Indesit wiun 81 control box

Control Panel

When the machine is adjusted, it is time to pay attention to the control panel, on which you can notice such elements:

Indesit wiun 81 control panel

If we take a closer look at the control panel, on the right side we can see four control buttons. The manual contains a lot of useful information about them.

The button to the right is used to turn the washing machine on. It can also be used to de-energize the device. Next to it, there is a button responsible for the program.

It can be used at any time to stop the washing without turning off the power to the washing machine. All this is done so that the user can change the settings if necessary. The buttons to the left are for selecting the desired function.

The display system works on an intuitive level. The lights above the buttons always tell the user that the corresponding function is active or disabled. If you look at the display on the left side of the control panel, there is a light on that tells you the washing machine is on. The indicator also lets you know that the hatch is securely locked and you can start washing.

If the manual is to be believed, the three indicators that are under the Indesit label will always show the active phase of the wash. If the overhead light is on, the unit is on and the laundry is being directly washed. Middle light informs about rinsing. At the finish line, the bottom light comes on. When this happens, it means the wash is finished and the items are now spinning.

Description of the washing machine

Detergent dispenser for the load-

The middle light tells you that the detergent and fabric softener. с. 8).

FUNCTION SELECT BUTTONS: are used to select

available functions. Button for the selected function

The START/RESET button is used to start the device

indicates if the washing machine is on and

Turns the washer on and off.

The SOFTWARE selector knob is used to select

In the process of running the program, the handle

How much do professional services cost?

Lack of experience in repairing household appliances is a reason to contact a specialist.

Only a professional can repair or replace the board. You can find a wizard by posting ads on the web or in the newspaper. Perhaps some of your relatives or acquaintances have already used similar services.

The part itself will have to purchase separately. If it is possible to restore the board, the master will take it to the service center, as it is impossible to perform such repairs at home.

To reduce the risk of meeting with scammers, you should read the reviews left by other customers. Honest craftsman will certainly give a guarantee for the work performed and certify everything with documents.

Repair with your own hands

Consider troubleshooting on different models of machines Indesit.

The device must be de-energized before repairing!

Wisl 82 and Wisl 83

The sequence of steps for replacing the bearing unit in a Wisl 82 washing machine with a plastic tank:

• disassemble the device, remove the tank with the drum;
• saw the tank along the soldered seam, separate;
• knock out the bearings, put new ones, lubricate, install the gland;
• Clean the drum;
• glue the tank halves with sealant, tighten with self-tapping screws and bolts;
• After the sealant has dried, reassemble the device.

Replacing the bearings in the Wisl 83 series:

• Remove the top cover
• Unscrew the powder tray fasteners, remove valves from inlet hoses
• take out the tray
• disconnect the supply hose and the drainage connection
• unscrew shock absorbers
• Remove the rubber seal from the hatch
• Remove the upper counterweight
• take out the side of the housing
• Remove bottom counterweight, motor, pulley.

Further repair is carried out as described for the Wisl 82.

Wisl 102

To replace the electronic display unit in the Wisl 102 model you need

• remove the top cover;
• Remove powder tray;
• Unscrew the fixing bolts and remove the panel with the control buttons;
• Disconnect the switch knobs;
• Unbend the locks on the back side of the panel, remove the unit;
• insert serviceable module, install and fix indicator panel.

Wisl 105

If there is a malfunction in the power supply of the control module on Wisl 105 (all indicators are blinking), the repair consists of the following:

• Remove the back cover;
• Remove the power control unit (located on the inside of the left panel below), remembering (photographing) the wiring diagram;
• Remove the cover, examine the board;
• locate the blown condenser;
• unsolder the defective part and replace it with a defective one (capacitor capacity 680 mF, 10 V);
• assemble unit, put in place, connect wires.

Wiun 81

To replace UBL (hatch locking device) on the Wiun 81 series unit, you need to:

• remove the door sealing collar;
• unscrew the UBL fixing bolts;
• remove UBL through the hatch, disconnect wires;
• Install a working UBL, fix it;
• dismantle the control module, inspect (if the UBL is short-circuited, the board may be damaged);
• Replace defective parts or the entire board;
• Assemble the unit, put it back in place.

