To what temperature the sole of the iron heats up

Iron temperature adjustment: maximum, by points

Heating the sole of the iron must correspond to the material of the smooth clothing. With an insufficiently high temperature, you will have to spend a lot of time and effort on obtaining the desired result. If the heating is too high, it will ruin delicate fabrics.

In the old days, cast.iron irons not only did not have a temperature regulator, they could not even heat themselves. To stroke, I had to fall asleep in them for coals or put an iron on a preheated furnace. In early electric models, the heater worked constantly. Therefore, after reaching a suitable temperature, the housewives had to turn off the equipment from the network.

Modern ironing bodies provide controls for setting the temperature regime. As a rule, a rotary wheel is installed on the housing, but mobile handles, sensory screens or automation can also be installed for control.

To make the use of technology convenient, a system of graphic designation of the modes was invented. The temperature of the iron by points on the wheel is determined:

  • Heating the soles no more than 110 ° C. Suitable for delicate fabrics.
  • An increase in temperature to 150 ° C, a steam ironing function is available. This mode is optimal for polyester, wool and similar materials.
  • Maximum heating necessary for flax, cotton, drape, twid. The temperature of the sole in this mode reaches 200 ° C, due to which steam processing of the fabric is facilitated, and as a result, the effectiveness of ironing increases.

If you are not sure of choosing a mode, then look at the label attached to the clothes. On it, the manufacturer indicates all the necessary information on the care of the product, including ironing rules (temperature, the possibility of using steam processing).

Maximum and minimum temperature of the iron

The above values ​​at points are maximum for each mode. The nominal temperature in each of them is 95, 130 and 175 degrees, respectively. The minimum for one point is 75, for two and three. 100 and 145. All these indicators are medium for the surface of the sole, and in its different zones, the temperature may vary 5-10 degrees.

How to iron a shirt with OptimalTemp

Some models are equipped with displays, which display the temperature with an accuracy of a degree. But this is excessive functionality, because a small error in heating is not able to worsen ironing or turn into a spoiled thing.

temperature, sole, iron, heats

Pay attention to the activity indicator. If it burns, then the iron heats up. When the bulb goes out, the maximum temperature for a given mode was achieved, and you can start ironing. If the sole cools too much, the iron will turn on again.

How to set the temperature properly depending on the type of fabric

For each fabric, there is an optimal temperature regime of ironing, which is indicated by the manufacturer on the label. For ironing to always be as effective as possible, it is important to be able to decipher these icons.

The product is allowed to iron at any temperature.
Ironing at high temperatures up to 200 ° C.
It is found on products made of polyester, polyacrylonitric tissues. The maximum temperature is 140 ° C.
Such an icon suggests that the product is made of delicate fabric, which must be ironed at a temperature not exceeding 130 ° C.
The temperature should not exceed 110 ° C. It is found on things from polyamide, acetate, nylon, viscose.
You can neither be ironed nor processed with steam.
Can be stroked, but steaming cannot be used.

How to iron things from various fabrics can be found out from

Temperature modes of the iron in degrees

In the heat.regulated devices, the “points” corresponds to a certain temperature (data in the table)

Heating the household iron within the sole may vary by 10 ° C.

To how many degrees the iron heats up as much as possible

For fabrics that are most poorly ironed, it is necessary to use the maximum heating temperature of the iron in degrees equal to 205 ° C. In this case, the heating rate will depend on the type of material from which the sole of the iron is made, and the power of the electrical appliance.

Heating rate depending on the sole material

  • Aluminum. Heating occurs very quickly, cooling down, but the material is short.lived. Solid elements on clothes can leave scratches on it, into which the borneled particles of fabric are clogged.
  • Of stainless steel. It heats up quickly, slides well on the surface, differs with durability. Disadvantage. a large weight of the device.
  • Ceramics. Such a coating is applied on a metal base. It slides perfectly, allows you to fade the fabric in hard.to.reach places, does not catch your clothes. Heating and cooling down longer. Ceramics retains heat, so even in the off state, the iron is 8-10 minutes. It remains hot. The disadvantage is the fragility of ceramics, the susceptibility of chips and damage. To extend the service life, manufacturers use cermet.
  • Teflon. reliably protects clothes from suction, but does not last long. The teflon surface does not glide on the fabric, making it difficult to iron.
  • Sapphire. a specially developed alloy that gives the sole special strength. He conducts heat well.
  • Titan. rarely used in the production of household ironing. Metal will quickly warm up and cool for a long time. Surface strength is not inferior to steel.

