How to remove the fan from the deepcool cooler

Remove the cooler from the processor. The types of fan mounts and their features

If you discard possible the possible nuances, which will be discussed further, then the procedure does not seem so complicated. It should only be remembered that all actions should be done carefully. The main rule of disassembly is always: “Do not try to make efforts, especially if the” iron “resists it”. Following this rule will avoid unnecessary mechanical damage. To remove the cooler from the processor, you need:

Important! It will not be superfluous to let the computer stand 10 minutes before further disassembly. This is associated immediately with two factors: heating and residual charge in the capacitors. The first is just unpleasant. The second can cause tangible harm to the user and even components, with poor insulation of the power supply.

Twist the bolts on the body. For convenience in understanding, they are shown in the image. It should be borne in mind that you need to twist the right cover (if you look at the back, respectively, the left one. If you look at the system unit in front). The opposite is recorded stronger (often even soldered to the body).

Note! In general, completely disconnecting the wires and remove the RAM to remove the cooler from the processor, but for the first 10-15 removes this is necessarily. So that the hands are used to the operation and could not harm the surrounding components.

• Remove the cooling fan itself with the radiator from the processor. Almost always they are delivered and removed together too.

The procedure for removing cooler from AMD or Intel processors depends on the method of its implementation and may require both minimal efforts and huge physical costs. We will consider each of the cases separately.

Kuler fastening

The mount determines which algorithm of further actions should be applied. The cooling fan can be attached in the following ways:

Therefore, we will consider each type separately with the mention of the necessary tools.

Stils are considered a common option for cooers on the socket of 775 (Intel), although they are also found in other specifications. Budget fans are attached to latches. These latches are the main vulnerable place for such cooling systems.

To remove the cooler from the processor on the latches, you will need to turn counterclockwise the 4th mechanism (you need to make a turn on ¼ circle). Getting the iron part to pull the cooler.

If the latches are broken off (they are very tender and an effort to open borders with an effort for fault), it is better to contact the service center. Without proper experience, it is almost impossible to remove or install a cooler with a damaged latch.

To remove such a cooling system, you will need a screwdriver (cross or corresponding to the type of screw). Either an alternative tool like thin flat rods to unscrew the screw. By showing prudence and caution, you can cope with a knife, risking less than when opening latches with bare hands.

4 bolts are removed (they are not removed from the fan housing), after which the released element can be safely removed.

The mounting method is characterized by AMD processors and their cooling systems. The design looks as follows and has a lever:

This lever will need to be turned to free the cooling system, after which it can be pulled out.

Combined method

Combined mounting systems are found in the so.Called brand computers, where the latch is combined with bolts (less often everything is found at once). The cooling system is made as simple as possible and is less susceptible to damage during disassembly.

The disassembly algorithm repeats the actions for each of the corresponding types. The order is respected: first screws, then latches.

Liquid cooling systems are removed much more complicated. Over, for each model, the procedure is unique, therefore it is not possible to describe the overall procedure.

Adviсe

If you read the article to the end and you have doubts about the need for this procedure, perhaps they are justified. Washing and bulkheads are worthy of only good expensive cooler. Sometimes it is better to buy a new fan if it is cheaper than your time.

What can not be lubricated?

Do not use animal or plant oil: olive, sunflower, hemp, etc. It freezes and accumulates dirt, which leads to a fan breakdown.

It is also undesirable to use graphite lubrication. These are an abrasive, the particles of which will cause friction during operation and lead to washing the bronze clip of the sliding bearing and the fan. Also, graphite can conduct electricity and a short circuit will occur.

How to clean the PC fan

Part of the blades can be easily washed with water. Both blades and the center, you can easily clean by applying an old toothbrush. Try to carefully clean the axis of the old lubricant, which can significantly slow down the fan.

Sometimes also a magnet, located in the middle, collects a large number of different metal chips (this is especially true for fans in power sources, which often capture all the dirt from the environment). Cleaning the second part of the fan is reduced to the main cleaning on both sides of the hole in which the axis is supplied. This can be done using a fabric corner or cosmetic stick.Before cleaning holes, make sure there are no gaskets (these more expensive windmills are almost always). If they are, first pull them out and clean them.

If you have access to compressed air, this will not hurt to blow the fan. When everything is cleaned, we can go to grease. Here I can recommend petroleum oil, it is enough to provide good grease.

And all. Now you need to put the cork (it is much easier to put on than to remove it), press the rubber plug and stick the sticker. When the pin is well installed, the sticker can be good. However, if the axis sits freely, you must hold it something so that it does not fall out. I attach a piece of the Power Tape tape (also widely known as “Gray Tape” or “Macgyverka”;).Of course, you can seal something anything.I hope that this brief guide will reduce you to reduce the noise created by the computer

Change the processor: how to remove the cooler and install the processor.