Wisl 103

To clean the drain filter for the Wisl 103 model

• Wisl-103 The heating element has burned out, remove the plastic apron on the bottom of the front panel by hooking it with a screwdriver;
• put a container of water under the socket of the filter;
• unscrew filter, drain water;
• Ws 105 tx: Clean and rinse out the filter, remove foreign objects from its seat;
• install in place, screw in the threads up to the stop;
• put on plastic apron.

Ws 105 tx

When switching on the machine ws 105 tx program with hot water, the programmer knob turns without stopping, the washing does not occur. Causes of failure and repair:

• Faulty heating element.

Стиральная машина Indesit WIUN 81

• Remove, check contacts, test leads;
• install a working.

• Pump breakage.

• remove, check the integrity of the rotor, test the windings;
• Replace with new one in case of malfunction.

• Control board defect.

• dismantle;
• Repair the damage or buy a new one.

Wisl 85

Wisl 85 model lock indicator blinks fast, one of the modes blinks slowly. Cause. motor breakage, motor brushes are worn out. Repair work:

• Remove rear panel;
• Disconnect wires from motor;
• unscrew fastening bolts;
• dismantle motor;
• Check windings. Short-circuited, replace the motor;
• Remove brushes;
• Replace if badly worn;. Disassemble the motor. If minor, clean up with fine emery cloth;
• Reassemble motor, reinstall.

Iwsc 5105

Iwsc 5105 machine doesn’t dump water (F11 code. problems with pump). Corrective action:

• Disconnect wires from the pump, test them;
• If broken, replace wiring;
• Remove the pump, check the windings, inspect the rotor;
• If the pump is good, dismantle the power control unit;
• Check triac, resistors, relays. Replace the defective ones;
• Run spin mode;
• If the error is still there, replace the block.

Witl 86

To replace the heating element in the vertical model Witl 86

• remove the right side panel;
• disconnect heater and temperature sensor terminals;
• unscrew the fasteners, remove the heater;
• Check with a tester for short circuits;
• replace the defective one;
• if there is no damage, clean off lime scale with citric acid solution;
• put heating element and temperature sensor in place, connect wires.

Iwub 4085

Sequence of actions for troubleshooting of electronic power unit Iwub 4085:

• open the rear cover, remove the control unit;
• Connect PCB to PC, check errors in memory block using special program;
• if there are no errors, re-flash the device with the programmer. Firmware can be downloaded on the forums of repair specialists;
• assemble the unit, put it in place.

Wiun 100

Win 100 machine doesn’t turn on, error F12 (no communication between display unit and control module), defective module processor. Remedy:

• Remove module;
• connect to the programmer, fill in the firmware;
• if the computer indicates a processor error, replace;
• processor sp107156 (or its analog) solder in place of the failed one (skill required);
• assemble the unit, put it back in place.

Witl 1067

Witl 1067 vertical loading machine stops after starting. The reason: wear of brushes. Repair:

• Remove right side panel;
• unscrew wires, unscrew fasteners and remove motor;
• Remove worn brushes from the brush holders;
• insert new brushes so that the angle of bevel corresponds to the technical requirements;
• solder the contacts;
• Clean the collector with alcohol;
• Put brush mechanism on motor;
• Replace motor.

Troubleshooting and Repair of Indesit Washing Machines

Indesit Wiun 81 washing machine. Spins badly from time to time. Now it takes the powder out of the container with water, it seems to run water through it twice and that’s it. Standing and Thinking. Clicks some relays and stands idle. It’s letting the water drain out. But it won’t start and it won’t get any water in the tank. They said to check the pressostat and the tube that goes to it. Couldn’t figure out how to get to the end of the tube. To make sure it is intact. Goes out the edge of the tank to the bottom. Removed the rubber gasket on the door and wrapped it in the tank. Т.к. They said you can see the tube on the edge there. But I couldn’t see or feel anything. They also suggested to remove the tank, because it is possible that there is some dirt under the tank. How to take it off? And is it possible to do the cleaning without removing the tank? To check the pressostat just pump air into it to hear the contacts click?

