The glass indicator flashes on the dishwasher

The indicator flashes on the dishwasher

The blinking of one indicator, for example, a crane or brush, usually means a warning: you just need to look into the instructions and eliminate the reason for the warning.

If on the electronic board of your dishwasher suddenly all indicators began to flaunt randomly, or stopped reacting buttons on the control panel, most likely there were some problems with the electronic filling of the machine. This usually means failure of the control module, although there are random failures or the reason may be in the breakdown of some other PMM node.

If it is not possible to restore the normal operation of the PMM by a simple discharge of its settings, then there was a breakdown of some internal unit of the machine, most likely, control board: to diagnose the problem and repair or replacement of the board, it is better to stop experiments and call a qualified specialist with the necessary equipment and skills.

Although the icons on the panel of the dishwashers are now standardized, each manufacturer can have its own nuances in the behavior of indicators, so in this article we describe only the most typical cases.

Most often, our customers are concerned about the following problems:

Burning or blinking

The first and main rule: if something in the indication of the panel of the dishwasher alerted you. Look into the instructions: It is quite possible that this means one of the standard operating modes of the machine.

If any indicator is on a permanent on the panel. This is most likely normal and means an indication of the current state: for example, the brush icon lights up when the washing is launched, and goes out after its end. Another thing is when something begins to blink and the sink mode is disturbed: this may mean a breakdown of some kind of PMM node. But in any case, these are only general considerations. Behind the exact description of the behavior of indicators, you need to look into the instructions.

First, check if the protection mode from children that blocks all the buttons, except for turning off the machine, is turned on. The button flashes can also lead to the control module failure: try to dump the washing program by turning off the machine from the network for 5-10 minutes.

If this did not help, then something in the SMPMMA has broken: most likely, the control board, but problems with the door, heater, engine, programmer, sensors can lead to this effect. Only an experienced master with the necessary diagnostic equipment can accurately determine the reason.

Hansa dishwasher errors (Hansa)

Modern Hansa dishwashers are equipped with full.fledged control and self.diagnosis systems that can in real time check all the important details of the device. On models with a display, the malfunction code is displayed on the dashboard in the alphanumeric form.

There were no displays on the earlier PMM Hansa models, so the error code had to be informed by the flashing LEDs. At the same time, the list of malfunctions that the user of the machine will be informed in the operating mode was very limited: for example, the Hansa ZIM 415H model will often flash the short washing program, and when it is overflow. ECO indicator, and that’s all.

Although most of the currently manufactured models show the error code on the display, many of them still complement the output of errors with indicators. To do this, use indicators of washing programs, usually fast washing programs and ECO.

Why is My Dishwasher Flashing?

Unfortunately, the Hansa dishwasy models have a large scatter in error codes and indicators used to signal them, and we are talking not only about models removed from production, but also produced. In this article we will find as follows: first we give a detailed description of errors from their wide list (with the output of error on the display) and then briefly list the models that have other sets of error codes and ways to indicate them.

Consider also that on many models, especially without a display, not all errors will be shown in the usual mode of operation of the dishwasher: as a rule, we are talking about malfunctions with which the owners of the device will be able to cope themselves (there is no water set. Check if the tap is open, clean filters and hoses, overflow. see if the drain filter is clogged). All other codes can only be seen in the test mode launched by a specific key combination.

Hansa ZWM 446 error codes

The described set of error codes is issued on Hansa ZWM 446, Hansa ZWM 446 IEH, Hansa ZWM 446 Weh.

These models are equipped with a display, so error codes are displayed just on it in the alphanumeric format. At the same time, the error message is also accompanied by a rapid flashing of one of the indicators of the sink programs (which one, in the instructions, unfortunately, is not specified).