The maximum temperatures in different models may vary, so before choosing the mode, you need to familiarize yourself with the instructions.

If there is only one heating mode in the iron, there is no function of spraying and vaporization, the temperature of the sole of the iron will be 115 ° C (± 10).

The irons with a drip system is slightly hot. about 155 ° C.

Electric appliances with the possibility of steam processing reach a temperature of 175-205 ° C.

The impact of the power of the electrical appliance

The speed of heating the surface depends on the power of the iron, the possibility of supplying the “cloud” of steam, the speed of cooling the sole directly during ironing.

To how many degrees the iron heats up as much as possible

For fabrics that are more difficult to iron, it is necessary to use the maximum heating temperature of the iron in degrees equal to 205 ° C. In this case, the heating rate will depend on the type of material from which the sole of the iron is made, and the power of the electrical appliance.

Heating rate depending on the sole material

  • Aluminum. Heating occurs very quickly, and cooling occurs, but the material is short.lived. Solid elements on clothes can leave scratches on it, in which fabric fabric particles are clogged.
  • Made of stainless steel. It heats up quickly, glides well over the surface and is durable. Disadvantage. the large weight of the device.
  • Ceramic. This coating is applied to the metal base. Slides perfectly, allows you to iron the fabric in hard.to.reach places, does not stick to clothes. Heating and cooling take more time. Ceramics retains heat, so even in the turned off state, the iron will last 8-10 minutes, remains hot. The disadvantage is the fragility of ceramics, a tendency to chips and damage. To extend the service life, manufacturers use cermet.
  • Teflon. reliably protects clothes from suction, but does not serve long. The Teflon surface does not glide on the fabric, which makes it difficult to iron.
  • Sapphire is a specially developed alloy that gives the sole additional strength. He conducts heat well.
  • Titanium is rarely used in the manufacture of household ironing. Metal will quickly heat up and cool for a long time. Surface strength is not inferior to steel.

The maximum temperatures in different models may differ, so before choosing a mode you should familiarize yourself with the instructions.

If there is only one heating mode in the iron, the spray function and steam is not provided, the temperature of the sole of the iron will be 115 ° C (± 10).

Electric appliances with the possibility of ferry treatment reach a temperature of 175-205 ° C.

The impact of the power of the electrical appliance

The speed of heating the surface, the ability to create a “cloud” steam, the speed of cooling the sole directly during ironing depend on the power of the iron.

In domestic models, power varies from 800 to 2200 watts. Models not equipped with a thermostat and moisturizer have lower power, within 400 watts. It is much more difficult to iron them, they heat up slower, cool quickly.

Advice! For home use, an iron with a capacity of 1,500 to 2200 watts is suitable. For lovers of stroke a large number of things with maximum comfort, models are suitable close to 2700-2800 watts, but this must be ensured that the wiring withstands such a voltage and not include several electrical appliances at the same time.

Long.term professional ironing, for example, in laundry or dry cleaning, will require the purchase of a more expensive and powerful device, from 2800 watts. Heating in such models occurs as quickly as possible, and the steam blow is extremely powerful (about 230 g / min).

The minimum temperature of the iron

To choose the lowest temperature, select the silk ironing mode (one point). Minimum ironing temperature. 75 ° C.

In the ironing irons without a thermostat, the heating temperature is about 115 ° C. Since it is impossible to choose a delicate processing mode for the product, it is necessary to start ironing from the wrong side, moisturizing the fabric.

When aligning things that cannot be stroked, even a mode set on one stitch can ruin it. For safe tissue processing, you need:

  • Urate, placing a thing between two layers of fabric: from below. dry, at the top. wet.
  • exposed steam;
  • Moisten from a spray gun and hang for leveling;

Advice! Before processing the steam, make sure that particles of rust and drops of water that can leave stripes do not come out of the nozzles. Removable plate-pumping prevents dirt from getting.

The temperature of the steam in the iron

The steam helps to moisturize clothes and greatly facilitates its smoothing, but for especially wrinkled areas, a “portion of the couple” is used. The range depends on the power of the iron.