The motor relay must be clicking. The belt is in place? The engine is turning? Motor brushes are “sticking out” of the holder more than 10mm? The pressostat was checked? The “tank empty” signal sends? The tube has two ends. One on the pressostat, the other on the extraction chamber. Carefully put the washing machine on the back wall. In the branch from the tank to the pump is inserted a sampling chamber (plastic cylinder). On it the second end of the hose to the pressostat. The brushes are on the motor, it is very easy to remove the motor. On the side, put it also see, but the holder from the motor must be removed, otherwise you will not measure the length of the output.

In operation Indesit washing machine Wiun 80, after starting any program all indicators go out except the indicator “washing with soaking” and all, nothing else happens, the door is closed.

If soak light is on, it is fault F01. Most likely a breakdown in the electric motor.

I have a washing machine Indesit Wisa 81 (4,5 kg). During the washing process the speed, rinse and door lock icons started blinking simultaneously (it was blinking very fast), and the sound was as if the machine was trying to pump water or scroll the drum, only it was not constantly humming, but cyclically trying to do something. I unplugged it, checked that the drum turns freely, waited 15 minutes, plugged it in again, the washer filled the water, scrolled the drum twice, and again the same thing happened. Please tell me what it may be?

If the spin and rinse indicators light up and the “lock” indicator blinks, then the error is F10. Water level sensor or control module can be defective.

Indesit machine Wiun 102 (3,5 kg) starts the washing, switches to the rinse mode and can not finish it, the speed does not pick up, the motor does not spin at high and medium speeds, the spinning does not occur, the pump regularly drains water into the drain, the heating element is working. What can it be?? Why the automatic washer-dryer does not finish the washing?

If the unit both drains and heats the water, the cause is most likely due to the deterioration of the brushes of the electric motor. Check the wear of the brushes, and if they are less than 2 cm, you need to replace them with new ones.

I have a washing machine Indesit Wisa 61, in general, the washing stopped in the middle, the water was left inside, had to drain through the bottom filter. Now I turn it on, first all the lights go on for 2 seconds, as usual, then I put any program, the red hatch lock light flashes, but the door does not lock and the start button does not work, the machine does not start, no sound, just stands and flashes the hatch lock light. Please tell me if it is the LAD or maybe something else? I took the control unit off, took it apart to see, there seems to be nothing broken inside, everything looks intact.

May be a breakdown LCR (door locking device) or control module. The LCR can be checked by installing an undamaged LCR as there is just a thermoplastic plate that may not work due to heat, check it in another way is not possible.

Faulty washing machine Indesit Wia 81. After washing, leaves a bit of powder, and almost does not take the conditioner, I open the tray, and in the compartment for the conditioner is water diluted, the water pressure is normal before it all worked, but it all started a couple of days ago, advise what may be the reason? And how to fix it?

Most likely, the electromagnetic water valve (EWC) is out of order or the filter in the valve is clogged. The valve on the water intake works only for water for washing and for air conditioner does not open fully.

Indesit Wiun 104 washing machine, blinking lock and extra rinse button. What can be the problem??

If the indicator light lock and flashing additional rinse, it is an error F01, which indicates a problem with the electric motor.

Washing machine Indesit Wiun 82 (CSI). Starts for a short time and stops after 2-3 seconds on any program. When replacing a new UBL (burned from the inside, also traces of burning over the UBL). The sunroof does not lock, the indicator light of the unit is on. What it may be? Can not find anything on the error display.

If UBL was really burned, it is necessary to look at the control circuit on the module. Triacs, resistors, diodes, are between connectors.

In use, the washing machine Indesit Wiun 104, not new. Drum doesn’t spin freely when turned off, as if it was jammed. I am wary of plugging it in. No transport screws observed. What do you advise?

If, transport screws are removed and drum is blocked, then perhaps 2 things: something got between the tank and drum and prevented the drum from rotating; bearings were worn out and destroyed, now the remnants of the bearing blocked the shaft. Also, we recommend checking the drive belt and electric motor.

