How and what to fix/remove a chip on the kitchen countertop at home
Before you begin the restoration of kitchen furniture, you need to make measurements. It is important that the repaired areas do not exceed the original dimensions.
If you see the slightest signs of deformation, you should not hesitate. You can treat damaged areas with silicone. it will protect the material from moisture penetration. Waterproof acrylic sealants also have similar properties.
How to restore a plastic tabletop
To repair chips on the plastic countertop use a special glue composition. For example, a transparent glue “Moment Plastic, applied with a gun. It is convenient to glue splintered pieces of furniture. The disadvantage of glue is its high price.
Help. Cracks, gouges and scratches can be repaired with an ordinary instant adhesive.
Large chips and cracks can be repaired with Titanium Glue. Grind a loose piece of plastic into powder and mix with glue. Apply the resulting mixture to the damaged area.
Repair chipboard countertops
How and what to fix a chip on the worktop of chipboard? Before you start the repair, you need to prepare the coating. sand the area and then sand it down. To rub the surface, it is best to use felt.
To restore the Wood particle board tabletop will need:
Step by step instructions for repairing the coating:
- Turn on the hair dryer and heat the damaged area.
- Remove the peeling coating.
- Cover the damage with a layer of glue, leave it to dry for 25 minutes.
- Prepare a mixture of shavings and glue. Mix the ingredients and let stand for 10-15 minutes.
- Pour the prepared mixture into the damage and tamp it with a trowel.
- Tighten both parts of the crack, use the remaining glue to fill the void.
- Remove excess adhesive mixture.
- The table can be used after 24 hours.
Experienced craftsmen recommend using a press for greater density of the mixture. It can be made of two bars, the height of which does not exceed the height of the table. On the table top and bottom place planks and tighten with two screw clamps.
Help. To protect the repaired area from damage, cover it with sealant.
If the laminate countertop is loose, but the coating itself is not blown, you can treat the joints and corners with sealant or silicone.
Restoring wood
For the repair of tables manufacturers produce special compositions. hard waxes and furniture strokes.
Wax is for removing dents, chips and scratches. It also increases the moisture resistance of the coating and resistance to mechanical damage. Before using it, heat it with a lighter, then caulk the damage and leave it for three seconds. Remove residue with a box cutter and sandpaper.
Furniture touch will help get rid of minor scratches. Shake product before application, then apply 2-3 times. When the compound dries, remove the excess with a soft cloth.
Chip on fiberboard Fiberboard
Shallow scratches and burn stains can be removed with a sander. Use a fine abrasive wheel when working.
If you do not have the proper equipment, small damages can be sanded with medium and then fine sandpaper. Polish the treated area with a soft felt.
For restoring large cracks, you can use a small repair kit.
If no suitable shade of putty is available, it can be obtained by mixing two other similar colors.
- Trim the edges of the damaged area with a chisel.
- Retouch the cut with a felt tip pen.
- Mix the putty with the melting agent and putty it on the chip.
- Smooth the surface, remove any excess.
- Coat with varnish to fix the mixture.
Repair stone countertop
Only tables made of artificial stone can be repaired at home. Natural materials require the experience of a craftsman and special tools.
For care and restoration of the stone slab produce a special acrylic or glossy solution. Before it is applied, the surface is cleaned and degreased.
The easiest way to remove scratches on a table is to use a grinder. Grinding will help hide traces of long-term use of the coating. Then special products are applied to the countertop and polished.
How to fix a chipped glass cooktop
Ammonia alcohol Ammonia alcohol can also effectively clean stale dirt from the cooking surface. In a glass of water you need to dilute 1 teaspoon of alcohol and apply the resulting solution to the surface. Let the dirt soak for 10-15 minutes.
How and how to clean an electric stove burner?
- The stove should be heated up and turned off;
- During heating, all that is on the burner will be charred, it remains only to remove the loose particles with a dry cloth or sponge, when the device cools down.
The main reason for damage to the hob glass is the fall on it of heavy objects. a cast-iron frying pan or a massive cauldron. It often happens that the surface withstands multiple impacts, and then cracks appear on it for no apparent reason.
Happens when the stove has been improperly installed, and the powerful voltage applied to the technique destroys the cooktop. The surface begins to crack from the central part, after the defects diverge, having sharp corners. Pitting damage, such as a dropped knife. Tearing off cookware that is glued.
A chipped glass ceramic hob what to do?
and more housewives are buying glass-ceramic cooktops instead of the usual gas or electric stoves. A flat surface is easy to clean, but must be handled with care. Improper care of your cooktop can lead to gradual deterioration of the cooktop.
What’s wrong with your cooktop?
