The washing machine Becko knocks out the machine

washing, machine, becko, knocks

What to do if an RCD or difavtomat is triggered when the washing machine is connected

In accordance with the current technical standards, the wiring in the apartment should be three.wire, and the outlet networks should be equipped with differential protection. There is no need to once again tell that all this is far from always achievable. Therefore, the RCDs and differential circuit breakers in apartment distribution shields can still be seen infrequently. mainly for connecting a washing machine, which is usually located in the bathroom.

The fact is that, according to PUE standards, protection against electric receivers in the bathroom is mandatory. And, installing a washing machine in the bathroom, experts often put a separate differential protection device in the shield to connect it.

However, the situation is not at all rare when the RCD or difavtomat, to which the washing machine is connected, begins to constantly work and, which is called “spoil the nerves”.

Let’s try to deal with the possible reasons for the operation of differential protection after connecting the washing machine, as well as to determine the actions and measures with which the situation can be resolved.

The first thought that comes to mind in such a situation is the wrong connection. This primarily concerns the apparatus of differential protection. It is hardly possible to make a mistake when connecting cable cores in a socket: to trigger a differential, it would be necessary to connect a zero working and protective conductor (N and PE) together. For a two.wire line, it is likely to connect the working zero conductor and the body of the washing machine (an attempt to produce stabbing unstable by the rules). All this can cause the triggering of the RCD, but such incidents are rare, and you should not devote much time to their description.

often you have to face incorrect connection. The most typical case is when the phase is “missed” through the device, and the working zero is duplicated or simply taken directly from the general zero tire. The reason is the ignorance of the principle of operation of the RCD, according to which the entire current of the zero working and phase conductors must pass along the internal circuit of the apparatus.

If part of the current passes through the common zero tire, bypassing the apparatus of differential protection, then the RCD will perceive it as a leak and turn off the power. Therefore, by connecting the device of differential protection, it is necessary to strictly monitor the marking of the terminal clamps and follow it. The main requirement is the zero wire N, which goes to the washing machine should connect directly to the device, no additional workers of the “zeros” should be.

The malfunction of the RCD itself should not be excluded. For verification, disconnect all the outgoing wires, supply the voltage to the on the turned on the RCD (or difavtomat) and press the “Test” button. The device should disconnect only when you press the button and nothing else. If the differential protection apparatus is faulty, it is easier to replace than to repair it.

In the case when the device was serviceable, we critically evaluate the condition of the washing machine itself. If the washing machine is new, then the suspicions of it are addressed immediately. For the old washing machine, everything is possible: damage to the internal wiring, wear of insulation of the windings of the electric engine, damage to the housings of internal devices and devices.

To check the presence of internal current leaks in the washing machine itself, you can use the multimeter. Check the resistance between each plug plug and a machine body at a 20 kiloom limit. To trigger differential protection with a face value of 30 milliamps, the resistance should be 7.3 kilos or less. If the resistance exceeds this figure, then the matter is not in the washing machine.

The exception, of course, is those cases when the operation of differential protection occurs, for example, at the time of turning on the electric motor, opening the intake valve, and turning on the drain pump. At the same time, measuring the insulation resistance of a machine that is not included in the network is pointless. But this is not necessary: ​​there is no longer any doubt, and the circle of searching for faults taps to the element of the washing machine, when the problem is turned on.

It is better to present a faulty washing machine to specialists, since looking for a leakage on your own is an almost unpromising business.

If the washing machine is in good condition, then only one version remains: the electrical wiring malfunction. over, a completely new wiring may turn out to be faulty. Self.tapping screws pierced into the working zero core, hidden under the sheathing, moisture that penetrated the branch box, damaged by a knife during cleaning and tightly laid wires in the shield and the same boxes. these are the malfunctions that may occur regardless of the age of the insulation.

Search and eliminate such malfunctions is difficult enough. If we are talking about open wiring, then it must be revised throughout. It is also advisable to open the branch boxes and check whether the zero working conductor is closed to extraneous livestocks.

For hidden wiring, all this is even more complicated. It is practically possible to find only damage associated with a complete cliff of one of the cable cores. The closure of the working “zero” on nails, screws and other fasteners in the wall can only be found by many and long trials and errors.