Indesit Wia 100 washing machine. First, the water stopped draining. Replaced the pump. Checked by typing and draining, everything worked. Decided to do the wash, the water came in, a couple of rotations and stopped. Restarted program, turned on, washing cycle proceeded normally. Standing on rinse. When starting the program, the washing light is on, but nothing happens, if you just turn the switch, then after a few seconds the water intake and drain mode is on. Indicators for “rinse” and “spin” light up, blink, and very often the door lock blinks. From what I did. Change pump, replace motor brush. Checked the temperature sensor, heating element, everything works fine, checked and cleaned the filter and hoses. lifted the drain hose above 50 cm, checked the circuit board. did not help.

You have already replaced almost all the parts, I hope before replacing them you at least checked them with a multimeter and megohmmeter. If the rinse and spin indicators are on and the lock is blinking, it is F17 (hatch lockout error).

Faulty washing machine Indesit Wiun 80. Start indicator light stops blinking when washing mode is on. Washing machine does it’s job. Drum turns normally on washing and rinsing modes when emptying. But the drum just rotates in spin mode, does not pick up a revolution, the laundry remains wet.

If the engine does not rev up during the spin cycle, this can be due to the following problems. a broken drain pump; if there is water in the machine, the motor simply cannot spin with it. Worn brushes or drive belt; malfunction in control module or speed sensor (tachogenerator).

Indesit Wiun 105 cis washing machine. Help me determine the error code. In the table of error codes, I did not find. Or maybe I do not understand something. Blinking lights. “spin speed”, “fast wash”, “door lock”. The heating element has been replaced. But the problem remains. For example, on the 9th program: the washing passes, the rinse indicator turns on, nothing happens for a minute, and then the lights start blinking.

Installed and connected washing machine Indesit Wisa 81. After washing ceased to produce a characteristic click that reached the end of the wash light and red light at the end of the wash light is permanently lit does not flash (as is supposed to after a click), and after returning to zero the knob does not go out red light, lit constantly, I have to unplug it from the socket.

If after the end of the wash, the light continues to flash the hatch lock indicator, the cause may be a failure of the OBL (Door Locking Device) or control module. Also, check to see if the water has drained at the end. If not, that’s why the hatch won’t open. In this case you need to diagnose the drain pump.

Can you tell me why the machine Wiun 82 does not turn on the indicators when plugged in and then after 15 min. Turns on: the indicator light on the hatch button and the speed, but the washing machine does not work, and the buttons blink rapidly.

If the blinking RPM indicator and lock, it is error F01, which is related to the lack of rotation of the drum.

Indesit Wiun 105. Not enough power to turn the drum, rattles. Started the wash, the process began. After a while I come in and see that the machine in rinse mode can not turn the drum. Turns at 1/4, buzzes and can not go further, then the voltage is removed from the motor and it returns to the same place. Same thing the other way. After a few times the speed increases and seems to accelerate. But it sounds like a rattle. Removed the motor, found a missing lamella on the manifold. I rebuilt it with copper flex, poxypol and a soldering iron. I also sharpened the brushes, because they had chipped a little bit. Resharpened the new lamella as much as I could (no lathe), but I still had the ratchet sound when I install the brushes, but it is not so bad. No step to the touch though. Turned it on and cranked it a few times. Then the same thing happened again. I thought the lamella had fallen off. I felt it with my finger. in place. Removed the motor, the lamella was in place. Re-soldered the wire to the blade. I put it back in. At some point I heard the click and the blade broke off again, obviously from overheating. The cycle was somehow achieved, but it was sparking, smelled like burning, obviously the manifold was heating up a lot. I’m curious about this: from the symptoms, it looks like it’s just the motor. What baffles me is that it stopped working before the lamella snapped off again. Although I understand that the manifold was not perfectly round and the brushes are not lapped, so it was sparking and heating. But that could be a problem with the control unit? Either it works or it does not work at all?

The lamella doesn’t just fall off, it is most likely short-circuited (and overheated), change the motor and you will be fine. One in one winding is enough, the others may be normal, but the motor will not work.