There are many possible reasons, you can check and eliminate some of them yourself:

  • Water does not reach the car at all: the water supply valve, a weak pressure in the water supply, a defect or blockage of the hose, the input valve, etc., is blocked.D.
  • The door is not closed or not tightly closed: electronics blocks the launch of the washing program
  • The input electroblop has broken: it will have to be replaced
  • The water level sensor (Pressostat) is faulty: Diagnosis with subsequent replacement
  • Clops in the wiring or contacts departed in circuits from the control controller to the input valve or press stratum
  • Controller’s controller failure: professional diagnosis and replacement are required if the board is faulty

Only a breakdown of one of the parts involved in the water heating procedure can lead to such an error:

  • One of the sensors is faulty. Thermal attemptor (termistor) or water level sensor (Pressostat). Diagnostics and replacement
  • Too much water flooded into the camera (for example, due to a faulty level sensor)
  • Thermistor works incorrectly: replacement
  • Cliff in the control circuit of the heating element (Ten): to ring the circuit, tighten the contacts and fix the wiring
  • Closing in the heating chain, leakage to the case: it is better to replace the heater
  • The heater burned: only change it
  • Problems with a controller controller: have to change. Call the workshop

If at the entrance to the PMM, the water pressure is too strong, the fill valve is difficult to close and, as a result, too much water can be poured into the camera

  • Call the plumbing: let it check and reduce the pressure in the water supply
  • You can cover the water tap for a little in the dishwasher yourself a little
  • Faulty of the filling valve: replacement
  • Cliff in the level of the level sensor (press start): fix the wires and fix the connectors and contacts
  • The level sensor has broken: also change
  • Fild electronics, the control board gives incorrect commands to the valve: replacement of the board

Clearly incorrect information comes from a thermal attempt, as a result, the water in the hopper either does not heat up at all, or does not heat up to a given temperature, or overheating:

Midea dishwasher errors (Midea)

MIDEA modern dishwashers are equipped with full.fledged control and self.diagnosis systems that can in real time check all the important details of the device. On models with a display, the malfunction code is displayed on the dashboard in the alphanumeric form.

There were no displays on the earlier Midea PMM models, so the error code had to be informed with the flashing LEDs. At the same time, the list of malfunctions that the user of the machine will be informed in the operating mode was very limited: for example, the Midea Zim 415H model, with a slow set of water, will often flash the short.sipping program, and with overflow. ECO indicator, and that’s all.

Although most of the currently manufactured models show the error code on the display, many of them still complement the output of errors with indicators. To do this, use indicators of washing programs, usually fast washing programs and ECO.

Unfortunately, the models of Midea dishwasy have a large scatter in error codes and indicators used to alarm about them, and we are talking not only about models removed from production, but also produced. In this article we will find as follows: first we give a detailed description of errors from their wide list (with the output of error on the display) and then briefly list the models that have other sets of error codes and ways to indicate them.

Consider also that on many models, especially without a display, not all errors will be shown in the usual mode of operation of the dishwasher: as a rule, we are talking about malfunctions with which the owners of the device will be able to cope themselves (there is no water set. Check if the tap is open, clean filters and hoses, overflow. see if the drain filter is clogged). All other codes can only be seen in the test mode launched by a specific key combination.

Error codes PMM Midea MCFD 42900

The described set of error codes is issued on dishwashers MideA MCFD 42900 G Mini, Midea MCFD 42900 or Mini, Midea MCFD 42900 BL Mini. These are very small descending dishwashers, but all models are equipped with a display, so error codes are displayed just on it in the alphanumeric format.

The error is issued if the fill valve continues to type water for more than 4 minutes. Possible reasons are diverse, some you can check and eliminate yourself:

  • Water does not enter the car: the water supply valve, a weak pressure in the water supply, a defect or blockage of the hose, the input valve, etc., is blocked.D.
  • The door is not closed or not tightly closed: the launch of the sink is blocked
  • Some problems with a flood valve or a break in its circuit: check the wiring and the valve itself
  • The water level sensor (Pressostat) is faulty or information does not receive from it: to call the circuit from the sensor to the control controller, the diagnosis of the sensor with the subsequent replacement
  • The control controller has failed: diagnostics and replacement are required if the board is faulty

The error is displayed if in 60 minutes the temperature of the water has not reached the sink specified in the program. The most likely reasons. faulty thermal attemptor or burned heating element (TEN):