In domestic models, the force of the steam is about 20-25 g / min. professional technology allows you to work with steam supplied with an intensity of 160 g / min. In this case, the temperature of the steam reaches 160-210 ° C, depending on the characteristics of the model.

How to find out the temperature of the iron

The easiest way to find out the temperature of the iron is by points. However, it happens that with delicate ironing, the thing “burns”, or on the maximum setting, the sole remains not hot. Perhaps the reason in the broken thermostat. You can check the temperature of the heating of the iron using high.temperature thermometers. It is enough to buy a digital or mechanical device that allows you to measure the temperature up to 300 ° C, because in the iron there is no higher temperature. The cost of meters 200 is more expensive. infrared pyrometers (from 1000), which allow you to measure the temperature without direct contact with the object. This device is useful for measuring liquids, food, electric heaters and other items.

There are also “popular” testing methods:

  • Sprinkle with an iron and wait for hissing. This means that the temperature is above 100 ° C.
  • Natural iron wool. If the villi becomes dry and brittle, the temperature approaches 105 ° C, and if an unpleasant smell of burned hair appears, heating reached 120.

In order not to risk your favorite things, it is important to know exactly what temperature the plate has reached. It is better to experiment, but to buy a device with a thermostat, follow the instructions for use, study the labels on the clothes before ironing. If you suspect a malfunction, measure T with a special thermometer and repair the electrical appliance in accordance with the warranty coupon.

Maximum and minimum heating temperature

In order to stroke clothes, the iron needs to be heated, at the same time its sole will heat up. The temperature of the iron can be different, when it is selected, the type of fabric and volume of things for ironing is taken into account. Each model of this device differs in its characteristics and functionality. An important parameter of any electric iron is its power.

What do the numbers or points indicated on the electrical panel mean

The power of the iron affects the temperature of the heating of its sole, as well as the heating rate. In modern home models, power is usually in the range of 1400-1900 watts (1.4-1.9 kW). The most common power is considered to be 1400-1500 W (1.4-1.5 kW), which is quite suitable for ironing jeans or shirts.

On the iron panel with dots or numbers, the temperature range is usually marked.

One point or number 1 on the panel indicates:

Two points or number 2 shows the temperature:

Three points or digits 3 on the panel indicate the temperature:

What material the soles are made of

For the result of the ironing to be perfect, the sole of any electric veug should be warmed up evenly. This ability is possessed by devices with a ceramic surface. There are also irons with a metal (aluminum, steel, cast.iron) sole. They are distinguished by good gliding, good heat capacity, strength.

Most modern irons have built.in thermal controllers, tubular electric heaters (heater) and signal lamps. expensive models are equipped with steam.

However, all this functionality on the heating temperature of the sole of the electro.veug does not have a practical effect.

So in order to determine what temperature to set for ironing things, it is better to focus on the above ranges.

About optimal temperature conditions

For each type of fabric, there are its own ironing modes that allow you to bring clothes to a decent look without harming it. All models of irons are now equipped with the temperature control function by type of fabric. And for this, knowledge is necessary at what temperature should be stroked this or that thing.

Advice. Almost every thing has special shortcuts with a note about how much this product can be stroked.

temperature, sole, iron, heats

If there are no shortcuts, but the material from which this thing is made can be known, you can use the general recommendations. Knowing the maximum and minimum heating temperature of the sole of the iron (205 and 78, respectively), having the concept of the material of the product, you can easily choose the optimal mode for ironing.

How to choose the right iron for home

It is important when choosing this home assistant to pay attention to his design and various functional additions:

  • The working plane of the iron, in contact with the fabric during ironing, is called the sole. Its characteristics largely determine the functionality of this electrical device. Therefore, it is important to pay attention to this when buying. The sole can be made of aluminum, steel or cermet. The cost of the electrical appliance depends on the material of the sole.
  • The function of moisturizing the ferry, which can help quickly and well iron any fabric. It is important to evaluate the volume of the water tank, which can range from 200 to 400 ml.
  • Water sprayers are needed to moisturize things before ironing in cases where they can hardly process them with steam. over, it is necessary to use only cleaned water so as not to leave dirty spots on clothes.
  • The function “for forgetting” when using a special sensor will help protect both clothes and the iron itself (after 20-30 seconds of downtime in a horizontal position or several minutes of inaction in an upright position, the iron automatically turns off).