Wia 101 washing machine Indesit Wia is installed and connected. Water is squirting out of the powder compartment during the rinse cycle. What could be the cause? Drainage filter is clean. Tried running it, as soon as the water started pumping, it started spurting out over the ditch. And the filter, for example, in the form of a grid, is not in this pipe?

A lump of powder stuck in the nozzle. Clean the one at the top (tank tray). There is no mesh in this spigot. You need to remove the tube and clean it well. It’s accessible through the top (with the lid off) and from the front, through the manhole collar removed from the front.

Washing machine Wiun 81 csi. All LEDs light up and go out and the red lock is blinking constantly, the door lock does not work when you press the start button, the red lock goes out, the door lock works.

Probably there is a problem with the DIB or control module.

The machine Indesit Wisa 101, by the end of the wash does not spin and does not drain, flashing indicators of spin speed and dirty laundry. When switching to spin mode, water goes out and spins as needed.

If indicator of spin speed and dirty laundry lights up, it is error F12 (no communication between module and indicators). The control module is most likely malfunctioning.

Using a Wiun 100 washing machine. When you press the Start button, you hear the hatch door lock sound, it locks, but the hatch lock indicator light does not come on. The machine does not start to fill up with water and the washing process does not start. The hatch can then only be opened after turning off the unit for 10-15 minutes. Water is coming in, pressure is normal, no additional indicators light up. What can be the problem??

Most likely, the problem is either in the control module or in the heating element (water heater).

Wiun 103 washer. Leaking from underneath. Took it out, took off the back cover, took off the top panel. Disassembled the dispenser, looked, everything is fine, put it back together. Checked all the hoses, spigot, tank for mechanical damage. Everything is normal. Decided to get 2 stools, put the unit on them. Put a bucket in the bottom, threw a jacket and turned on the wash for 30 minutes (did not put the back cover and top hat, to have an overview and the opportunity to find the leak). And so passed about 20 minutes, the washing machine in working order took in and out of water, everything worked like clockwork. And so, when the 3 mode “spin” turned on, a little while ago, the working machine began to pour a jet at the moment when it is silent for 10 seconds and with the drum not spinning begins to drain. And through the open back cover I found a leak. As I understand it, during transport, there are 4 screws to fasten the body to the drum. Naturally, when the unit is brought to the house, the screws are unscrewed and turn it on, and it works in perfect condition. But here’s the paradox, it’s the bottom two bolts that are leaking. Please help me, tell me what to do?

They’ve overtightened the bolts or screwed the wrong ones in. Now only to seal these holes. You can screw suitable screws greased with sealant into the holes.

The machine Indesit Wisa 101. I turn on, the hatch lock blinks, I select any program or function, the program LED is lit and the lock goes out, and the hatch is locked, what to do?

It is very important which lights are lit when the power indicator (lock) is flashing.

In operation Indesit washing machine Wiun 105. Last night I put my clothes in the wash and put it on normal mode and it is still running, I turn it off and put it on spin, but it is still running and the water is not draining. You can’t get the stuff out.

The causes of such work in a faulty drain pump. The water is not drained and in order to avoid leaks, the hatch does not open. First thing to do. Drain water through the drain filter. After that, unplug it for 30 minutes. Most likely after these manipulations the hatch will open and you can take out the laundry.

Indesit Wia 80 (5 kg load). Turn on, runs in washing mode for about 10 minutes. Then stops, starts flashing lock, rinse, spin, simultaneously pumps water. Unplugged, plugged in after 20 minutes, same cycle happens. By the way, the drain pump cleaned.

If the spin, rinse and lock is blinking. it is error F03. Most likely it is in the water heater, if it is good, then check the temperature sensor.

The problem with the washing machine Wiun 81, in operation for 1 year. The problem is the following, after washing in any program the washing machine stops after switching on the “rinse” mode and starts blinking “lock” and the “rinse” function selection indicator (next to the “Reset” button). To continue the wash must turn the lever to the program “rinse” and then it will continue to rinse and spin, but directly from any program no rinse or spin does not happen. What is the error when the lock and extra rinse blinks??

If the lock and auxiliary rinse indicators are flashing. F01 error, that means there is a defect in the electric motor.