  • One of the sensors is faulty. Thermal attemptor (termistor) or water level sensor (Pressostat). Diagnostics and replacement
  • Too much water flooded into the camera (for example, due to a faulty level sensor), and the heating time, of course, increased
  • Thermistor returns incorrect information about water temperature: replacement
  • Cliff in the control circuit of the heating element: ring the circuit, tighten the contacts and fix the wiring
  • Closing in the heating chain, leakage to the case: it is better to replace the heater
  • The heating element burned: only change it
  • Controller’s controller failure: you have to change. Call the workshop

The float sensor in the pallet of the car found an unacceptably high water level. The washing ends and the drain pump begins to work. Possible reasons:

  • Inspect the other places in the PMM, from where the water can flow: the flood and drain hoses, the door and its cuff, the dispenser, the internal nozzles, the camera
  • The drain pump flows: it is unlikely that it will be able to fix it, you will have to change
  • The sensor of water leakage control is faulty: diagnosis and replacement

When a signal is lost from the user integration, the sink is suspended until the connection is renewed

  • The chain between boards is broken: call, repair of wiring, strengthening contacts and connectors
  • Visualization fee is faulty: diagnosis, repair or replacement
  • Control System Coam: Call the Service

The causes of the malfunction and treatment methods are standard for problem sensors: wiring or weakened contacts, the sensor itself, the failure of the controller controller, failed. In any case, it is better to contact a specialist.

How to solve a problem?

The following is the instructions for eliminating the malfunction. But we immediately warn that to take up a number of tasks, without special skills and knowledge of the repair of PMM, do not worth. You can finally break the equipment, and this will lead either to expensive repairs or to buy a new unit.

If the control flashes the control on the panel, pay attention to the water set system. To get started, redraw the valve through which the liquid is supplied, then dismantle the flow filter, see if it is clogged and, if necessary, clean it. After that, the flood hose is removed and also cleared.

If nothing helped correct the situation, you need to inspect the intake valve. This will need to disassemble the Bosch technique housing. The valve in most brand dishes is located below. To dismantle it, you need to remove the decorative pad, disconnect all the wires and measure the resistance using a multimeter. The norm is considered to be in the range of 500-1500 Ohms. If the parameters are different. the valve needs to be changed.

What to do when the technique is incorrect to plum?

It happens that the flashing icon is associated with an incorrect connection of PMM to the drain system. In this case, it is necessary to ensure the proper removal of water. The installation of a corrugated hose on the edge of the sink using special holders can be used as a temporary measure. But this can overload the drain pump, and it will fail. Therefore, you need to connect the unit through a siphon of kitchen sink using a special adapter. It is better to entrust this task to professionals so that everything is completed according to the rules.

In the presence of a system of protection against leaks in the model, after the error with the icon of the “crane” is triggered, the water supply is stopped. Therefore, you should check the protection system. Perhaps flood the float in the pallet of the dishwasher. You also need to check for damage and leaks all hoses and nozzles. If the float is filled, you need to turn off the equipment from the power and tilt in different directions several times so that the element rises to the working position. After that, all water should be drained from the pallet and leave the equipment until it dries for about a day.

What to do if the “brush” indicator flashes?

In normal operation, the glow of this diode indicates that the washing cycle is going on. As soon as the process ends, the light is rotten. It happens that the indicator lights up at the beginning of the cycle, and somewhere in the middle ceases to glow. This is also normal.

The situation can be attributed to a malfunction in the work of technology in which in the dishwasher Bosch “Brush” flashes. At the same time, the technique may stop and no longer start until the user restarts it. What does blinking mean? In a number of situations, the reason is hidden in a short.term software failure. In this case, you need to immediately click the start button and hold it for 3 seconds, then completely de.energize the machine, wait 15 seconds and turn it on to the network again. If the problem does not disappear, then you need to determine the cause of the malfunction.

Where to look for a cause of breakdown?

So, the reboot did not help rectify the situation. Next, go to the check of the Aquastop sensor located in the pallet. It is installed only in models with a system of protection against leaks. To check the float, do the following:

  • Tilt the machine, pour water from the pallet.
  • Try to move the body in different directions so that the float falls into place.
  • Dry the aggregate body within a day. Then try to start.

There are two options for the development of the situation in the future: either the water will again be set to the pallet, and the system will work, or the problem will be solved. If the water is typed again, you need to look for a leak. To do this, it is better to call the master.