No matter how tidy the hostess is, the cooking process causes the stove’s surface to become dirty. White spots on the glass ceramic hob can form if a pan with a wet bottom is placed on it, if clean water is spilled. The liquid evaporates and the salts it contains remain on the mirror surface as a whitish lime deposit.
Most dangerous if sugar (syrup, caramel), plastic or foil gets on the hot plate. Molten particles solidify and stick to the glass ceramic cooktop, trying to remove them can lead to chips and cracks.
Therefore, such dirt must be removed immediately with a special scraper before the mass has had time to solidify or charred.
Cookware on the cooking surface can also get dirty:
- frozen grease spatters;
- soot from escaped milk;
- Dried stains of broth, compote, salt water;
- traces of contact with the bottom of aluminum or copper dishes
- stains from old carbon deposits on the bottom of pots or pans;
- streaks from dirty sponges, fluffy cloths, detergent residues.
Fresh dirt is removed better than stale dirt, so it is advisable to wash the stove as soon as it has cooled down.
Care products for glass ceramic hobs
The glass ceramic hob will get less dirty if you put perfectly clean and dry stainless steel or enamel cookware (no chips) on it. The second rule is to have special scrapers, sponges and cloths for it. Do not use a dishwashing sponge: it absorbs grease and makes the glass ceramic hob much dirtier. Owners of glass-ceramic cooktops should get hold of such accessories:
- A special scraper with replaceable metal blades (may be sold with the oven);
- Wet wipes with antibacterial impregnation for glass ceramics;
- Lint-free dry wipes, including double-sided Top House (the rough side for cleaning dirt, the smooth side for polishing).
You can also remove dirt (other than grease) with a melamine sponge, using an edge rather than the entire surface. Microfiber, lint-free cloths and paper towels are ideal for glass ceramic care.
Do not use harsh metallic sponges, abrasives, aggressive bleach, stain removers, oven sprays, and cleaning gels. Liquids, often in the form of sprays, creams, gels and pastes are used to care for the glass ceramic hob.
Liquids are good for removing fresh dirt, but a thicker consistency will do a better job on stubborn and persistent dirt. They can be divided into 3 groups.
- Professional products from the manufacturers of glass ceramic stoves (Electrolux, Bosch, Indesit). They are used by cleaning agencies when cleaning your apartment.
- Special means for glass ceramic from manufacturers of household chemicals (Top House, Topperr, Luxus Professional, Cillit, Sanita, Shumanit, Dr.Beckmann and others).
- Universal products for different types of surfaces, including glass ceramics (Grass Progress, Frosch), as well as dishwashers and glass cleaners.
How to clean a glass ceramic hob from old carbon deposits
The thickest layer of stubborn dirt is best removed with a squeegee. Before you do this, it is recommended to turn on the stove for a while, so that it warms up slightly, and the soot softens. If the stain consists of congealed food, you can pour a little water on it beforehand.
Wait until the board has cooled down completely before cleaning it with chemicals. Spread the cleaner sparingly and evenly over the dirty areas and leave it for the length of time indicated in the user manual.
Then remove the dissolved soot with a moderately hard sponge, wipe the surface gently with a wet cloth, and dry with a paper towel or polishing cloth.
Professional products are most effective, but if you do not have them handy, you can use improvised ones.
- Apply a paste of baking soda and water to the dirt.
- Dilute a dishwashing detergent in a bowl.
- Place a towel soaked in soapy water on top of the baking soda.
- After half an hour, wipe the surface with this towel and finish cleaning according to the standard scheme.
How to clean the glass ceramic hob from white plaque
Lime scale can be removed with ordinary vinegar diluted in half with water. After a couple of minutes, wipe the surface clean. To get rid of whitish streaks helps and ammonia solution 1:5, it soaks for 10-15 minutes.
It’s easier to prevent white plaque than to remove it. To do so, rinse all detergent and cleaning agents thoroughly and wipe the surface dry, using only clean sponges and cloths.
To make your stove work for a long time
Clean and dry your vitrified clay hob after cooking with new sponges, clean, soft cloths and lint-free towels.
It can be cleaned only after it has cooled completely, but plastic, foil, foods with high sugar content should be removed with a scraper immediately. You can use baking soda, vinegar, ammonia, dishwashing detergent and glass cleaner to clean your glass ceramic hob.
You can remove scratches from the plane in the following ways:
If more serious defects occur, it is better to contact a qualified technician. It is recommended to check the warranty period, if it has not yet expired, you need to take pictures of the damage and call the service center:
- It will be necessary to call a specialist for repair at home, so that he conducted an inspection and made a conclusion, whether the surface can be restored.