Washer Wiun 102 (CSI) stops during the rinse. Replaced the drain pump because the inside, where the armature. stator, the water got into the vertical looseness of the impeller. After one successful wash, the daily wash (30m) starts.), in other programs (intensive, 60gr., 90gr cotton.) The defect repeats. stops before rinsing, the rinse indicator light on the control panel lights up and the start/pause button starts blinking. Everything starts manually and keeps running. Checked the brushes on the motor. Ideally, the heating element has been removed. Resistance on terminals 29 ohm, resistance of the temperature sensor at room temperature 22kOhm, the pressostat tube is not clogged, with a slight blow to the pressostat, the contact clicks.

Most likely you need to firm up the memory chip, which is located on the control board.

Indesit Wisa 61 after washing begins to spin and stops, starts flashing “800-400” and “lock”.

If the RPM indicator and the lock indicator blink. It is error F01 which means there is a defect in the electric motor.

Using a washing machine Wiun 81. After washing, it does not open, “rinse” button blinks when pressed. The washing machine does not respond to any program, there is no water in it, it is locked, the lock indicator light is on. If disconnecting and de-energizing the lock still doesn’t open.

If the hatch lock is not removed even by unplugging, then for starters, try draining the water through the drain filter and try again unplugging. If it does not help, then the LCR (hatch locking device) is out of order and only a mechanical disassembly of the top lid and unlocking with either a screwdriver or a cable unlock will help.

Indesit Wiun 82 (csi). Has been running for 7 years. Problems began 2 years ago, in washing mode, poured water and after a couple of seconds drained, put the valve on the drain. helped. Filled with water, then the pump turned on for 2-3 seconds, then stopped for 10 seconds and then continued with the program. Now behaves as follows: fills with water, turns on the pump and with it the bleach indicator and the hatch lock (blinks often), and stops responding to everything except “plug out of the socket”. In the rinse mode starts, but before the first drain, that is, when you turn on the drain. Indicators, by the way, the water drains normally, the pump inside is clean. In the spin mode all the same, but if at the moment of activation of the pump forcibly rotate the drum (respectively the motor), the spin starts and to the end according to the program. In washing mode similar Focus does not pass. Boards are clean, visually no damage. Burning, no.

Check error F01. motor. The length of the brushes should be at least 15 millimeters. If not, replace motor triac. Remove the motor and check separately on the table. Protein all the lamellae collector in pairs (the norm is 2-4 ohms, if somewhere will be 10 or more the engine for replacement).

The washing machine Indesit Wia 102 (4 kg) has an electric valve constantly on, because water is always flowing from the drain hose. As a result, it does not fill with water.

It is necessary to check the solenoid resistance of the water valve, it should be from 2 to 4 kOhm., If the resistance is less or more, then the water valve must be replaced with a new one.

Indesit washing machine Wiun 103 in operation. After washing turns on rinse, then begins to drain the water, turns on the spin at low speed. Spinning at low speed and the pump running (draining) endlessly. After a while you hear an attempt to switch to a further mode, but nothing happens. The wringer and pump can run indefinitely.

First, you must check whether the machine is emptying the water, without the water drained the spinning will never start and the drum can spin for a very long time, try at this point to drain the water through the drain filter and if the spinning is finished, it may be due to a faulty drain pump.

Washing machine Indesit Wiun 100. When the spin cycle begins at any program, it continues indefinitely. It can spin at 1000 rpm all day long. When the programs “spin” or “delicate spin” are set separately, everything runs correctly. The heater is normal, no clogs on the level sensor. Pressostat hasn’t been changed. The pump is normal. Firmware?

Indesit Wiun 81 washing machine. The machine stopped starting the washing program after a power outage. Now, after starting, the lock indicator lights up for a few minutes, then it starts making noise, and the lock and extra rinse indicators alternately flash on the panel. Disassembled it to check the control module. There was a little smoke on it, but after checking it turned out to be working. Besides the module, there is soot on the phase wire of the lock (the entire wire is black up to the lock), but the lock works fine when it is turned on (it seems). So, what is it and what kind of error is the washing machine trying to tell me?? Try to replace the lock or it is not the problem?