If you do not see such a clear prospect of such work, then it will be easier to replace the cable fishing line for the trimmer. over, the operation of differential protection can be associated not only with damage to the cable, but also with the elementary aging of its isolation. This is relevant for the old aluminum wiring. For the wiring of the new, it is not excluded that the cable used during installation was counterfeit, and its isolation allows leaks without even having time to worry.

Check the wiring

The reasons for the operation of the RCD can be closed on the control, internal wiring or external power cable. The machine can go in defense and with a faulty outlet. As a rule, when the washing machine is turned on, it knocks an RCD immediately after connecting the equipment to the outlet.

Power button

A fault of the control of the washing machine is one of the reasons for the shutdown of the machine. During operation, the coating of the panel elements is oxidized and burned out. The power button can cause a short circuit due to worn contacts or moisture getting.

You can check the condition of the elements yourself. To do this, take the multimeter and call all the contacts leading to the power button. If the device shows a short circuit, then the reason for the shutdown of the electricity is found. The power button must be replaced and additionally plunder its contacts.

Socket

Washing machine. powerful power supply device (from 2 kW). The ideal option for operation is the use of a special moisture.proof outlet with a separate automatic. The use of one outlet on several household appliances should be avoided, as well as the connection to power through extension cords.

Before you start looking for malfunctions inside household appliances, it is worth checking the performance of the outlet. There can be two problems:

Before turning on the washing machine, make sure that the machine does not work due to overload. Perhaps, when launching washing, other powerful electrical appliances are used, for example, a kettle or heater. This problem is especially relevant in old houses. Disconnect all the devices and run the washing machine. If the machine is still disconnected, then you need to look for the reason further.

Try connecting another powerful household appliance to the socket. The best electric kettle. Knocked out traffic jams? In this case, you need to call an electrician to check the wiring. Make sure the washing machine itself is in good condition: connect the power cable to another outlet. If the device does not have faults, the machine should not go in defense.

Wiring

The next reason for disconnecting the machines in the apartment may be a malfunction of the internal wiring of cables in household appliances. When examining the wiring in the washing machine, we pay attention to:

  • The condition of the connecting terminals of the elements and their features.
  • The density of fastening of the wiring with the elements of the device (Ten, engine).
  • Insulation of all wires inside the device.
  • Are there any traces of moisture getting on contacts or wires.

By calling the cable by a multimeter, you can determine the sources of close. Pay attention to the places of wiring and its insulation. The causes of a malfunction of the electrocapia may be weakened fasteners of internal cables or their constant friction about the device case, as well as a short circuit.

Visually check the wiring condition. There should be no moisture on the compounds. With a short circuit, the wiring can burn, so pay attention to the traces of the carbon felts (melting) and insulation disorders. The damaged section of the cable must be soldered. Insulate the joints and check other contacts, fasteners.

Shield

The reason due to which the washing machine knocks out the machine gun can lie in the RCD itself. In practice, this is due to the use of low quality protection or inappropriate technical parameters. The machine gun in this case breaks the chain as a result of false operation, which can occur even at a slight load. For example, in the middle of the washing or spinning cycle.

Automatic protection against current is installed in the shield. Make sure that the RCD meets the requirements. For a washing machine, select an automatic machine for 10-16 and with a leak of 30 mA (10 mA in new houses).

Without skills in working with electric circuits, you should not independently repair or replace the RCD. Contact a specialist who will diagnose a machine gun, sockets and wiring.

Healthy Ten

In almost every model of the washing machine, there is a built.in heating element that allows you to launch the washing at a certain water temperature. Over time, the heater becomes unusable and can cause a disconnection of the RCD.

The indirect signs of a malfunction of the heating element are the stop of the washing machine when the water is heated. The machine may not be turned off immediately, but some time after starting the heater.

How to determine whether a malfunction of the heating element is the cause of the machine gun during washing? Need to check:

Closing and cliff are two common causes of the malfunction of the heating element in the washing machine, which can lead to a constant disconnection of the RCD. How to check is the heating?