My russell hobbs dishwasher has the “glass light” flashing

The second reason for the blinking of the indicator is a inlet valve malfunction or a blocked shut.off valve. In the second case, everything is simple. the valve must be checked and open. But the broken valve will have to be changed, of course, not on its own. you need to call the master of the service center.

It happens that the indication is triggered due to the breakdowns of the control module. A professional should deal with electronics.

Bosch dishwasher flashes: reasons and what to do?

Bosch indicators blinking on the dishwasher is a warning for owners. Typically, on an electronic board, an error code is displayed, which indicates a specific problem. It remains only to open the instructions and find the value you need.

Often the reasons for blinking Bosch dishwasher are:

The malfunction can occur as a result of a malfunction of the settings, inaccurate handling of the household device, voltage jumps, natural wear, etc. P. If you find the reason for the blinking of indicators yourself, call the service center. The master provides services and areas.

Bosch Silence Plus Flashing “Tap” Light & Pump Running

Problems that can be eliminated independently

The blink of indicators on the Bosch dishwasher is a warning for owners about the malfunction. An error code that is displayed on an electronic scoreboard indicates a specific problem that arose as a result of a malfunction of the settings, inaccurate handling of a household device, breakdowns, voltage jumps or natural wear.

Transferred or clogged with a drain or flood hose

  • If the hose is curved, you need to carefully straighten it, trying not to damage it.
  • If the blocking is inside, it needs to be cleaned.
  • Water may not enter the dishwasher in the absence of pressure in the water supply. Check the pressure regulator that is located on the pipe

The crane that gives water to the dishwasher is blocked

Check the tap supplying water to the dishwasher. it should be completely open. If the crane is not completely open, then the washing cycle does not start, and the indicators on the scoreboard begin to flash due to the weak pressure of the water or its complete absence.

Impurities contained in water settled on a mesh-filter. Когда отложений слишком много, напор воды снижается и цикл мойки не запускается. As a result, the indicator indicating the error begins to flash. In the Bosch dishwasher, you can independently clean the filter from scale and lime. This is necessary:

  • Disable the device from the power supply network. Otherwise, you may hit the current.
  • Block water.
  • Unscrew the pouring hose and get a filter grid. To do this, you can use pliers.
  • Clean from scale and debris, rinse under running water, and then put in a solution of citric acid or a special tool for dissolving lime plaque. After a couple of hours, remove the filter and rinse it again.
  • Install the filter in place

When sucker at the dishwasher, the Bosch brand begins to flash indicators. The filter is located at the bottom (at the bottom) of the washing chamber and is easily removed. Pull it out and rinse it. If you do it yourself, it is difficult to use the operating instructions. Do not forget that Bosch’s drain filter needs regular preventive cleaning.

If the Bosch dishwasher was installed with errors, for example, its hoses are located below the tank level, in which case it often occurs self.sophisticated. To correct the situation, it is necessary to install the device in accordance with the requirements of the manufacturer. If you do it yourself, you can not seek the help of masters to the service center.

In addition, if you have a bosch dishwasher flashed, be sure to check the voltage in the apartment. Some indicators may burn due to low voltage. You can also try to disable the device from the power supply and turn it on again after 10-15 minutes. If this measure does not help, call the master.

Problems that require the intervention of the master

If in the Bosch dishwasher, indicators burn and flashed, and external problems are not visible, you need to seek help from the service center. Independent analysis of complex household appliances is fraught with serious consequences. So, most often indicators on the Bosch dishwasher blink for the following reasons.

The pump may break as a result of foreign objects from entering into foreign objects or combustion. If there is a blockage, the dishwasher will make a sound, as when draining water, but at the same time the liquid itself will not go anywhere. If a pump burned, the dishwasher will be silent.

On the control panel, indicators can flash and burn the “crane” icon. Some models give out error code E24 or E25. Since the details are not sold to the drain pump, when it fails it, you will have to change the spare part in full.

When the valve fails on the panel of the Bosch dishwasher panel, the indicator in the form of a “tap” will flash. Some models give out error code E14. In this case, the process of washing dishes does not begin. Rebooting the device does not help.