Take a tester and check all actuators.

Wiun 105. Does not turn on, after a few minutes the red light on and with less frequency the leftmost light on the spin speed button blinks. Does not respond to anything. Apparently, the error is F08. Checked the heating element, water temperature sensor. I took off the arkadia control box, it has traces of oxide, I cleaned it, the error has not changed.

F08 error. the machine doesn’t heat the water. Check the heating element by measuring the resistance and the “breakdown to the body” of the water heater. Also check the pressostat and water valve. Module failure in this behavior is extremely unlikely.

Indesit Wisa 81 With any washing program, it immediately switches on rinse and drain. And so on without end. It is stuck. What to do?

The cause of malfunction can be a damaged control module or heating element (water heater).

The Wiun 102 washing machine malfunction. No more water coming in. Water inlet comes on a couple of times and that’s it. Silence. Washing mode does not turn on. But the rinse, spin and drain mode works fine.

If water comes in during rinse, water shut off. Solenoid water valve, consists of two parts. The first one pours water for prewash and main wash, and the second one. on the rinse. Most likely, part of it broke down and now you need to replace the valve with a new one.

The Wiun 103 washing machine. I press the “start” button, everything works, everything turns on, I select the washing program, then the temperature mode and start the unit by pressing the “start” button, I hear a little hum (probably the water pump hums) for about 2 seconds, and then silence, the washer simply stands and nothing happens (although it should continue to take in water). Checked in different modes, the spin works, the drain works, but the water intake, most likely does not work, and I can not understand why.

Wiun 100. I can not determine the error code. Only one LED (clock) blinks, and the lock blinks very fast. Main problem: I choose any mode, locks for a second, starts the selected mode, relay clicks and everything stops. The lock after that only opens after unplugging from the socket. Waited 15 minutes without turning off, the pump is working and two LEDs are flashing.

F02 error. Malfunction in the motor.

Podskite, I can not fix the problem with the washing machine Wiun 82. When switching on any washing program, the process of washing starts, then the water drainage starts, to activate the automatic rinse mode, the water drainage is complete, the drum starts rotating, and then it spins to infinity, without switching to rinse mode. What might be the problem?

Failure of the washing machine Wiun 102, periodically going into rinse mode, stops at the fact that it can not drain the water, and the motor is noisy. When turning off and on again, it refuses to drain, although the motor continues to hum. When the problem first appeared, the 500/1000 rpm lights were flashing, heavily soiled laundry and locking lock. Please tell me what this error is? Sometimes in rinse mode completes the entire cycle without any problems. The filter is clean and so is the drain hose.

The machine Wiun 100 draws and drains water only on one function “cotton, regular wash 60”, the other programs are working properly. What to do?

In your case the cause could be: a failure in the control module. simply restart the unit by unplugging it for 30 minutes; failure of the water level sensor; failure of the heating element (water heater).

How to determine the malfunction?

than 45% of problems come from the brains of the washing machine. If not taken, they can provoke breakdowns of the executive organs. Here are the most obvious signs of control system malfunction.

• Inadequate “behavior”. Machine spins drum frantically, drains and fills water in cycles for no reason.
• Does not turn on. Indicators on the front panel are not lit, the machine shows no sign of life at all, but it is definitely plugged in.
• Freezes when trying to turn on. Red LEDs are lit on the panel, self-diagnosis does not stop.
• Does not operate and generates error. Error code is displayed and sectors may not light up.
• Does not wash according to program. Performs erratic operation, instead of 30 minutes, can wash for an hour or two.
• Washing temperature mode is not followed. The temperature discrepancy can be read on the display or thermometer, or by touching the glass door.
• Random blinking of indicators on the panel. Diodes are blinking or glowing all at once, and unclear symbols appear on the display.
• Excessive heat around the motor or heating element. It can be detected by touching the housing. But only if the ground connection is present.
• Inadequate drum rotation. The motor may stop in the middle of washing or suddenly begin to rotate in the other direction.

