Repairing the sealing rubber on the refrigerator Biryusa
If the rubber seal on the refrigerator door is slightly deformed, it can be repaired. The fridge should be in horizontal position, stand straight and not skewed. To begin with, the seals should be cleaned with ammonia alcohol from dirt, dust, etc.
Ammonia alcohol cleans grease, dirt and makes rubber seals pliable.
Now it is necessary to find a place of deformation of the seal for what we take an ordinary sheet of paper and press with a refrigerator door, where the sheet will be movable, this place is damaged. If the deformation is not more than two millimeters then it is possible under the seal itself to put a material that will fit the size.
- You can heat the rubber band to seventy degrees, then you need to give the seal the desired shape and glue it to the door of your refrigerator;
- You can also use hot water, but in this method it is necessary to water the seal with boiling water until the rubber band is heated, then give it the desired shape;
How To Fix Refrigerator Door Seal
Another more complicated way is to use a steam iron.
You can also check for leaks with a flashlight. The flashlight should be placed in the refrigerator, then along the perimeter of the door to view for gaps.
Installing a new sealant
It is not enough just to buy it, you need to replace it, and then be happy with the result. But to be pleased with the result, you need to know how to make the replacement. It is better to attach a new rubber band to the old one in the same way as the old one was attached.
- If the old rubber was glued, the place should be degreased beforehand. What tool to choose to work. described above.
- For screwing the gasket with the screws, you need to take a slightly larger diameter than the ones that were. This is done because the holes have loosened over time, and in order to hold a new sealant, screws of a larger diameter are required.
After installing the rubber band on the door Biryusa, you need to wait until the adhesive dries completely. Check the quality of the work done, and only after that the refrigerator Biryusa should be plugged in and used as intended.
For the first time after replacement of the sealant, it is necessary to observe the refrigerator operation. Also it is necessary to have a closer look at the gasket itself to see that there are no gaps or skewed rubber. This may cause the door to be loose. You can see that everything was done correctly by the way the door opens: it should be done with a visible effort.
Rating of popular refrigerator gaskets
The life span of the rubber seals can be extended. There are some rules to follow, it’s important to handle your refrigerator with care. The door should be opened by the handles, do not touch the tape. When defrosting and washing the unit, it is obligatory to clean the gum, its recesses with solution of soda, using a soft toothbrush.
To make the seal flexible and soft, it is treated with the silicone grease, which is renewed after each wash. It is prohibited to soften the seal with any oil.
Door seal of the refrigerator Biryusa 14, 76 55 cm
Magnetic sealing gum for the refrigerator. The color of the seal is white.
Payment: You can choose to pay for the goods upon receipt or by bank card on our website when placing your order.
Notifications: For your convenience, we send a PACKAGING CODE and notification of the shipment.
The presence of flexible magnetic insertion included in the complete set of the seal provides uniform tightening of the seal on the whole perimeter of the door. The type of sealant profile is suitable for self-installation. Installation of the new seal allows you to avoid formation of ice in the refrigerator, extend the shelf life of food and increase the service life of the refrigerator compressor
We have the seal in stock.
Seal sizes: If you doubt the seal sizes shown in our catalog, we can make a new one according to your measurements.
What is “Order by 1 Click” If you don’t have time for the standard ordering procedure, or if you don’t want to understand the payment methods and delivery options, you can specify your name and phone number. The whole procedure will take you literally a few seconds. Our manager will contact you to specify all the data you need for your order and give you advice if you have any questions.
Warranty We are confident in the quality of our products, if you are not satisfied, we will refund your money! We give 1 year warranty on any product.
Video review of Biryusa 14 freezer door seal
If the seal is fixed on screws (self-tapping screws)
Video instruction on replacement of the gasket of the refrigerator NORD 233
- Open the refrigerator door.
- Remove fixing screws (self-tapping screws)
- Remove the old seal.
- Insert new gasket beginning from the corners and gradually pushing the “tail” under the plastic liner (mounting clamping strip).
- Fix the new seal with screws (self-tapping screws) all around the perimeter of the door.
- Then, if necessary, adjust the door (hinges) and warm up the seal.

A) adjust door height in case of sagging (bushings wear out) using washers of suitable inner diameter, putting them on the door fixing rod. B) Adjust the door if the seal is jammed on the hinge side by placing washers under the hinge mounting bolts. B) in case of loose connection of gasket, warm it up with technical or industrial hairdryer at air temperature of 200-250 °С.
Video instruction on how to determine. Measuring and selection of type of the refrigerator door seal profile.
Measurement of the height and width of the sealing frame is made along the external contour of the seal.
The measurements of the sealing frame should be made strictly on the refrigerating equipment and not in the dismantled state. For accuracy of measurements we strongly recommend to use a construction tape measure. All the differences in measurements and tabulated values in the catalog are most often due to deformation of the sealing frame during its long term of operation.
