Ways to connect the radiators
Steel panel radiators have gained popularity due to their aesthetics and ease of cleaning. Flat panels are much more convenient to clean than ribbed radiators. Models are available with a different number of inlets, but they are also used for side connection of panel radiators. Today, there are 3 types (with their own subspecies) of connection.
Steel panel radiator with side connection
Panel radiators are connected in different ways:
In suburban homes often use connection of radiators from below, in apartments with central heating bimetallic models are connected by the classical way. from the side. Water supply comes from above, passes through all pipes (sections, blocks, divisions) with a drain to the common communications at the bottom.
New models are attached to the wall and pipes in different ways. Multi-sectional radiators can be expanded, panel radiators cannot, its heat output (power) is calculated in advance.
Important point! The radiator with a decorative shield absorbs 10-15% of the heat, reducing the efficiency factor. In the case of panel radiators it is vice versa. the outer structural detail is designed to warm the air. In models with double panels (front and back), the efficiency increases. They can be installed either side.
How and where to install the panel radiator
In city apartments there is a special recess under each window to place the heating unit. This is the best place for its installation. The cold air from the window slides down to the warm panel of the heater, warming up, goes up. This is how the circulation and heating of air masses and the blocking of cold streams. The radiators conceal window blinds and curtains, so it is advisable even for aesthetic reasons.
Useful tips for installing panel radiators for the private sector:
- If the room has more than 2 windows, place the radiators opposite each other to “parallel” the warm air streams for even heat distribution;
- do not install a heating circuit with sparse radiators, this is an unreasonable savings, even in an insulated building. there will be cold and warm zones, it is better to put small blocks at regular intervals;
- scheme “gravity flow” is rational, but not the best, it is recommended boiler with a pump, which will effectively run the coolant to the farthest radiator;
- it is undesirable to bend strongly heating system pipes, because it is in the bends and most often they are forgotten by sludge and rust
- in the elongated room manifolds (inputs) should not be on the end walls, in the extreme case will have to duplicate small panel radiators on a long wall, especially if it is external and poorly insulated
- Pipes under floors, ceilings and finishing materials is better to do with a minimum number of connections to minimize leaks.
Steel tubular radiator with side connection
In city apartments you sometimes need to put batteries at the front door, especially if it’s the first floor. Often the radiators are led out onto a balcony or loggia to be thermally insulated. This is the easiest way to minimize heat loss, but most often the employees of the housing office are against the suggestion to weld one more radiator on the circuit.
It is forbidden to change the scheme, the method of connection of radiators, install shut-off valves in the absence of bypasses and make other “homemade things” without notifying the management company.
Doing the self-assembly, remember that the side connection of panel radiators inlet flow must be fed from the top and outlets in the bottom hole.
Attention! The distance from the radiator to the floor, window sill and ceiling should be sufficient for the even flow of air masses. 10-15 cm, by the wall. 5-8 cm.
Installation of panel radiators with their own hands usually does not cause problems. It does not take much time, if you have experience in connecting plastic pipes with fittings and other accessories. However, it is important to meet all the requirements of the technology to avoid problems with leaks in the future. Remember also that the outer panel is quite flexible. It is easy to damage by mechanical means, and it is quite difficult to fix the defect.
The distance from the battery to the floor should be 10 to 15 cm
Vertical heating radiators with side connection
Zehnder vertical radiators side connection, model 2200 The basic element of the design of Zehnder vertical radiators 2200 is a two-tube section with a depth of 62 mm. Device sections are welded together. it gives the equipment high strength and allows to use it in centralized and autonomous heating complexes of closed type. Number of sections in the radiators varies from 2 to 30 pieces, the outer surface of the products is covered with a high-quality protective layer.
Zehnder vertical radiators with side connection, model 2180 The basic element of the Zehnder vertical radiators 2180 is a double-tube section with 62 mm depth. Sections of the device are welded together. this gives the equipment high strength and allows it to operate in centralized and autonomous heating complexes of closed type. Number of sections in the radiators varies from 2 to 30 pieces, the outer surface of products is covered with high-quality protective coating.
Zehnder vertical radiators with side connection, model 3180 Steel vertical radiators Zehnder 3180 have a classical design of their type. steel sections are welded together, the number of sections in the radiators vary from 2 to 30 pieces. Connect the devices in the side openings of ¾ inch in diameter, and you can implement a variety of piping schemes, if necessary, the cross section of the wiring can be reduced by using an adapter for ½ inch. It is recommended to install a manual or automatic air vent at the top of the device. When using a thermostatic valve it is possible to set the automatic mode to control the temperature of the heater.
Advantages of a panel radiator
The main advantage is an affordable price for panel radiators, since there are different models on the market and many manufacturers.