It is also necessary to pay attention to the consumption of electricity, that is, the consumed power of the iron, which can significantly affect the speed of warming up and the process of pair formation:

  • Models of ironing with a capacity of less than 1,500 watts (1.5 kilowatts) are usually small in size and belong to convenient road models. There is no vaporization function in them.
  • Electric vests with a capacity of 1500-2000 W (1.5-2 kW) are suitable for a small number of things requiring iron ironing.
  • Choose irons with a capacity of more than 2000 watts (2 kW) should be if you constantly stroke many things at once. With the built.in vaporization function, the speed and quality of ironing will be significantly higher. Such models are more related to professional ironing appliances than home.

Before you buy the most powerful iron, find out in advance how much voltage is in your electric network and whether it corresponds to this power.

If necessary, purchase an electric iron for daily use with small volumes of clothing, it is worth choosing models with a power of 1.4. 1.5 kW. Do not also forget about the conformity of the power and capabilities of the mains of your home. It is very important to consider how much the electricity iron consumes, and what additional functionality does it have.

Iron Temperature: Deciphering the Designation, Selection of the correct mode

For each type of fabric, a certain ironing mode is established, with which you can bring the product in a proper appearance without damaging it. Experienced housewives know that the temperature of the iron is adjustable, and the desired degree of heating of the sole is set, taking into account the type of material from which the thing is sewn, as well as the texture of the applied pattern (if any).

The temperature regime regulation function allows you to set the switch to one of the three provisions. The modern iron, like Soviet, has 3 designations: one, two and three points.

Each of them determines the temperature of heating the working surface of the device. In some cases, the modes are indicated not by points, but by type of fabric.

To make it easier to navigate, some manufacturers next to the points indicate the type of material:

Some models have a little below the initial value the inscription “NYLON”. The switch set in this position limits the heating temperature of the sole to a possible minimum so that it can be processed from synthetic threads.

Minimum and maximum heating temperature

The work surface of the iron is made from:

The minimum amount of time to achieve a given temperature regime requires aluminum sole. Castle and steel work surfaces are quickly heated by the quickly. Devices with soles made of cermet and ceramics gain temperature slower, and they need more time to cool.

Important! When buying an iron, it is worth considering not only speed, but also uniform heating of the sole. Both of these indicators affect the quality and ease of ironing.

The speed at which the minimum and maximum temperature is achieved depends on:

  • set mode;
  • electrical appliance power;
  • the material from which the working surface of the device is made;
  • the presence or absence of a vaporization system.

The average value of the heating speed of the iron varies from three to eight minutes. If you measure the temperature of the sole, then we can draw the following conclusions:

  • The highest heating rate has devices with a capacity of 2.5 kW;
  • If the power of the device is in the range from 0.8 to 1.3 kW, then the heating will be slow.

The power of the iron must correspond to the capabilities and technical condition of the mains to which it will be connected.

Selection of the correct ironing mode by icons on clothes

The maximum possible heating of the device is 205 degrees, and the minimum value is 110. This is enough to stroke the product from any fabric without damaging it.

Before proceeding with the processing of a thing, you should study its label. It should have one of these icons.

Important! This information allows you to understand which mode should be set on an iron to iron a particular product.

What temperature should your flat / curling iron be at?

Sometimes there is no shortcut with care information. In such cases, you should focus on the type of fabric from which it is sewn.

  • Linen. The flax product before ironing should be turned inside out and ironed at a temperature regime of 180-200 degrees. To achieve ideal results, it is necessary not only to set the above value on the regulator, but also slightly moisturize the material. Do not be afraid to press the electrical appliance and use steam. If there is cotton in the composition, along with flax, then heating the sole of the iron above 180 degrees is not recommended. You should also take into account the presence of decorative elements made of synthetic materials, which are allowed to be processed only from the wrong side.
  • Wool. Woolen things do not tolerate high temperatures, so the regulator should be set at a value at which the sole heats up to 100-120 degrees.
  • Cotton. Cotton fabrics should be ironed at a temperature regime of 170–180 degrees. It is advisable to moisturize the material to get rid of the folds. You can use the function of steaming.
  • Silk. Things sewed from delicate fabrics are stroking very carefully. The temperature of more than 60–80 degrees and steaming are unacceptable.
  • Viscose. Maximum temperature regime. 120 degrees. You can moderately process a ferry thing.
  • Knitwear. It is recommended to iron products from this material on minimum and average temperature regime. So that the thing does not deform, the function of vertical steaming should be used.
  • Nylon. Nylon fabric is quite whimsical, it is not recommended to iron it. If creases appeared on the product, then before processing it with an iron, you need to install the regulator in position 60–80 degrees, no more.