This happens due to the combustion of an electromagnetic coil, as a result of the valve membrane it does not open, and the water itself is not typed. To eliminate the problem, it is required to replace the filling valve.

If the Bosch dishwasher flashes or issues an E01, 20 or 24 error code, most likely, it has broken a circulation pump. This is a detail that creates the optimal pressure of water for washing dishes. If it breaks, the cycle does not start. Most often, the circulation pump is broken as a result of natural wear or from foreign objects entering.

To restore the operability of the Bosch dishwasher, you need to replace the circulation pump. This can do this a qualified master at your home.

If the Bosch dishwasher flashes and refuses to run the cycle, perhaps the wiring has occurred. This can happen as a result of unexpected stress jumps, natural wear or inaccurate treatment of technology.

To eliminate the problem, it is necessary to find the place of damage or rupture of wires. For this, the device needs to be disassembled. After the problem is detected, the master will eliminate it by twisting wires or installing new loops.

If you do not have special knowledge about the device of electricians of Bosch technique, do not try to fix it yourself. Any errors in this case can provoke a short circuit and the creation of a fire hazardous situation.

The heat exchanger in the dishwasher Bosch performs several tasks at once: protects dishes from sharp temperature drops, reduces electricity consumption, improves drying quality. It looks like a flat container filled with water and located on the side of the tank. If the part breaks or clogs, the device will stop typing water. This will cause flashing indicators in the form of a crane.

Frequent causes of breakdowns of the dishwasher Bosch

If the problems with work began after buying a machine, pay attention to the settings. Is work organized correctly? The correct connection of communications, pouring and drain hoses matters.

What breakdowns happen more often than others:

  • The technique does not start. Indicators do not burn on the panel, the system does not respond to keystrokes.
  • The defense “Aquastop” is triggered. The reason for the leakage of water in the pallet or malfunction of the float sensor.
  • Water does not merge or does not get. The point is filters, tracts. Malfunction of circulation pump or pump.
  • The program hung after the start of the sink. Holes of openings for water intake, electronic control breakdown. Luke’s malfunction is also possible.

Problems can be manifested by error code on the screen. The electronic board is associated with all nodes through wiring. If one of them does not answer, does not respond to signals, self.diagnosis starts. You will find the decryption of the code in the instructions or in the publication “Code of errors of the dishwasher Bosch”.

  • E01/F01. electronics failure, breakdown on the case of Ten.
  • E09/F09. the operation of the heating element is impaired.
  • E3/F3. water is not poured into the bunker.
  • E22/F22. Filter blockage.
  • E24/F24. E25/F25. Problems with the drain of a spent liquid.
  • E15/F15. the Aquastop system worked.
  • E27/F27. voltage surges in the network are recorded.

Some malfunctions are eliminated with your own hands. Do not rush to call the master right away, figure out the reason for the breakdown of the dishwasher. If, after excluding blockages and errors, the car does not start normal work, then start repairing.

How to repair a dishwasher yourself?

There are two characteristic problems for the Bosch PMM models. They are associated with water. Often users complain about the manifestation of the E15 code on the display. This indicates the operation of the defense “Aquastop”. But it’s not always a leakage. Perform the following actions:

  • Raise the PMM case back and look into the pallet.
  • If water really accumulated there, drain it.
  • Return the float switch to the “Off”.

Sometimes the reason for the operation is the incorrect placement of the gasket of the pouring hose. Perhaps she shifted when installing. Therefore, carry out the connection, following the user management.

The dishwasher does not turn on

You connected the car to the network, pressed the “Turning on” button, but nothing happens? The panel bulbs do not burn, no sound signals are heard. What needs to be checked:

Blinking tap Bosch dishwasher error

  • Network wire. Sometimes it is too much if during the rearrangement it is pressed by the body of the dishwasher. If you notice damage to isolation, do not do home.made twisting. This approach can lead to a fire. Replace the cord immediately.
  • Fork. The presence of melting and pogars indicates a breakdown. Install a working element.
  • Outlet. To check its performance, connect another device. Works? So the outlet is in good.

It is worth checking the network filter (capacitor). It is located near the engine. During visual inspection, they should be alerted into swollen. The detail is subject to replacement. You can buy it inexpensively in the online store.