  • Remove the back of the body of the washing machine. In Bosch, LG and most other manufacturers of household appliances, the heater is located below, under the tank.
  • Ten has three contacts to connect the wiring. Metal connective terminals. Testing will need a multimeter.
  • Check the TEN multimeter for the closure. To do this, apply one contact to the ground, and the second one is alternately to the conclusions. If there are multimeter readings, then there is a closure.
  • We determine the break, measuring the resistance between the two conclusions (the limit value of the check is 200). Normal multimeter value 20-50 Ohms. Other indicators. a sign of a cliff.

The faulty heating element must be replaced. To do this, unscrew the connecting bolt, carefully remove the heater and install a new. Do not make too much effort during repair so as not to damage other elements of the washing machine.

Charges in the washing machine

It happens that the machine is knocked out when the washing machine is turned on due to problems with the technique itself. The solution lies in finding a malfunction:

  • One of the frequent prerequisites for the failure of the machine gun is the breakdown of a tubular electric heater (heating element). This detail, like no other, is constantly exposed to the water environment and detergents. Gradually, the protective shell is corroded: moisture gets inside, a spiral itself. The result is the failure of the device and a short circuit on the network. Of course, Ten is subject to replacement.
  • The control board is faulty. Guilty, again, moisture. She gets to the control board and leads to the oxidation of contacts. The closure becomes a logical result. The degree of damage will be appreciated by the master, which will decide, replace or repair the fee.
  • The motor is faulty. Closing in this detail occurs due to its natural wear or ingress of water. Unfortunately, only replacement will definitely be needed here. such a breakdown cannot be repaired.
  • A short circuit can cause a button for turning on due to its old age and the probability of oxidation. The master can change contacts or offer to replace the button.
  • Similarly, under suspicion, there are problems with wiring and terminals inside the apparatus.

How to Replace Beko Washing Machine Pump or Unblock it

This video can help to deal with Ten:

Diagnosis of the problem

Even in an isolated case, when when turning on the washing machine it is impossible to knock out the corks, you cannot leave the incident unattended. But many owners do so: they simply go to the electric shield, put the toggle switch in place and continue to wash further. This approach is very dangerous. the next overload will simply destroy the technique. The reason must be found, but if the user has never had experience with electronics, and he does not know which side to approach the multimeter or tester, it is best to entrust this business to a professional. If the owner of the equipment is confident in his own abilities and has appropriate experience, then he will be able to discover the problem by following such a step.by.step instruction:

  • A control unit is removed from the washing machine.
  • Using the multimeter, all buttons and wires going to them are nicknamed.
  • It is important to check the network cord. you can get it after dismantling the lower panel.
  • If everything is in order with the above detail, check the network filter, which is located next to the cord. In case of a problem is detected, both the cord and the filter change.
  • After starting the device, after starting the device, the contacts, terminals, sensors and wires can affect knocking out plugs of the machine. With an already disassembled control unit, diagnostics should begin with it. But it is better to give this difficult part to test specialists. it is quite possible that you simply do not have enough experience and knowledge to notice a malfunction.
  • If the problem is not in the control unit, then you should continue moving. now we diagnose the wires moving on, and after them there are already engine, pump, heating element and other sensors and details.
  • If any burnt element is detected, it must be changed without fail (so as not to disassemble the entire car subsequently again because of it).

Such a technique has long become an indispensable assistant in everyday life. So that she can continue to wash and maintain the purity of linen, you need to pay attention to everything, even the smallest details of her work, carry out regular prevention. Such tactics will help to avoid financial costs for expensive repairs.

Knocks out traffic jams: the reason for the lack of laundry in the washing machine

So, the above options were checked and not confirmed, therefore, the reason in the device itself.

Before diagnosis or inspection, the device must be de.energized, make sure that there was no water left in the washer. Otherwise, the probability of injuries of electrical and even mechanical are high, since there are rotating nodes and units in the washing machine.

There are several reasons why it knocks out plugs, an assault rifle or meter:

  • due to damage to the plug, supplying wires;
  • as a result of the closure of the heating heater;
  • as a result of a network filter malfunction;
  • due to a faulty engine;
  • due to a faulty filter of interference;
  • as a result of the malfunction of the control button;
  • Due to damaged and groove electrical wires.

