How to remove the lock with an oven Hansa

Hansa BHI 68314 instructions for use online. Page 21

Instructions for Hansa BHI 68314 induction hob contains pages in Russian.

You can download a pdf file of this instruction: Download PDF

Духова шафа Hansa BOEW64190014

If when you turn on the “Booster” function, the full power is too

is great, the heating power of the other field in the pair will be maximum

Two heating fields, set vertically, create a pair of.

lock, oven, hansa

The blocking function serves to avoid unintentional switching on

of the hob by the children, and its activation is possible after the unlocking.

The blocking can be activated only when the hob touch panel is on,

none of the heating fields is active (on the display will light up the digits “0” with

After switching the panel on with the sensor (1), simultaneously press the sensor (5)

lock, oven, hansa

the front left heating pad with the sensor (4), then press again

the sensor (5) of the front left heating field. All the displays now show

“L”, which means that the blocking function is on. If the fields are hot, the

The locking of the hob must be done within 10 seconds and cannot

Do not touch any other sensors than those mentioned above. Otherwise

In this case the hob will not be blocked by.

lock, oven, hansa

Unlock the stove for the duration of use

After switching on the hob with the sensor (1), the letter “L” will appear on all the displays. Then

simultaneously press front left heating field sensor (5) with

See also  Do I need an RCD for a hob

sensor (4) at the same time. The “L” letters will disappear and the numbers “0” will appear on the heating fields display.”

with the flashing button. It will then be possible to start the heating fields (as

described in the section “Setting the degree of heating power of the induction field”).

The hob will be locked until it is unlocked, even if the panel

will be on and off. Disconnecting the hob from the power supply will not

To activate the lock press and hold for 5 seconds the WATCH sensor. On the display for 5 seconds the inscription Loc. Signifying that it is not possible to change the function parameters. To deactivate the lock press the lock sensor again for a few seconds.

To turn on the Hansa gas oven, light a match, press the control knob as far as it will go, then turn it to the left to the selected temperature mark. Bring a burning match to the ignition hole, light the gas and hold the knob down for about 3-10 seconds. If the flame goes out, repeat the steps.

Usually electric ovens are equipped with a sensor. The gas oven, on the other hand, is equipped with a more simple regulation. On the control panel you need to find the lock button, usually indicated by a key symbol. Press this button, and then select the option. lock control, press it for a few seconds.

On the control panel you should find the lock button, usually indicated by a key. Press this button, and then select the option. control lock, press it for a few seconds. A buzzer should sound to indicate that unlocking was successful.

  • Switch on the appliance;
  • Set the required temperature;
  • let the oven heat up to the set temperature;
  • place a dish in the center;
  • Close the door and set the timer;
  • After the buzzer sounds, check the dish and, if necessary, turn the appliance back on.
See also  Split system with blowing ventilation daikin

To set the time: Press sensor 1 (MENU). The “Steam cooking pot” symbol must light up. After 7 seconds set the current time using the sensors 2 and 3 (arrows pointing left to right). Once the time setting is completed, the new data will be entered into the memory.

Instruction to use the electric oven:

  • Turn the appliance on and after setting the temperature, let it heat up.
  • After 10 minutes, open the door and place a dish inside, preferably in the center.
  • Close the oven. Set the timer.
  • After the beep, check if the food is ready. Turn the appliance off.

To set the time: Press touch 1 (MENU). The “steaming pan” symbol should light up. Set the actual time using the sensors 2 and 3 (arrows pointing left to right) After 7 sec. After you finish setting the time, the new data will be entered into the memory.

To harden the oven, turn it to the maximum temperature and let it operate and heat up empty for 1 to 3 hours. If the toxins and smells are not gone, flame the oven again.

Lo” on the display will indicate that the protection has been triggered. At the time when the lock is active, the induction hob will only work on and off, but it will not be possible to activate the heating in any zone.

Turning off the induction hob at the end of cooking is done by means of the control panel (“Turning off” item), if available. If the appliance is not equipped with a display, turn it off by pressing the “On/Off” button.

About the author

| Denial of responsibility | Contacts |RSS