Step by step instructions for removing the rubber band
Before proceeding, you must disconnect the device from the power grid and water supply. this will protect against electric shock and prevent flooding of the room with water.
To remove the rubber band from the drum of the washing machine, you need to follow the following algorithm:
- According to the instruction manual of the machine removes the top cover.
- A rag is placed under the appliance.
- The door is removed.
- Examine the system for fixing the seal on the front wall and the drum.
- Using a stack or spatula, carefully pry open the spring of the retaining clip on the front wall of the door and remove it so that a screwdriver can be inserted and the wire can be pulled out beyond the groove.
- Gently gradually slide the retaining clamp outward beyond the groove until it is completely clear of the throat circumference.
- In machines that have a removable front panel, it must be removed to provide free access to the drum.
- Inspect the attachment of the spring on the drum. it is usually located at the top.
- Similarly to the outer ring of the wire, the clamp securing the clutch to the drum is removed; in some models, it is possible to simply disconnect the spring and the wire.
- After loosening the clamp, it is led out beyond the edge of the seal.
- When the clamp is completely removed, separate the rubber from the outer wall of the machine and bring it inside. The clutch must remain attached only to the drum.
- If the front wall is not removable, then from the inside of the drum is picked up a seal and removed completely into the space between the drum and the body.
- The removed seal is removed from the outside.
Sealing the door seal in the washing machine. Instructions Photo
The modern housewife will not be able to imagine life without her main helper at home. the washing machine, so some unforeseen breakdown will be immediately eliminated with some repair actions.
Replacing the rubber on the washing machine: sequential instructions
A washing machine is a complex household appliance, the breakdown of which entails expensive repairs. But there are some failures, which you can fix yourself. One such malfunction is replacing the seal in the washing machine. In the article, using examples of models from several manufacturers, the sequence of work when replacing the part is described in detail, it is told what materials and tools are used. Recommendations for preventing damage to the rubber part are given.
Causes of breakage
There are not many reasons why the ring seal ceases to perform its duties. And the main share is manifested when the rules of use of household appliances are not followed.
The key ones can be called the following:
- Mechanical destruction by hard objects;
- Large vibration of the drum in the process of spinning;
- exposure to aggressive substances;
- if there is mold on the rubber;
- inadvertent loading of dirty items or removal of washed items;
- natural wear and tear.
Replace LG Front-Load Washer Door Boot Seal #MDS47123604
Object damage occurs when the machine is often used to remove dirt from rough items, such as sneakers, things with zippers, and so on. Negligent placement of metal objects (nails, coins, keys) and plastic items in the drum can also cause substantial damage to the rubber.
The drum of a washing machine can vibrate a lot if the machine is not installed correctly. This causes the O-ring seals on the load to suffer. The use of bleaching agents often and in high concentrations leads to rubber coarsening. And the loss of plasticity as we know, can cause defects quickly.
So do the alkalines and acids used to clean the machine. again, if used incorrectly.
For example, some users believe that the greater the concentration of the substance, the more effective the cleansing. But they also neglect the aggressive action on the components.
Molds are microscopic fungi that grow in colonies. Once settled on soft rubber, the fungus of these tiny creatures can grow to great depths. With an intense affection, stains that give off a bad stench can’t be removed in any way. In such a situation the only remedy is to replace the seal with a new one.
The washing machine is not long-lived. Even when handled with extreme care, the elements eventually grow. The seal is no exception.
It is constantly exposed to the rotating drum and laundry, temperature fluctuations, detergents. All these circumstances gradually make the rubber brittle and unbreakable.
How to replace the cuff on the washing machine LG?
Any automatic washing machine is a complex device, in which every detail is important and necessary. If one of the parts fails, the work of the entire unit is stopped. Every washing machine has a rubber cuff on the boot door, which can wear out over time.
Mold in Front Load Washer Gasket. How to remove & clean
Is it possible to replace this part by yourself, without resorting to professionals, and how to do it correctly. we will consider in this article.