Damage to the supply cord, plug fork

Diagnostics always begins with the electric wire and fork. During operation, the cord is subject to mechanical effects: stretches, overlaps, is squeezed out. As a result of the damage, the plug and electro.stop is poorly contacted.

The damage wire is checked by a multimeter. Replacing the power cord is as follows:

  • It is necessary to de.energize the washing machine, close the entrance valve;
  • Using the hose, ensure water drain (turning the washer is strictly prohibited);
  • Remove the screws located around the perimeter, remove the panel;
  • Remove the network filter from the case by twisting the screw;
  • press the latches, remove the plastic lock, squeezing it out;
  • The electrical wire is removed inside and sideways, thereby getting access to the filter and de.energize it;
  • carefully pull the network cord out of the car;

In order to install a new cord, you need to perform these actions in the reverse order.

Malfunction of the control panel buttons

In the event that the network filter is working properly, the breakdown should be sought in the power button or control panel. Over time, the buttons can wear out and oxidize the contacts, which leads to burning and short circuit. Using a tester, you need to check the wires leading to the buttons. If the button closes in the off state, then it is faulty and needs to be replaced.

The button is used more often than the rest, so its contacts can become unusable faster than the rest. Checking the buttons on the control panel of the washing machine, you need to start with it.

You can replace the damaged button with your own hands. To do this, it is necessary to disconnect the control panel and wires going to it. After that, a faulty button is carefully extracted and a new.

Ten breakdown

The next detail in need of verification is the heater. One of the reasons that during the operation of the washing machine knocks out traffic jams is its breakdown. The main feature of the heating fault is that the washing machine does not warm the water during washing.

The heater is constantly in contact with the washing solution and water, which can eventually lead to its corroding that can cause a short circuit. The heater may also fail due to the layering of impurities on its surface and scale. Layering leads to a deterioration in heat transfer in the device, overheating and breakdown.

In order to determine the serviceability of the heater, it is necessary to conduct its visual inspection and call with the tester.

You can access the heating element by removing the back cover. In most washing machines, the heating element is located at the bottom of the tank. If the heater is located in front, you need to remove the control panel and front cover.

First of all, the heater needs to be checked for a cliff. For this, the supply wires are disconnected and the resistance is measured between them using a multimeter. The limit of the device must be set on the value of “200”. If the multimeter shows 20-50 Ohms, then there is no break in the heater. If a cliff is detected, the heater must be replaced.

To determine the closure on the case, it is necessary to measure the resistance alternately between each of the conclusions and the grounding bolt. If the result of the check is even the minimum values ​​of the multimeter, then there is a short circuit, which leads to the operation of the machine.

To replace the faulty heater, it is necessary to unscrew at 5-6 revolutions a nut located on a tightening ground bolt and drown it inside. Using the heating screw, you need to lift and carefully extract. The new heating element is installed in the reverse order. Do not tightly tighten the nut on the tightening bolt, as this can squeeze the heater from the tank.

Knocks out the machine when you turn on the old machine

We listed the reasons why the machine is knocked out at the start.

The machine is knocked out when washing

If protection devices are triggered during the washing, then in the washing machine:

  • A tubular electric heater is broken. Hard water damages the heating element. The current from the tube enters the water. there is a short circuit. Ten can be replaced.
  • Closed engine. Perhaps the winding is outdated or the junction of the drum with the bearing flows. These are Achilles heel of such brands as Samsung, LG. In any case, water enters the engine. You have to replace the engine, but sometimes it’s cheaper to buy a new washing machine.
  • Twisted wires inside the washing machine. They can also deteriorate from long.term use.

How to : remove and Clean the pump coin filter on a Beko Excellence Washing Machine.

Now you have a list of reasons that will help diagnose problems. Do not forget to turn to specialists for help. they studied for a long time and know their job. Uninterrupted light to you and good technology!

The washing machine knocks out traffic jams

An unexpected failure in the operation of the washing machine and the shutdown of light in the entire apartment is most often connected with the broken traffic jams. The washing machine knocks out traffic jams due to internal malfunctions or due to a number of other reasons. The reasons beyond the control of the machine include:

washing, machine, becko, knocks
  • Newly purchased household appliances were launched. If you have a problem with knocking out plugs, it is worthwhile to suspect the malfunctions in the wiring or in improperly selected equipment to protect the mains.
  • At the same time, several electrical appliances work in the apartment. The turned on the electric stove and the erasing machine can simultaneously trigger traffic jams due to too much load on the electric network.
  • The cord in the device is damaged, the malfunction is visible with the naked look. If a fork or cord is “short”, it is advisable to refuse the use of equipment before fixing the problem.