Leave problems with electronics and control unit. The exact diagnosis is needed here, which is carried out by a multimeter.

Malfunctions of the fence and drain of water

With such problems, simple inattention should be excluded. So, it is worth checking:

  • Is a shut.off valve open. Perhaps he was accidentally blocked.
  • Is the flood hose exactly. If it is overheated, overwhelmed by an extraneous object, the water will not flow.

When installing the hose with the protection “Aquastop” you need to monitor its work. When the system is triggered, the absorbent is warmed by moisture, which is why it blocks the passage. This is a protection of one.time operation, so you need to completely change the hose.

It is important to maintain a dishwasher at least once every 1-2 weeks.

Service includes cleaning the system from garbage:

  • Cross the water supply.
  • Disconnect the hose from the body.
  • Get a filter grid.
  • Rinse it from blockage.
  • Check the inlet valve. Inspect its holes. When the garbage hits the passage, the passage is closed, which makes it difficult to move the membrane. It does not open, and the liquid does not act.

With problems with the drain, the pump is not necessarily broken. Check the details for the blockage:

  • Open the camera door.
  • Get baskets from the hopper.
  • The filter is located at the bottom.
  • Tear out and clean the part.
  • Check the pump impeller. Pieces of food, penetrating through the filter, can block its rotation.
  • Remove the water from the hole.
  • Remove the lid by pulling.
  • Put on gloves, remove blockage.

Error codes and their designations

On the display (if it is on your dishwasher), one or another error code if there is a malfunction will be displayed. You need to interpret them like this:

  • 0. there are no errors in the operation of the unit, everything is in order.
  • 1. faulty water sensor or tank filling system.
  • 2. defective heating.
  • 4. denotes an error in the process of filling the tank with water. Also on the display, this code can be indicated by the letter F.
  • 8. a failure in the temperature sensor.

If you independently look for and try to eliminate the malfunction, first of all, perform the cycle that was described above. This is the initial stage of diagnosis, the result of which will give information about what happened.

How to eliminate basic breakdowns?

If you have launched a sink cycle, but you see that the Bosch machine does not work incorrectly or stopped, it is important to keep Stihl. Most often we are talking about minor problems, especially if the unit has recently been installed. First of all, you need to check the power supply and make sure of the correct connection of the cord. With elementary errors in the connection, you may simply not work a switch.

Everything is in order with electricity? Then the problem may lie in the feloning of the hose, especially if the master forgot to blow it when I installed the dishwasher. For this reason, air bubbles are formed inside the hose that interfere with water current. You should carefully disconnect the hose and pass a little water through it, then put it back.

When interrupting the washing cycle, the machine will not type water again. This is not a breakdown. It is enough to reset the initial settings by pressing and holding the Start button. Keep the button at least three seconds. There are also BOSCH machines models, where this purpose provides the “Rezet” button, dumping all the settings to the initial level. Next, select a new cycle and start the machine again.

In case of failures in the unit, it will not hurt to check the hose located under the sink. It can be blocked or disconnected. In such cases, the machine will definitely give out a program error and fill the tank with water definitely, even if the feed is quickly resumed.

Many Bosch machines models are equipped with a small filter located inside the hose. This delays the penetration into the system of foreign objects. It is necessary to disconnect the hose and remove the internal filter, and then clean it of dirt and foreign objects if they are there. After installing the filter, start the new work cycle back.

You may not have enough water pressure to start the dishwasher and pump. In order to check this, you need to take a container with a volume of 4 liters and fill it to the maximum. If the water pressure is normal, filling the container will occur in half a minute.

The lower part of the dishwasher is equipped with a filler valve (this is the opposite side of the panel). The valve works from the mains. He can also give periodic failures in the operation of the unit. To check its condition, you need to turn off the machine from the network and remove the panel, having previously unscrewing the screws from one and on the other side.

  • Separate the screws holding the front door panel inside the Bosch machine;
  • gently pull the door panel down;
  • put her aside.

Now you need to close the door that provides access to the valve. It is equipped with two wires connecting it to the common block.