A powerful processor is comfort and convenience when using a computer. It so happens that when buying a computer or laptop, people incorrectly choose a CPU, which is slower than necessary to solve their problems. This usually happens due to the savings and hope for a further upgrade of the computer (when the money is), or just because of a lack of knowledge. But even if the top CPU was bought, then in a few years he manages to become obsolete morally, and the processor performance is no longer enough to solve the tasks assigned to it. In this case, you can do UPGRADE computer: Replace the processor. In this article we will talk about, how to remove the cooler and replace the processor In a regular desktop computer (desktop system). Such a laptop Upgrade is quite complicated, and sometimes it is completely impossible. Even if your Notebook’s model allows such an upgrade, then the CPU replacement instructions for your model must be found on the network.

The processor replacement procedure is generally simple and unpretentious: 0. Disconnect power from the system unit! Disconnect all wires from him! One. Open a system unit; 2. Remove the cooler with CPU; 3. Open Socket with a processor; 4. Replace the processor; 5. Close Socket; 5. Apply a layer of thermal paste to a new processor; 6. Install the cooler.

How to open a system unit: this is usually done by unscrewing several screws around the perimeter of the rear panel of the system. Modern housing models and more often they use screws with a rolled head, for the twisting of which it is not even required to be a screwdriver. Do not rush to twist all the screws! Most likely, it is possible to remove only one side cover, behind which there is full access to all components of the system unit. In order to remove the sidewall (or the entire casing), it is necessary to shift them slightly in the direction from the front/front panel to the rear wall (literally 1 centimeter). After which the removed element is easily separated from the chassis. So, they dealt with the body Put it on the side to make it more convenient to work.

How to remove the cooler: there are many variations on this step. It all depends on the installed model of the cooler. Typically, the dismantling method should become clear after a visual review. We recommend that these operations are carried out in a fairly free space where you can turn the entire computer of the computer into a more convenient position without interference.

If the system is equipped Intel CPU and the most popular standard solution for its cooling, then removing the cooler is quite simple. It is necessary to turn 4 plastic pin with a flat head in the direction indicated by the arrow on their “hats”, and pull it slightly upward. After these manipulations, each of the pins can Remove the cooler, also carefully pulling him up.

If your system unit is equipped AMD CPU and a boxing cooler, then find one on it or A couple of “levers”, which must be “threw” in the other direction. After this, the bracket, pressing the radiator, will weaken and allow to “throw off” its ends from the hooks on the socket (nest for CPU), after which you can remove the cooler from the processor.

In the case when a non.Standard solution is established for cooling CPU, you will most likely need a screwdriver, which needs to turn out several screws (usually four) that hold the radiator on the processor. It is possible to have an additional frame on the back of the “motherboard” to prevent bending of the last. Examples of such “non.Standard” fasteners can be seen in the photo above. In the most difficult cases, it may be necessary to remove the video card or even the entire motherboard from the case, but this is quite rare. Such systems are usually used by enthusiasts who like to “indulge” with extreme overclocking of processors and video cards. So, if you have never removed the cooler and do not belong to it’s, then 90% your system is equipped with a typical CPU cooling solution, and removal problems should not arise.

Additionally, we pay attention only to the fact that a thermal paste, which could already be between the radiator and the processor dry, As a result, the CPU and the radiator can stick a little. In this case, after unscrewing (unfolding) the cooler, it is necessary to apply some effort when it is removed. Additionally, you can try a bit to turn the radiator relative to the processor. This is easier to peel off the cooler. If the thermointease has not dried, then it is very getting dirty. Consider this moment and have a rag or hand for hand at hand.

How to remove the processor: it is necessary to free it from the socket, by way Raising the lever, pressing or processor itself (Intel) or clutching its legs in holes with contacts (AMD). Be careful with the extracted CPU. You should not drop it. In the event of a CPU fall without legs, nothing terrible should happen on the soft floor. The processor should not break. If there are legs on the lower side of it. They may bend and you will have to straighten them. If you drop the processor on a tiled or granite floor, then a chip of a crystal substrate containing hundreds of the finest conductors is quite likely. In the latter case, the processor can be thrown away. It is no longer restored. Generally. Be careful!

The new powerful processor is installed in the socket exactly in the same orientation as the old. For Intel CPU, there is usually a pair of “depressions” on the CPU substrate ends and appropriate protrusions in the juice. AMD processors most often have a marked angle, which is indicated from above with a white triangle and have a bevel on the “figure” of the contacts of the lower side. After proper positioning CPU, insert it into the connector and squeeze it with the help of the existing lever.

After you replaced the processor, it is necessary to apply a thin layer of thermal paste (to the surface in contact with the radiator) and install the cooler. Keep in mind that powerful processors usually have significant heat generation and should be cooled by the corresponding cooler in order to avoid overheating and failure. Modern CPUs, of course, are equipped with temperature sensors and can reduce their energy consumption (and heating), but this is due to a decrease in speed But you replaced the processor by more powerful to increase speed! The final step do not forget to connect Cooler power to the corresponding connector on the motherboard (CPU_FAN), close the body of the system unit and wrap in the place of the screws unscrewed in the first step.