All measurements should be accurate to 0.5 cm. During measuring it is worthwhile to see how the door seal is fixed to the refrigerator door: a) “Glued under the panel” fixing type (IN, MA and other profiles).). Seal is glued between the metal body of the door and inner plastic cover of the door. b) Type of fastening “Under the strip. Screwed on screws (self-tapping screws)” (profile P1, etc.).). The seal is screwed on self-tapping screws through the metal holding bar (plastic door panel). c) Type of fastening “In the groove. (“tongue and groove”) (profiles E1, OM, etc.).). The seal is inserted into a mounting groove located all around the inside perimeter of the door.
Door seal for refrigerator Biryusa 14, 76 55 cm
Magnetic sealing gum for refrigerator. Color of sealant is white.
Payment: you can choose to pay for the goods upon receipt or by bank card on our website when placing your order.
Notifications: For your convenience, we will send a PACKAGING CODE and notify you of the shipment.
The presence of flexible magnetic insertion included in the complete set of the seal provides evenly tightening of the seal on the entire perimeter of the door. The type of gasket profile is suitable for self-assembly. Installation of the new door seal enables you to avoid ice formation in the refrigerator, extend the period of food storage and increase the service life of the refrigerator compressor
The sealant is available.
Seal sizes: If you have doubts about the dimensions of the seal shown in our catalog, we will make a new seal according to your dimensions.
What is “Order in 1 Click” If you don’t have time for the standard ordering procedure, or you don’t want to understand the payment methods and delivery options, you can specify your name and phone number. The whole procedure will take you literally a few seconds. A manager will contact you to clarify all the data you need for the order and give you advice if you have any questions.
Warranty We are confident in the quality of our products, if you are not satisfied, we will refund your money! We give 1 year warranty on any product.
Video review of the door seal of the freezer compartment Biryusa 14
If the seal is fastened on self-tapping screws
Video instruction on seal replacement on the refrigerator NORD 233
- Open the fridge door.
- Remove fixing screws (self-tapping screws)
- Remove old seal.
- Insert the new gasket, starting from the corners and gradually tucking the “tail” under the plastic trim (mounting clamping strip).
- Secure with screws (self-tapping screws) the new seal around the perimeter of the door.
- Then, if required, the door (hinges) shall be adjusted and the seal shall be warmed up.
A) adjust the door height in case of sagging (bushings wear out) using washers of suitable inner diameter, putting them on the door fixing rod. B) to adjust the door in case of a jammed seal on the side of hinges, putting washers under the bolts fixing the hinges. In the case of a loose fit seal, warm it with a technical or industrial hair dryer at a temperature of air flow 200. 250 ° C.
Video instruction on determination. Measuring and selection of refrigerator door seal profile.
Measure the height and width of the sealing frame on the outer contour of the seal.
The measurement of the sealing frame must be performed strictly on the refrigeration equipment and not in the dismantled state. To measure accurately, we strongly recommend the use of a construction tape measure. All differences in measurements and tabulated values in the catalog are most often due to deformation of the gasket over its long service life.
All the measurements should be accurate within 0.5 cm. While measuring it is worthwhile to see how the gasket is fastened to the fridge door: a) Fastening type “”Glued under the panel”” (profiles IN, MA, etc.).). The gasket is glued between the metal body of the door and the inner plastic lining of the door. b) Type of fastening “”Under the ledge. Screwed on with screws (self-tapping screws)” (P1 profile, etc.).). Seal is bolted on self-tapping screws through the metal holding bar (plastic door panel). c) Type of fastening “In the groove. (“tongue and groove”) (profiles E1, OM, etc).). The seal is inserted into the mounting groove located along the entire inner perimeter of the door.
Sealant for refrigerator Biryusa 6. found 370 items.370 goods
Sealing rubber for refrigerator BIRUSA 6. Frame 134Х55 You need the sealing rubber for refrigerator Biryusa? Our experts will choose for you the seal you need and deliver anywhere in Russia
Color of sealant white. Presence of flexible magnetic insert which is included into the complete set of the seal provides even adherence force of the seal on the whole perimeter of the door. The type of the seal profile is suitable for self-installation
BIRYUSA Refrigerator seal (5601100mm) 135, 139 for the refrigerating chamber Features: Type: accessory Accessory type: seal Designation: for a refrigerator Location in a refrigerator: in the door of the refrigerating chamber Method of attachment to the refrigerator door: inserts.
BIRUSA 8, 14 refrigerator door seal. new sample size: 550h760 mm Mounting method: inserted into the groove Second
Type: accessory, purpose: for refrigerator, device manufacturer: ATLANT, accessory type: gasket, length: 1337 mm, width: 543 mm
Refrigerator seal Pole (5301100mm) 2, 5, 7, BIRUSA 2, 3, 10, зам. 0002301000 Features: Type: accessory Accessory type: gasket Appointment: for refrigerator Material: rubber Color: white Width: 530 mm Height: 1100 mm Suitable for models: Pole 2 Pole.