- If the warranty period has not yet expired, the surface must be taken for examination, which will determine the cause of the destructive effect.
- If it turns out to be a factory defect, the manufacturer is obliged to replace the glass ceramic element or the entire stove.
- When the warranty is no longer valid, you should visit a service center or repair shop.
Ceramic cooking surfaces are very convenient. Compared to cast iron burners, a ceramic stove conserves more energy and requires less effort to clean. at least in theory. After some time of use on any glass ceramic hob stains, stains, grease and more remain. The situation is aggravated by the fact that to clean such a hob you need to choose a special cleaner.
The product industry offers a huge selection of cleaners for glass ceramic surfaces. However, their significant disadvantage is the high cost. The good news is that you can just as easily use normal household remedies! Here are 8 effective ways to restore your stove to its former beauty.
We suggest to read What to remove the tape and remove the glue (traces) of the tape quickly and effectively
Cooktop sizes
Despite the fact that there are certain sizes, there are certain tolerances. Let’s start with the fact that the minimum width of the hob is 30 cm. The maximum width can be more than one meter. It already depends on the imagination of the manufacturer and the arrangement of burners (for example, not in a square or some other combination, but in one row). However, the standard length and width of a four-burner hob is 60×51 cm. But these are the dimensions of the top of the hob. The landing itself can range from 57 to 59 cm in length and 47 to 49 cm in width. The exact size of the seating hole can always be found in the operating instructions. There is also a maximum tolerance of error. often than not, it is acceptable to make the opening 1 cm longer in length and width. But keep in mind that if the cooktop is not drawn to the countertop, it may yank due to the large size of the hole. There are panels (e.g. Bosh), which have a tricky mounting mechanism at all.
Tolerances with this method of attachment are more critical and allow no more than 3 mm on each side. Therefore, before making a hole in the countertop, carefully read the instruction manual.
I don’t see the point in rewriting a collection of tips from the instruction manual here. But let me briefly go over the most common points that apply to each cooktop.
Installing the hob into the countertop. sealant.
It usually comes with a panel. If it is not found, then theoretically you can use any door or window thin seal. Thin because, on the one hand, the gap between the hob and the countertop should be as small as possible to prevent dirt from getting into the gap and, on the other hand, to ensure a snug fit so that water does not leak inside, under the hob. Never use double-sided adhesive tape or sealant, in general anything that can stick the hob to the countertop. In theory, the panel should last a long time, in practice, all sorts of mishaps happen and the panel has to be removed. Removing a glued panel without breaking it is very difficult. And re-installation will cause difficulties, because you have to remove the old “glue”.
Installing the hob into the countertop. how to cut a hole for the hob
The first thing to do is to make a marking with a minimum of tolerance. It is very important to maintain a right angle. I usually use the hob for this purpose. That is, from the near or far edge I draw one line. I put the necessary dimensions on it, put the panel on this line and draw two side lines. To avoid scratching the panel, I put some cloth under it. Lines will be strictly perpendicular, then measure the desired value on the two resulting side lines and finish the rectangle. It is very important to pay attention to the fact that you do not hit the side walls under the countertop when marking the hole . Further, the hole is cut out with a hacksaw or an electric jigsaw, whichever is more convenient for you. To start cutting, you need to drill a hole for the entrance of the hacksaw blade. You have to do it on the inside of the countertop. The one you’re going to cut. On a photo it is well visible, how it is made. Of course it would be better to make the cut with the jigsaw. The hole in the marble countertops or from artificial stone, it is desirable to entrust to the experts. However, keep in mind that the jigsaw’s pad is metal and can scratch the surface when working. To avoid this, you can use masking tape. Its convenience is that it holds well on the surface, but does not stick as strongly as conventional tape. Glue can be both directly to the marking line, as well as a little backward from it. The main thing is to seal the area that goes beyond the hob, but can get under the jigsaw metal platform.
Installing the hob into the countertop. the use of silicone
The cut of the hole for the cooktop (and basically anything else in the kitchen countertop) should always be treated with sealant. There is absolutely no difference what color the sealant will be. In this operation, the most important thing is how to seal the cut, so that moisture does not get into it. Although countertops are made of moisture-resistant material, they still swell when moisture gets inside. Only the cut itself should be sealed. It remains to wait some time (from three hours) for the sealant to dry and you can install the surface.
Here we can finish the article. If I remember something. I’ll finish it. If you have any questions, ask in Комментарии и мнения владельцев. I’ll summarize the most important points in this article.
Today, glass-ceramic cooktops have begun to replace conventional cooktops due to many advantages: ease of cleaning, heat indication of the cooktop, power. There are practically no problems with them, but cracks can appear on them if they are subjected to strong impacts or an excessive thermal effect.