If traffic jams are knocked out for other reasons, the problem lies precisely in the breakdown of the machine. It is advisable to immediately disconnect the device from the electric network, the further use of a faulty unit is dangerous for people living in the apartment and for the electric network of the whole house.

Common reasons for knocking out a machine gun

The washing machine knocks out the machine gun due to internal breakdowns, the problem can also be associated with the accumulation of condensate on the internal details. In the case of condensate, it is enough to leave the device for 1-2 days at rest. The problem with condensate occurs extremely rarely, most often the knocked out machine gun is triggered by breakdowns in the following nodes:

  • Ten. The part in the typewriter is constantly under load, experiences a negative effect on the part of water, detergents, microparticles of the washed things, as a result, with frequent use of household appliances, the detail fails. Solving the problem. replacing a faulty spare part.
  • Managing fee. Contacts on the board are oxidized due to constant contact with the humid environment. The malfunction is eliminated either with the help of repairs or by completely replacing the module, it all depends on the degree of damage.
  • Engine. It fails due to natural wear or as a result of water leaks, causes a closure. The engine is not subject to repair in such cases, it is necessary to replace.
  • Turning buttons. Most often, the start buttons are pressed on the typewriter, as a result, the contacts wear out and cause a short circuit in the mains.

If the washing machine knocks out the RCD, it should by no means continue to use it. When closed, the current passes to the case, as a result, you can get a fatal lesion of the current. Also, breakdowns can provoke a fire.

If you have sufficient qualifications to eliminate problems, purchase spare parts from Samodelkin: there is everything you need. Delive through the PVZ nearby in the house.

Causes of malfunctions in the very washing machine

Когда выполнен осмотр электрической проводки и выявленные неполадки в ней ликвидированы, однако, УЗО опять срабатывает, стало быть, неисправности возникли в машинке. Before inspection or diagnosis, the unit must be de.energized, make sure that there is no water in the typewriter. Otherwise, the threat of electrical and possibly mechanical injuries is high, since the car has rotating units and nodes.

There are a number of factors why traffic jams, counter or RCD are knocked out:

Damage to the plug, cable power cable

Diagnosis invariably begins with an electric wire and fork. When used, the cable is subjected to mechanical stress: it is transmitted, overlapped, pulled. Due to the malfunction, the plug and an electric outlet have poor contact. The cable for malfunctions is tested by amperevattmeter.

A short circuit of a thermoelectric heater (Ten)

Due to the low quality of water and domestic chemistry, the thermoelectric heater is “eaten”, various outsiders and scale are poured, the transmission of thermal energy becomes worse, the thermoelectric heater overheats. this is how it happens to suck out. As a result, the electric meter and traffic jams are knocked out. To diagnose the heater, disconnect the electric power cable and the resistance is measured by means of amperevattmeter, setting the maximum value on the “200” mark. In normal condition, the resistance should fluctuate from 20 to 50 Ohms.

Sometimes the thermoelectric heater is closed to the case. To weed out such a factor, take turns measuring the conclusions and grounding screws for resistance. Even an insignificant amperevattmeter indicator reports soaking, and this is a factor in the shutdown device shutdown.

The failure of the filter to suppress interference from the supply network

The filter is required in order to stabilize the electrical voltage. Network differences make the knot unusable, when the washing machine is turned on, the RCD and traffic jam is knocked out. In such a situation, the filter requires replacement.

The fact that the network filter for suppressing interference from the supply network was in the hair clipping, the elements of melting on contacts say. The filter is tested, nicknamed the incoming and outlet wiring amperetwattmeter. In certain brands of cars, an electric cable is mounted in the filter, which equally required to change.

Electricifier malfunction

The reason for the short circuit of the electric motor wiring is not excluded with long.term use of the unit or violation of the integrity of the hose, tank. The contacts of the electric motor and the surface of the washing machine are alternately nickname. In addition, the traffic jam or a protective shutdown device is knocked out due to the wear of the electric motor brushes.