Installing the new cuff
Before you fix a new door cuff, make sure it’s the exact same brand as your machine, otherwise the seal will not be strong as a result. Thoroughly wash the so-called “rim” hatch from accumulated dirt, lime and mold. To do this, just take any soapy solution.
It is not necessary to wash off the soap: by sliding it, you will have an easier time installing the new rubber, because the new part is likely to be tight and inelastic.
Check whether the mounting marks on the edge of the tank and the collar itself coincide, and pull the collar on the hatch. Hold the lower part with your fingers, tightening the upper part, then the other way around. The same soap solution will come in handy as a lubricant.
HOW TO REMOVE MOLD FROM YOUR WASHING MACHINE | FRONT LOAD GASKET MOLD REMOVAL
Then proceed in the same manner as when you remove the rubber. Reinstall the clamps, screw in the screws and check if the seal is properly “seated. After all, if the installation was poor quality, there may be leaks in the future.
To verify whether you managed to properly replace the sealing rubber, run the washing cycle on a short program, without putting things in the hatch. After completing the process, see if any water appeared in the area of the bottom of the cuff.
Signs and Causes of Malfunction
The main sign of a faulty cuff is water leakage both during washing and during rinsing and spinning. Scratches, cracks and holes appear in the rubber.
The hotter the water, the lower quality powder, the more of it is put into the washing machine, the sooner the sealing rubber will wear out.
The silicone seals are capable to work for about 10 years without any problems, especially when the washing machine is quite expensive. The manufacturer, which is a respected and trustworthy brand, does not skimp on the quality of materials and manufacturing processes of parts.
No matter how high the quality of the parts, they are subject to gradual wear and tear. The cuff cracks from frequent overheating when washing in boiling water, because of the use of special bleaching agents, either loaded separately or contained in expensive laundry detergent. Scale (and its remedy) that is washed off the boilers, excessive water hardness, as well as untimely cleaning of mold that forms on the seals also have their effect. The latter is the most dangerous: mold itself is quite adaptable to new conditions. Germming into any material, including rubber, can irreversibly damage it over time. In addition to mold, other types of fungus also pose a danger. Creating excrescences on the surface of the seal, they disturb the outer contour of the cuff.
When the door is closed, gaps are left, which cause the detergent solution and wastewater from washing to leak out. Because of this, the machine can engage the additional pumping of water by opening the fill valve, which reduces the concentration of detergent, reduces the quality of washing and leaves puddles on the floor near the washing machine.
Other signs are:
Cuff wear can be caused by bra clasps, hats with visors, shoes with excessively hard soles, metal zippers and buttons on clothing, rough work clothes, keys, coins, fasteners, and more.
There have been cases of a machine leaking water after accidentally washing an iPhone without taking it out of its The metal frame around the perimeter of this smartphone has done its dirty work, and it has torn the thinning cuff of the washing machine in several places.
Any electrical appliance, including washing machines, will soon break if handled carelessly. Not quite careful moving, such as when you move into a new apartment, can also damage it.
As for washing, it is acceptable to use special bags that are easily permeable to water and detergent, as well as to turn clothes inside out. The latter will protect the drum, cuff and hatch door from clasps, locks, buttons and plaques from which they cannot be released.
Torn and leaking cuff in the washing machine? Solve
Of course, the first is the detection by eye, t.е. Visually. Look carefully at the cuff itself, if you find a hole or puncture in the washing machine rubber, you have found the cause of the puddle of water on the floor, ie.е. The cuff broke.
The second is the nature of the leak. Т.е. Water may come from underneath the washer or leak from the hatch when washing or rinsing.
What and how you can clean the gum in an automatic washing machine
One day, when you load another batch of dirty laundry into the washing machine, you may smell an unpleasant, musty odor, and see dark, moldy spots on the o-ring. If the plaque is not much spread, then the machine will be easy to save, but in some cases you may need to change some elements, such as the drain hose, detergent tray and even the rubber gasket itself. To avoid this, the fouling should be periodically cleaned. Today we will look at how you can clean the limescale gum of an automatic washing machine.
