bolts that come with household appliances.

Transfer of loops to the other side of the refrigerator

To transfer the loops to the opposite side, first disconnect the plugs located there and install them in the holes released on previous steps (in which the bushes and rods were previously stood).

You need to act as if “backwards”, from the last step. Removing the plugs on the opposite side, start from below. Insert the lower loop into the lower nests, attach the rod. Then do the same actions with the remaining loops. the middle and upper.

Removing and installing handles on the door of the holder

If the design provides for the presence of handles, they also need to be rearranged to the other side. There should be plugs under the handles on the doors, they must be carefully pulled out using a screwdriver or knife. Thus, the holes for the bolts will be free, door handles can be attached to these places.

Unscrew the handles with a screwdriver, put the plugs on these places. Attach the handles on the other side.

What should not be done when removing dents on the refrigerator

Often, the metal at the point of the blow itself returns to the previous form, as it is in suspense. But if after 5 minutes this does not happen, you need to take appropriate measures.

Experts do not advise repairing with a simple hammer, try to straighten them the edges.

This will lead to the contrary to the fact that the dent will become larger and the paint will begin to fall off. No need to disassemble the door of the refrigeration unit, as the tightness will decrease.

If it is decided to align the surface with a putty and primer, it should be borne in mind that in any case it is impossible to achieve a complete similarity of the color of the processed place and the main shade of the refrigerator itself.

remove, door, whirlpool, refrigerator

The refrigerator will not work worse from the presence of a dent, so you should not accept such actions that will only aggravate existing defects. It must be borne in mind that today thin metal is used in the production of modern models. which is very easy to damage.

Thanks to the listed methods, it is possible to get rid of minor dents on the refrigerator at home and return the original appearance of stainless steel household appliances and other types of metal. Correction of more voluminous and deep dents should be entrusted to professionals.

Top refrigerators with a high rating

Scandilux r 091 w

the volume of the refrigerator. 78 l;

the volume of the freezer. 10 l;

compressors. 1;

cameras. 1;

doors. 1;

shelves in the refrigerator. 2;

Boxes in the refrigerator. 1;

Dimensions (shgv). 5254.4088 cm.

Olto RF-140C White

the volume of the refrigerator. 98 l;

the volume of the freezer. 40 l;

energy consumption. a;

compressors. 1;

cameras. 2;

doors. 2;

Taking off Whirlpool Side by Side Refrigerator Doors

Shelves in the refrigerator. 1;

Boxes in the refrigerator. 1;

Dimensions (shgv). 42.4044.50101.80 cm.

Indesit ITR 5180 S

the volume of the refrigerator. 220 l;

the volume of the freezer. 78 l;

compressors. 1;

cameras. 2;

How to remove the Freezer Door on a Whirlpool French Door Refrigerator

doors. 2;

Shelves in the refrigerator. 4;

Boxes in the refrigerator. 1;

Boxes/shelves in the freezer. 3;

Dimensions (shgv). 6064185 cm.

Weissgauff WRK 185 XNF

the volume of the refrigerator. 210 l;

the volume of the freezer. 76 l;

compressors. 1;

cameras. 2;

doors. 2;

shelves in the refrigerator. 2;

Boxes in the refrigerator. 1;

Boxes/shelves in the freezer. 3;

Dimensions (shgv). 6060185.80 cm.

Weissgauff wsbs 500 NFX Inverter

the volume of the refrigerator. 291 l;

remove, door, whirlpool, refrigerator

the volume of the freezer. 145 l;

compressors. 1;

cameras. 2;

doors. 2;

Shelves in the refrigerator. 4;

Boxes in the refrigerator. 2;

Boxes/shelves in the freezer. 6;

Dimensions (shgv). 90.5059177 cm.

About the author

| Denial of responsibility | Contacts |RSS