BIRUSA Refrigerator Seal (550820mm) 226, for a refrigerating chamber, groove fixing Method of attachment to the door of the refrigerating chamber: sliding into the groove Specifications: Type: accessory Accessory Type: seal Designation: for a refrigerator Location in a refrigerator.
Purpose: for freezer, device manufacturer: Bosch, accessory type: seal
Manufacturer: Biryusa Appointment: for refrigerator Accessory type: gasket
Seal of the refrigerating chamber for refrigerators Biryusa-8, 14, 15. Size: 55х76cm
Type: replacement part, purpose: for refrigerator, manufacturer: ATLANT, type of accessory: gasket, location in refrigerator: on the door
Door seal of refrigerator Pole-10 560x1280mm Suitable for models: Pole-10
Door seal for refrigerator saratov (460970 mm) saratov 1524M Seal size: 460 x 970 mm Material: rubber Profile: P1 Suitable for models: saratov 1524M
Color of the seal is white. Presence of flexible magnetic insert included into the complete set of sealant provides the uniform effort of adjoining of sealant on all perimeter of a door. Seal profile type suitable for self installation
Refrigerator compartment seal for Bosch refrigerator (00245015)
Purpose: for refrigerator, device manufacturer: Bosch, Siemens, accessory type: gasket
Manufacturer: Biryusa Appointment: for refrigerator Accessory type: sealant
Manufacturer: Biryusa Designation: for refrigerator Accessory type: panel
Single-door appliance with a freezer inside the main compartment. The model is economical because of power consumption class B. Due to its small dimensions, the refrigerator will fit perfectly into a kitchen of the smallest dimensions and will also be suitable for office or country houses. Despite the.
The color of the seal is white. The presence of a flexible magnetic insertion included in the complete set of the seal provides even tightening of the seal on the whole perimeter of the door. Type of the gasket profile is suitable for self-installation
Shield (panel) of the freezing chamber of refrigerator Biryusa. Art. 0022000010 Size: 46,515,11,2 cm. Material: plastic. Color: white. Country of manufacturer: Russia
Color of the sealant is white. The presence of a flexible magnetic insert included in the set of seals provides uniform strength of the seal around the perimeter of the door. The type of profile of the seal is suitable for self-installation
Seal color white. The flexible magnetic insertion provided in the set of sealant provides equal tightness of sealant connection along the whole perimeter of door. The type of gasket profile is suitable for self-assembly
Specification: Part No.: 769748901603 Compatibility: Atlant, Minsk Location: freezer compartment Dimensions: 560×720 mm
Type: spare part, purpose: for refrigerator, device manufacturer: ATLANT, accessory type: seal, location in refrigerator: on the door
BIRUSA 460, 520 refrigerator door seal Size: 650х1615 mm Mounting method: slotted into the groove Second
Specifications: Part No.: 769748901502 Compatible: Atlant, Minsk Location: freezer compartment Dimensions: 680×556 mm Analogue: 331603301000 for models: XM-50. XM-40. HM-60. ÌÕÌ-17. ÌÕÌ-16. KSHD-151 300-115. KSHD-152 330-115
Seal of the refrigerator BIRUSA (5701270mm) 146, 237, 542 for the refrigerating chamber
If delivery is more expensive than the goods. dispatch only on prepayment.
BIRUSA refrigerator door seal (5701270 mm) 146, 237, 542 for freezing chamber
- Type: accessory
- Accessory type: gasket
- Function: for refrigerator
- Location in the refrigerator: in the door of the refrigerating chamber
- Method of attachment to the refrigerator door: plugged into the groove
- Material: rubber
- Type: white
- Width: 570 mm
- Height: 1270mm
Seal of refrigerator compartment BIRUSA (570820mm) 125, 129, 131, 148, 149 for freezing chamber
If delivery is more expensive than the product. dispatch only on prepayment.
Door seal of refrigerator door for freezer compartment of BIRUSA 125, 129, 131, 148, 149
- Size: 570 x 820 mm
- Method of fixing: inserted into the groove
- Second
Fridges Biryusa, produced in 60-80-s work properly in the kitchens of urban apartments and rural houses, cottages and garages. With timely scheduled maintenance their service life can exceed 40 years. The equipment does not require large investments, it is enough to buy a sealing rubber and replace it. This will ensure the normal operation of the compressor unit, reduce energy consumption. We offer to buy a compressor for any model of Biryusa in our company.
Door gaskets for Biryusa: quality, reliability, durability
Sealing tightness depends on the quality of gasket. For the production of these components we use modern materials, high-precision European equipment. Highly qualified specialists can produce door sealing rubbers of any size in accordance with the requirements of the manufacturer. Among other advantages of our products:
High accuracy of all geometric dimensions
Buy gaskets in our company you can at an affordable price, for regular customers is a system of discounts and bonuses.
The owners of rarity models of Biryusa can order the gaskets of the door according to the individual sizes. Detailed video instructions will help you to measure and assemble ready-made components. All orders are fulfilled quickly and with high accuracy of modern high-quality materials. We invite to cooperation our retailers, repair shops and service centers.