Check how reliable to fix the wires, and only then proceed to inspection of the valve itself. If it is damaged, it should simply be replaced with a new one, the main thing is to know exactly the name of the model of your unit. If you understand that you can’t do the repair of the dishwasher of the vehicle on your own, then refer to the qualified master.

Designation of signs on the dishwasher

The location of the panel depends on the type of dishwasher. If it is a built.in model, keys and indicators are located on the door of the door. Since the facade part is attached in the built.in PMM, there is no need to put the control system on the front of the door.

Separate cars are a full.fledged element of the interior, so the control panel is located on the facade part. Buttons and indicators can be signed, but often these are foreign names that you cannot break without instructions. It is more convenient when the keys are indicated by the symbols: a pan, snowflake, asterisk. Then the user can intuitively understand the values ​​of the buttons.

The variety of characters depends on the brand of the machine (“Ikea”, “ariston”, “siemens”). As well as from the number of functions of the model.

Consider the designations of the most popular brands of dishwashers.

Bosch (Bosch)

Bosch dishwashers. the most popular in the market. Manufacturers have created a wide range, a wide variety of modes and introduce new technologies. Consider the decoding of the most common characters (follow the numbering in the picture).

  • Poster with a stand (1). The symbol speaks for itself. an intensive regime (70 degrees), which allows you to wash strong pollution from pots, disgusting, pans. Duration. 115 minutes, water consumption. 21 liters.
  • Auto (cup on saucers) (2). “Automatic” mode (we can say “standard”) passes at a temperature of 45-65 degrees. Suitable for various dishes, except for products from delicate material. Opening hours. 140 minutes, consumes 19 liters.
  • ECO (economical washing) or a glass and a cup on a plate (3). “Preliminary rinse” is originally carried out, and then the program at 50 ° C. Lasts 140 minutes, spends 14 liters.
  • A glass with a cup on a stand and two arrows to the right (4). a quick cycle without primary rinsing at 45 degrees. Characteristics: 30 minutes, 10 l.
  • “Shower” from drops of water (5). “preliminary rinsing”. The program allows you to clean the dishes of food residues, prepare devices for a thorough sink. Time: 19 minutes, water: 4 l.
  • One glass. Denotes “delicate washing”, works at a temperature of 40 degrees. In this case, you can wash fragile products. Takes 75 minutes, spends 15 liters.
  • Plus and minus with the letter (6). allow you to adjust the cycle time.
  • Watch with arrows to the right (7). reduction of the duration of the regime twice (Variospeed).
  • ½ (8). half loading mode. If you have not collected dirty dishes for a full cycle, load only half with 30% saving resources.
  • Poster with rockers (9). “Intensive Wars” (Intensivezone). In the lower part, the water enters under a stronger pressure than in the upper.
  • Children’s bottle (10). Hygienic mode allows you to treat dishes at high temperature. Perfectly disinfects children’s dishes.

Start and Reset keys on the panel will help start the sink cycle or reload.

In addition, the management of the dishwasher is equipped with indicators of work. They inform the user about a particular program. We will figure out how to understand the values ​​of the bulbs on the Bosch panel.

  • Brush (1). Moika indicator.
  • End (2). ending the program.
  • Crane icon (3). water supply light.
  • Wave.shaped arrows (4). indicator of the presence or absence of salt in the ion exchanger.
  • Sunny (snowflake) (5). the presence of a rinseum in the compartment.

In dishwashers with a display, the sink modes are also equipped with bulbs. If they glow, the program is coming.

  • Icon (1)-the possibility of choosing temperature in the region of 65-75 ° C.
  • Auto (2). automatic washing.
  • Symbol “.”. temperature range from 35 to 45 degrees.
  • ECO (4). economical program.
  • A glass and a cup on a stand (5). fast washing.
  • Water jets (6). preliminary rinsing.

There is also a time indicator on the floor and on the display. In the first case, the numbers are displayed on the floor, which indicate the time before the end of the program. In the latest models there is a “ray on the floor” function. Instead of a sound signal about the end of the cycle, the machine highlights the beam.

Why the indicator blinks

It happens that the bulbs on the dishwasher begin to flash, notifying the user about the violation in the program. If the “Kne” indicator and the “End” icon flashes, there are problems when water supply. What is the reason:

Read more about this in the publication is the “Kran” indicator in the Bosch dishwasher.