The failure of the control button and contacts

The electric button is operated most often, in connection with this, the inspection should begin with its verification. During the initial examination, you can notice the contacts that oxidized and worn out. Amperevttetmeter is checked by wires and contacts leading to the control panel, electric motor, thermoelectric heater, pump and other units.

Damaged and duffed electric wires

The full of electric wires is usually formed in an inaccessible place of the washing machine. Когда агрегат вибрирует в процессе слива воды либо отжима, электрические провода трутся о корпус, спустя определенный отрезок времени изоляция перетирается. Electric circuit on the case and becomes a consequence of the fact that the machine is triggered. The sections of damage to the electric wire are determined visually: on the insulating layer there is sooty, darkened zones of melting.

❌ BEKO Washing machine WMB 61042 ❌

These areas need soldering and secondary insulation.

Elimination tips

Here we will tell you what to do in each certain case.

Replacing the power cable

If for some reason the power cable was spoiled, it must be changed. The replacement of the power cable is carried out in this way:

  • You need to turn off the power of the washing machine, block the input valve;
  • by means of a hose, creating conditions for draining water (overturning the unit is strictly prohibited);
  • The screws located on the contour should unscrew, remove the panel;
  • extract a filter from the housing to suppress interference from the supply network by turning the screw;
  • crush the latches, remove the plastic stop, squeezing it out;
  • Put the electric wire inside and to the side, thus getting access to the filter and turn off the power from it;
  • Gently get a network cable from the machine;

beko white wash small loud

To put a new cable, it is necessary to carry out these actions in the reverse order.

Replacement of the heating element

As a rule, the thermoelectric heater has to be changed. How to correctly fulfill it?

  • Dismantle the rear or front panel (it all depends on the location of the heating element).
  • Scroll the ground screw for several revolutions.
  • Carefully pick up the thermoelectric heater and get.
  • Reproduce all actions in the reverse sequence, only with a new element.
washing, machine, becko, knocks

Should not tighten the nut too tight. You can connect a test machine only after it is entirely assembled.

Replacing a filter to suppress interference from a supply network

If the filter is out of order to suppress interference from the supply network, it must be changed. Replace the element simple: disconnect the wiring and turn out the mount. A new part is mounted in the reverse sequence.

Repair of the electric motor

As mentioned above, another factor, why the machine is knocked out. the failure of the electric motor. He is able to break for a number of reasons:

To find what exactly failed, it is possible by calling the contacts of the electric motor and the entire surface of the unit. If a breakdown is detected, an electric engine is replaced, if possible, they eliminate the breakdown. The place of course will certainly eliminate. The brushes are dismantled, removing contacts from the terminals. After the installation of new brushes, the electric motor pulley is turned with your hands. If they are installed correctly, the engine will not make noise loudly.

Replacing and cleaning the control button and contacts

The procedure for cleaning and replacing the control button includes the following steps.

  • Dismantle the top panel, which is held on 2 self-tapping screws located on the rear panel. Make sure the machine is disconnected from the mains, the water supply valve is closed.
  • Disconnect the terminals and wires of power. As a rule, all terminals have the protection of various sizes. We advise you to take photographs of all steps taken.
  • Unscrew the control module and carefully tighten in the direction of the rear panel of the machine, so unhindered access to the buttons will appear.
  • At the final stage, buttons are cleaned or replaced.

We also advise you to pay attention to the state of management. Are there any darkening, burned fuses, bloated caps of capacitors. The arrangement of the washing machine is carried out in the reverse order.

It must be said that to knock out the machine when starting a washing machine or washing in different modifications for a variety of reasons. For the most part, this is a malfunction in electrical wiring, however, at times one of the elements is out of order. When it is possible, they should be repaired, with a different development of events, you will have to visit the store, choose the necessary details and replace them. It will be more reliable when the master is doing this.

Finally, I would like to warn: when the machine is knocked out when the machine is launched, the threat of an electric shock is high. this is dangerous! In addition, even insignificant violations in the electrical wiring of the unit or in an electric network lead to fire.

About the author

| Denial of responsibility | Contacts |RSS