If these symptoms appear, turn off the washing machine immediately. If they appear after repeated start-ups, it means that something is wrong. It is necessary to distinguish between control unit faults and other. For example, low speed and noise may be caused by slipping of the drive belt. Incorrect temperature may be due to a relay. Some models have a self-diagnostic function that will tell you about the problems. Its action is described in the instruction manual, and is usually triggered by pressing all the control buttons at the same time.

How to find the breakdown of the Indesit washing machine

In search of answers to the question: how to fix the washing machine Indesit. you can refer to the instruction manual. If you have lost the manual, we will give you the detailed algorithm of how to find the breakage and its cause.

• If your model has an electronic display, fine! The self-diagnostic system will display fault codes on it when it detects a malfunction. The following error codes are typical for Indesit washing machines: H20, F02, F05, F10, F18 and others.
• If there is no display the machine will let you know anyway, the lights will light up in a certain combination or sequence. Some malfunctions can also be detected by simply listening to the drum and motor. if there is a malfunction, you will hear a noise, hum, whistle, clang, or other unusual noise.

• Also take a tester, with which you can test all the sensors, contacts and wires. If there is no power in any of them, then you can judge a breakdown.

Warning! Before you disassemble the body of the washing machine, you need to study the structure of the washing machine. In this case the circuit diagram of washing machine Indesit will help you.

If you can’t find it, sketch, write it down, take pictures or video-camera all the steps of disassembly to assemble everything back correctly.

Your appliances can break down for a variety of reasons. Below are examples of the most frequent breakages:

• The tubular electric heating element is not coated with a protective composition, so parts break.
• Bearings break down. Replacing these parts is quite time consuming, so don’t fix the problem yourself. Contact Myguru service specialists.
• Electric motor sensor defective, capacitor problems. They can not be repaired you need to replace them.
• The control unit malfunctions. This is one of the most vulnerable places of the Indesit WIUN 81. The appliance does not start, the error lights are lit. This is a complex repair, which should be entrusted to a professional technician.
• In this model, usually after 4 years, the mains filter breaks, which leads to interruptions in the washing process.

Repair cost

Name Price

Basic services
departure of the master	free of charge
Master trip outside Moscow Ring Road	40 /km. from the Moscow Ring Road
Diagnostics	free of charge
Simple repair (class 1)	from 500
Repair of medium complexity (class 2)	from 900
Major repairs (class 3). complete disassembly	from 2500
Removal from a hard-to-reach place	from 400
Removal of foreign objects (without disassembly)	from 500
Removal of foreign objects (with disassembly)	from 1500
Repair
Electronic module	from 1500
Dismantling of transport fasteners	from 200
Adjusting of drive belt	from 400
Closing the drum flaps (complete disassembly)	from 2500
Cleaning the drain system	from 1400
Unlocking and opening the hatch	from 500
Timer	from 1500
Dryer cleaning	from 1400
Tank (including mounting/dismounting)	from 1800
Closing of the drum flaps	from 1200
Replacing
Buck (without drying)	from 3000
TEN	from 1300
Door seal for narrow machines	from 1400
Power filter, condenser, buttons / keys, power cord	from 600
Back tank lid	from 2500
Hatch hinge, hatch key	from 700
Drive belt	from 700
Whole drum	from 3000
Saucer seal	from 1300
Door handle, drum pulley	from 900
Support, cross	from 2400
Motor / motor (removal and installation)	from 1300
Upper counterweight	from 900
DEA	from 1100
Drying timer, temperature sensor, constant temperature thermostat	from 800
Timer, electronic module, indication unit, ROM programming	from 1300
Heating element of dryer, drying fan motor	from 1000
Pressostat	from 900
Drain pump or pipe	from 1300
Shock absorbers, springs	from 900
Tank (with drying)	from 3500
Bottom or front counterweight	from 1900
Control knob	from 500
Fill hose	from 500
Electric harness	from 1400
Drain hose	from 600
Temperature control sensor	from 900
Filler valve	from 900
Door cuff on machines with dryer	from 1500
bearing and oil seal	from 3500

.

the price is for labor only, without spare parts. Depending on your budget, you can choose the original part or an inexpensive analogue.