HotPoint Ariston (Ariston)

Dishwasher of production “Ariston” easier in management. The designations on their panels are understandable and easily remembered by the user.

  • Indicator indicated letter (1) reports the presence of salt. The one indicated by the cross indicates the number of rinseum.
  • Poster with three lines (2). intense washing under strong water pressure. Duration. 2 h 25 min (± 15 min).
  • Poster with two stands (pan with a circle) (3). a normal sink mode. Lasts 1 h 50 min (± 10 min).
  • ECO (4). “Economical” mode. Environmental washing at 50 degrees. Time: 2 h 35 min (± 15 min).
  • The letter “r” in a circle (5)-express-soil and drying of dishes. For poorly chopped dishes. In just 25 minutes, it will clean 10 items immediately after eating.
  • Three wave.shaped lines (6). mode “soaking”. If you do not have time to start a full cycle, or dried pollution remained on the dishes, press the key 6.
  • Glasses (7). “delicate sink”. Lasts 1 hour 30 minutes (± 10 min), works at low temperature.
  • Number 8. Starting key.
  • Button “P”. selection of mode.

What do indicators mean on the Bosch panel

Depending on the type of dishwasher, the control panel is located either in the upper part of the door (built.in PMM), or on the outside (separate models). Machines with mechanical control are equipped with such indicators:

  • Brush (1) denotes the stage of the washing.
  • End (2). end of the sink.
  • The crane (3) is on. the supply of water to the system.
  • Icons in the form of arrow (4). indicate the presence or absence of salt.
  • Snowflake (star) (5). indication of the rinseum.

Models of dishes with the screen look like this:

The display may be displayed, the values ​​of which are in the instructions:

  • 1. temperature adjustment from 65 to 75 degrees.
  • 2. automatic mode (Auto).
  • 3. temperature adjustment from 35 to 45 degrees.
  • 4. an economical program at 50 ° (ECO).
  • 5 (glass with a cup). fast program at 45 ° C.
  • 6 (shower). preliminary rinse.

Also, the following designations can be found on Bosch dishwashers:

  • A children’s bottle is drawn. a hygienic mode, in which the dishes are treated with hot water.
  • Wave.shaped lines with a plus sign. additional drying.

In separate PMM models there is an indication of the end of the sink. It can be combined with a sound signal. This is a “ray on the floor”: throughout the program, the ray burns in red light, and at its end. green.

Deciphering light bulbs

Some LEDs glow constantly, others do not burn at this time. The former means the modes and programs in which the washing passes.

  • The “brush” light shines. there is a wash of the dishes.
  • Salt arrows caught fire. salt ends in the tank of the ion exchanger. If after adding it does not stop glowing, try to mix the salt in the department.

Some users turn to the master if one of the indicators constantly flashes. Most often this happens with the “crane” LED, at the same time “END” can blink. Why is this happening:

Water is not poured into the chamber. This can happen if the shut.off valve is blocked or not water in the system. Additionally, such elements are checked for the blockage and performance: a filter, filter, entrance valve.

glass, indicator, flashes, dishwasher

To check the membrane of the intake valve, it is enough to apply for the coils of the operating voltage 220 V. If the membrane opens, it means that the part is working, if not, you need a valve replacement.

There were problems in the electronic board, the contacts burned out or the simistor burned down. Each systemist is responsible for the work of one of the PMM details. As a result of a short circuit, one of them could be damaged.

The protection against the “Aquastop” leakage worked. Mechanical protection is in the intake hose. As soon as the leak occurs, a special sponge is impregnated with water and blocks water access to the system. Only a complete replacement of the hose will help.

When the “brush” indicator burns, the problem is also in the Aquastop, only the electronic type is in the pallet. Когда вода наполняет поддон, всплывает поплавок — в результате на модуль подается сигнал о протечке. But sometimes the float can stick. To get rid of the problem, tilt the body of the dishwasher from side to side.

The master can accurately determine the cause of flashing bulbs on the panel. Watch useful videos:

About the author

| Denial of responsibility | Contacts |RSS