- You can choose the design in harmony with the style direction of the room. Some manufacturers intentionally unify products with a particular style: modern, classic;
- Comfortable regulation is offered. The level of heating is easy to control, thanks to simplified mechanical or electronic sensors;
- Almost all models provide an excellent level of heat transfer. This is achieved by the special structure of the device and the convection principle aimed at increasing the efficiency of heat output;
- In comparison with counterparts guaranteed affordable cost, because the metal models are created, thanks to the cheap and reliable steel;
- Help save energy. The device of this type is characterized by a reduced capacity, because for heating and the beginning of the process of giving off heat requires a relatively small expenditure of electricity;
- Is notable for its multifunctionality. Any product of this type can be operated as a radiator and convector;
- Reduced weight. The weight of the construction is light. Because installation is easy to perform by the owner.
In addition the product is usually sold in walking distance. You do not need to spend a lot of time looking for a suitable model.
Panel radiators with side connection
Among the modern variants of radiator batteries panel radiators occupy a fairly prominent place. They provide a good heat return both because of the large area of heat radiation and because of enhanced convection, which is achieved by using additional profiled structures (ribs). Many people are attracted by the unusual design of these radiators, which are a continuous rectangular surface of large size.
Advantages of panel radiators
Among the advantages of panel radiators are the following:
- simplicity of design increases ease of maintenance and resistance to all kinds of structural failures, which increases service life;
- the weight of such radiators is not too great, so they are easier to transport and easier to install;
- Due to the narrowness of the channels, the amount of heat carrier required is small, so panel radiators heat up quickly and create a comfortable room temperature in a short time;
- Elegant, sleek modern design;
- the price is relatively lower than that of many other types of radiators with the same functionality;
- ease of installation due to the fact that such radiators are manufactured with the possibility of connecting them in different ways: from the side or from the bottom.
Side connection features
The latter advantage will be of particular interest to residents of apartment buildings, where the usual way of connection is the side connection. Panel radiators for heating with side connection perfectly fit into the central heating system, suitable for use with both one-pipe and two-pipe systems. They are characterized by compliance with all necessary standards and requirements. Lateral connection best distributes the heat transfer medium over the radiator, so these units are more productive and provide the highest level of heat.
Efficient design
Panel radiators with side connection are made of one or more (two to four) panels, inside which are channels for the coolant. The most common material is steel. To enhance the processes of convection, manufacturers often weld additional narrow parts to the steel sheets, creating fins that better retain heat. Due to these design features, panel radiators with side connection are able to provide heating of the room with maximum effect and speed.
In our country it is very important to have a well heated living or industrial area. This is due to the peculiarities of geographical location, the heating season lasts 240-250 days on average, so you should take care of high-quality heating of your home. Modern manufacturers supply a large number of heating products, among which the steel panel radiators for heating are in particular demand. What is the popularity of these devices? The most important properties are heat output and long service life. Qualified sales consultants in our store will help you find the best steel panel radiator at affordable prices.
Steel panel radiators for heating. design features
The basic principle of construction is the welding of two metal plates. Special indentations are stamped in the production process. Dimensions range from 20 to 100 cm and lengths from 40 to 300 cm. Heat transfer performance is quite high, thanks to the increased surface area of the heating elements. This parameter provides additional comfort when using steel panel radiators.
Generally, they are most suitable for use in heating systems with low pressure. There is a perception that steel panel radiators are afraid of corrosion, but this is not true. Every year engineers develop new technologies that allow products to maintain their excellent performance at a high level. In the center of the structure there are several panels, depending on the model there can be one, two or three. Each one consists of profiles welded together on a contour. Increased heat transfer is due to the U-shaped fins in the radiator that improve convection.
Heating radiators
The radiator is one of the basic elements of heating for any room. There are several types of heating radiators: steel, aluminum, bimetallic and cast iron. For each heating system, whether it is a central (city) or a private boiler house, a different type of radiators is suitable. For private homes, aluminum sectional or steel panel radiators are best suited. These radiators are designed for low pressure and have a high heat output. They are also not destroyed by antifreeze, which can be used as a coolant in private boilers.
For urban systems bimetallic models are most suitable. The main distinguishing feature of bimetallic radiators is that they consist of two metals steel and aluminum, namely, there is a steel core inside the aluminum shell. It is thanks to this technology that the radiator is not destroyed by the aggressive alkaline environment of the central heating system.
For a sophisticated interior design in your country house, steel tubular or cast iron radiators are best suited. Steel tubular radiators have an interesting nostalgic design and a wide range of colors and can be made in almost any size. Tubular radiators can also be installed in the central heating system, but you should check with the management company parameters of the working and pressurized pressure.
Modern cast iron radiators have a unique design with the original technology of decorative casting, but because of the small thickness of the material they can be used only in country houses.