Instructions for installing and dismantling the AMD CPC cooler

This article provides instructions for the installation and dismantling of the CPU coolers, which are included in the set of a number of AMD processors.

This article consists of the following sections:

When assembling a PC of any system, it is important to properly install the CPU cooler in order to ensure efficient scattering of heat to maintain the operating temperature within the corresponding limits.

Before you start working with any components and sensitive electronic PC elements, such as CPU, it is necessary to take mandatory precautions, the examples of which are given later:

• If possible, work in rooms with carpet coating should be avoided, especially for cool and dry areas;
• Before working with the components of the system, it is necessary to remove the charge of static electricity by touching some grounded metal object, for example, to the metal body of the system;
• When working with any electronic devices, antistatic devices, such as bracelets should be used.

Additional information about working with central AMD processors cm. The article is: Processor Handling Guidance

This article provides instructions applicable primarily to the AMD Socket AM4 platform.

Installation of CPU cooler

Socket AM4 AMD central processors are equipped with two types of coolers. Different fasteners are used for fastening to the motherboard: fixing brackets and spring screws.

Installation of CPU cooler with fixing brackets:

• Make sure the CPU installation in the socket is correctly installed. Instructions for installing processors AMD Ryzen see. The video in the video: How to Install AMD Ryzen Processors.
• Information about thermal package: In the case of repeated installation of the CPU coolerator, the upper cover of the CPU and the lower plate of the CP cooler must be cleaned and completely removed the remaining the old thermal paste. This can be done using isopropyl alcohol and non.Permanent tissue.
• In the case of installation of the new CPU cooler, a thermal can already be applied to it. In this case, apply thermal grease to the CPU cover is not required. Go to the stage

Latch

Stils are considered a common option for cooers on the socket of 775 (Intel), although they are also found in other specifications. Budget fans are attached to latches. These latches are the main vulnerable place for such cooling systems.

To remove the cooler from the processor on the latches, you will need to turn counterclockwise the 4th mechanism (you need to make a turn on ¼ circle). Getting the iron part to pull the cooler.

If the latches are broken off (they are very tender and an effort to open borders with an effort for fault), it is better to contact the service center. Without proper experience, it is almost impossible to remove or install a cooler with a damaged latch.

Removal procedure

If you discard possible the possible nuances, which will be discussed further, then the procedure does not seem so complicated. It should only be remembered that all actions should be done carefully. The main rule of disassembly is always: “Do not try to make efforts, especially if the” iron “resists it”. Following this rule will avoid unnecessary mechanical damage. To remove the cooler from the processor, you need:

Important! It will not be superfluous to let the computer stand 10 minutes before further disassembly. This is associated immediately with two factors: heating and residual charge in the capacitors. The first is just unpleasant. The second can cause tangible harm to the user and even components, with poor insulation of the power supply.

Note! In general, completely disconnecting the wires and remove the RAM to remove the cooler from the processor, but for the first 10-15 removes this is necessarily. So that the hands are used to the operation and could not harm the surrounding components.

Remove the cooler from the processor

This article will tell you how to correctly and safely remove the cooler from the processor. Trying to tear off the fan that has grown to the CPU is a great chance to damage the “heart” of your computer. How to avoid this? I will try to describe the correct algorithm and possible situations, they drove.

One. The computer should be completely disconnected from the network before starting. This is understandable, another thing: is it worth waiting for complete cooling?

Let the radiator cool. Opinions diverge.

On the one hand, this is true: CPs can heat up to 90 degrees, burn your hands. But at high temperatures of thermal paste, which is located between the processor and the fan is more malleable; In other words, in a dry state, the process of removing the cooler can become a real problem. But this does not work for all types of thermal paste. With KPT-8 will not work: it is pastoral at any temperature.

I advise you to remove the fan when the radiator has not yet completely cooled down. When the hand is touching it, it will be warm, but not hot.

To do this, we pull the plug strictly vertically.[adsense]

Any loosening is unacceptable. Break a needle.

Remove the fan mount.

The type of fastener depends on the motherboard and each specific device. Complexes are used on some computers, on others-some latches. At first, this seems to be a problem, but in fact. Nothing beyond complicated.

If there are bolts, then they should unscrew them counterclockwise.

Above was the prelude, now we will perform the action itself. When everything is disconnected, pull out the cooler with the radiator. And then they will come. PROBLEMS.

With 90% probability of CPU in the literal sense of the word sticks to cooling. Because of thermal paste. Be extremely careful: loosen up and down, left to right, clockwise and t.P. Gradually increase strength and amplitude. Rush or immediately show excessive efforts is prohibited.

Do not be surprised and don’t be scared. If, along with cooling, you will pull the processor out of your native nest.

P.S. Turn on a computer without a fan is to kill the processor. With a guarantee and control shot. Do not do it this way. Also, do not be too lazy to change thermal grease before assembly, good luck!