And if some people are lucky and they have only a small crack in the corner of the surface, others have a defect that can cover the entire cooking area.
Cookware with thick or uneven bottoms, as well as aluminum cookware, not only reduce the efficiency of the glass ceramic cooktop, but can also leave behind noticeable marks on its surface. In addition, melted plastic and sugar can ruin the appearance of the product.
Manufacturers advise to follow a number of rules when using the glass surface: do not cook food on the cracked panel, do not touch the metal dishes with wet hands, the surface must be cleaned with special products, in order to avoid damage.
What to do if there are cracks and scratches on the hob
If the hob is cracked, it is recommended to observe safety measures:
- Do not use the technique for cooking;
- Do not touch metal cookware with wet hands; risk of electric shock;
- Do not try to repair the appliance yourself to avoid causing a short circuit.
A qualified technician is called to fix the problem.
Advice. If the appliance has not expired, then contact a service center.
In the case of a warranty case, a technician comes to the house, who conducts a visual inspection of the damaged surface. It determines whether the appliance can be repaired. Then the hob is taken away for examination to determine the cause of the malfunction. If you find a factory defect or breakage, which did not depend on your actions, the device is replaced with a new one.
If the warranty is no longer valid, call a specialist from a company or private company. They determine whether the damaged surface is repairable and repair the defect.
Scratches on the hob
A glass cooktop requires special care. Scratches form on its surface if it is not used properly. Superficial damages can be removed at home.
Important! Before removing irregularities, unplug the oven and let it cool down to avoid burns.
The following methods are used:
- Mix baking soda with water until it becomes a paste. Apply it on a soft cloth and wipe the damaged surface in a circular motion. Remove the remains of the baking soda with a paper towel, polish the hob dry with a dry cloth.
- Get a cream-paste for polishing metal (GOI cream-paste, Metal Polish, Doctor Wax, etc.) at the store.). Apply on a cotton pad or soft cloth. Wipe the entire surface in small strokes. Remove the remains with a paper towel. If the scratches do not disappear, use a brush with soft bristles.
Before using the product on the entire surface, apply it to a small area and test the reaction of the material.
How to repair a glass cooktop
Rochelle Leggett Updated December 27, 2018.
A glass cooktop offers many convenient features. For example, you’ll have fewer problems with food sticking to the surface, and children won’t be able to burn themselves as easily on a glass cooktop.However, glass cooktops also have drawbacks. They don’t go well with some types of cookware, and there are several ways to damage the surface. Some problems you may encounter with a glass cooktop are easier to fix than others.
Scratches
Glass cooktops are prone to scratches. Deep scratches cannot be repaired. However, if your cooktop has minor scratches or streaks, they can be polished. You can make a paste from baking soda and water or use metal polishing cream.Rub the paste with a soft cloth in a circular motion. Afterwards, wipe the paste with a cloth. If the scratch does not seem to be improving, stop. Polishing too much can cause the surface to fade, and the scratch will be too deep to fix. Do not use excessively abrasive substances to clean the hob, as you could leave more scratches.
Chips and cracks
If you drop something on the hob, the surface could chip or crack. Using a cooktop with cracked glass is dangerous and can cause an electric shock. The only way to make sure your hob is safe is to replace it or replace the glass. How you remove and replace the glass depends on your cooktop. Sometimes the glass is held in place by screws in the front of the hob; the glass is then lifted. Sometimes you need to remove the brackets under the hob and lift it to access the glass. In both cases, make sure the power is off before repairing.
Heating
Sometimes glass cooktops don’t heat properly.If the cooktop is not heating, the problem may be a faulty switch. Check the switches by disconnecting the power and then disconnecting the h2 and h3 wires from the switch connected to the unit that is not heating. Check the wires with an ohmmeter, which will determine if there is continuity in the switch or if electricity can flow properly in the switch. If there is no continuity, the unit probably needs to be replaced; if there is continuity, the switch is probably faulty. Overheating can also be caused by a faulty switch.
Preventing problems
There are several ways to prevent damage to the cooktop. Do not use coated pans and colored bottoms, as the paint can stick to the cooking surface. Aluminum or stainless steel cookware is best, though you can also use cast iron. Flat-bottomed, smooth-bottomed pans are best not scratched. Pick pots and pans, not move them around. Do not use the surface as a cutting board, and do not use it to store heavy objects. Be careful when moving full dishes so you don’t drop them on the surface or break the glass.If a pot containing a significant amount of sugar overflows or spills, the spill should be cleaned up as soon as possible, as it can cause marks or pits on the glass, which is fairly harmless but looks ugly. Allow the cooktop to cool slightly before removing these spills.