RADIATORS EXPLAINED How to fix balance bleed panel radiator How radiators work flow & return valves
If you have a high panoramic glazing in the room, you should pay attention to convectors recessed in the floor. Convector consists of steel body and copper heat exchanger. Also there is a wide range of design of decorative grilles to them. There are variants with forced convection (with built-in fan) and natural convection (without fan). This type of radiators is ideal for modern country cottages or apartments with low pressure in the heating system.
Information on all of the above radiators you can find on the pages of our website, and our specialists will help you find radiators just for you.
Steel panel radiators with side connection
Steel panel radiators have gained popularity among the users due to their light weight, high efficiency and affordable price. Among other advantages of this type of heating devices are the following:
- good heat transfer;
- easy installation;
- a wide range of different in size and design types of batteries;
- aesthetic appearance;
- Availability of models with different intercenter distance of supply and return pipes, etc.
All this allows you to choose the optimal number of devices in accordance with the initial data of the premises and ensure the most efficient heating with minimal costs for both the purchase of equipment and the flow of coolant. Buy a steel panel radiator with side connection inexpensive and fast in our online store “Plumbing Systems”.
In addition to design features such as material thickness, different number of convectors, external design and paint options, steel panel radiators may differ in the type of side connections:
- Normal lateral. supply and return pipes are located on one side edge;
- diagonal. the supply pipe is located in the upper left corner and the return pipe in the lower right corner
- saddle. the supply and return of the coolant is carried out through pipes located on the sides at the bottom of the battery.
In order to find the most suitable variant of radiators we recommend to visit our online catalog of steel panel radiators with side connection, which has not only photos of products, but also their detailed description and technical specifications. In addition, on the site of “Plumbing system” you will find current for steel panel radiators heating with side connection, which will please you with their affordability. To make an order is very simple. it’s enough to make a simple request and choose the way of payment in cash or by bank transfer (by card or by bill).
Zehnder Charleston series radiators with side connection from the official representative of “Online Climate
Zehnder is a classic version of the steel pipe radiator. This type of heater was patented by the company in 1930. Robert Zender used the principle of a motorcycle cooling system. This gave the radiator a high heat output, lightness, improved appearance and reduced production costs.
Steel radiators are well recognized in the market thanks to their longevity, practicality, high technical characteristics and aesthetics. The manufacturer is often chosen for providing a good value for money.
Zehnder. a sought-after brand in its segment. The brand was founded in Switzerland, radiators are produced in factories in Germany. The products collected the best European features: reliability, durability, compactness, economical consumption of coolant.
Among Zehnder product lines there are models of different shapes and sizes, types of connection to central heating.
Tubular radiators for heating with side connection
The tubular radiators for heating are an excellent solution for a private house, apartment or office. Among these models, steel tube radiators are especially attractive due to their many advantages:
heat transfer due to the high coefficient of thermal conductivity of steel and design features is very effective;
Tubular radiators are formed from special tubes with thin walls, bonded by laser welding. This technological approach allows you to significantly increase the service life of the product. Pipe radiators can be mounted in any part of the room in a corner, on the perimeter wall, under a low panoramic window. They are easy to install and versatile.
Features of tubular radiators for heating with side connection
One of the most effective models are side-connected tubular radiators for heating. They are easy to install in both central and individual heating systems. With the side connection of the heating system pipes can not be hidden, but such a connection provides the greatest efficiency.
In case of side connection, supply and return pipes are connected on one side of the radiator, the inlet of the coolant is at the top, and the outlet is at the bottom. Such a scheme provides the maximum heating of the heating battery and the best heat dissipation.
Practicality and versatility
Tubular heating radiators with a side connection have a high degree of practicality. Metal provides excellent technical characteristics (thermal conductivity, strength, durability), while the tubular construction allows you to give the radiator the most convenient shape and size. You can choose tubular heating radiators for your home with any number of sections. By varying the number of sections, it is possible to give the radiator the maximum size or make it extremely compact. It will provide heat for any type of room and configuration.
Advantages and disadvantages
The advantages of tubular side-connected heating radiators include numerous positive features:
Steel tubular side-connected heating radiators are reliable and durable;
Such devices have sufficient resistance to wear, water hammer, mechanical impact;
side connection is characterized by ease of installation and easy access to the pipes in case of leaks;
models with side connection distribute the coolant in the most uniform way, which increases the efficiency of heat transfer and reduces heat losses;
side-connected tubular radiators will perform equally well in a private house with an autonomous system as in an apartment with a centralized system, they are compatible with all the specific features of these types of housing.
The disadvantage of tubular heating batteries with side connection is not too aesthetic appearance of the pipes, which in the side connection remain in sight and are not masked in any way. However, this option is familiar and quite common, so those for whom efficiency and practicality are particularly important, consider these advantages preferable.
If you need a lateral supply and are interested in tubular radiators for heating, you can buy the most suitable in shape and size variant in this section of our online store.