If the type of fabric cannot be determined, then it is worth choosing a sparing mode and gradually increase the temperature until the folds begin to be smoothed out.

Why Are Your Radiators Getting Hot When the Heating Is Off?

  • Iron Bosch TDA 3024010 on Yandex Market
  • PHILIPS GC2990/20 Powerlife iron on Yandex Market
  • Braun Texstyle 7 TS735TP iron on Yandex Market
  • PHILIPS GC3675/30 EasySpeed ​​Advanced iron on Yandex Market
  • Rowenta DW 5135D1 iron on Yandex Market

The speed of heating the iron

The speed with which the surface is heated not only on the selected regime, sole material, but also on the power of the electrical appliance, as well as on the presence or absence of a steam formation system, and if it is, then from its performance. The average values ​​of the heating rate of modern iron from 3 to 8 minutes. The highest heating rate has powerful devices from 2.5 kW, such devices are designed for professional ironing. For a small family, a device with a capacity of 1.5 kW to 2 kW is suitable with a lower heating rate, and the most slow are road options with a capacity of 0.8 kW to 1.3 kW.

Attention: the power of the device connected to the network must correspond to the state of the network and its capabilities. In case of non.compliance with the capabilities of the network and power of the electrical device, the connection is unacceptable!

What depends on boiling in home and other conditions?

For example, for water in normal conditions (760 mm. RT. Art.) this indicator is 100C. On the other hand, it changes easily. In addition, various impurities dissolved in water dissolved in water. In most cases, these are salts. natural, giving stiffness, or artificially added, for example, food welded.

Mark in 100C. given for distilled H2O in normal conditions. Standardly used water. from water supply, stream, lakes, wells, etc. D in reality it is an aqueous solution of various salts. Therefore, the temperature of its boiling is slightly higher than the reference value.

On significant hills, due to the fall of atmospheric pressure, boiling begins earlier. However, the process of brewing. as a way of cooking. does not become faster, but, on the contrary, increases and becomes difficult.

Every 300 meters of rise from the sea level reduce the boiling point by one degree. Climbers know that high in the mountains boiler boils at 85-90s and even below.

The opposite effect occurs in natural lowlands and with an increase in atmospheric pressure. the boiling point exceeds several familiar indicator.

Maximum and minimum heating temperature

Testing of Electro.Tyugov. 2012

Testing of electrical irons in the program “Control Procurement” has been conducted for 5 years now and the history of the examination of their quality is interesting to consider in its development.

For this time “on the carpet”, that is, on the ironing board, irons are called:

Irons presented in comparative tests. 2012

As you can see, all recognizable “faces”. Well.known tests of past years. The TEFAL iron and the Vitek iron became 4 times, the Panasonic iron, the Bosch iron and the Philips iron. in the third, the Moulinex iron. in the second.

So we have an amazing opportunity to trace how the quality of electric vehicles change in time. And what?

Let’s start with the “gaming”. That the brands promise us?

All irons are armed with fuccation “spray”, which allows to aimed to direct water to separate folds. Everything, but not Panasonic, promise a steam blow of different intensity. But the Panasonic iron was distinguished by the presence of a system of protection from scale, while the rest can boast of only a self.cleaning system. All are equipped with a steam regulator. But if everyone has that at 3-4 levels, then the Vitek iron offers the consumer as much as 13! With the exception of Tefal, all the ironing is a function of vertical steaming. And the pointed “nimble” nose of the Philips iron promises to make the most intimate corners of the things of a particularly difficult cut accessible to iron.

In a word, who is more at the auction of generous promises? And the consumer has no choice but to believe the word to manufacturers and advertising. In the store, after all, no matter how much the iron is in your hands, most of the promised functions cannot be checked. They checked. Tests! And what happened?

The average temperature on the surface of the sole of the iron for various positions of the thermostat

According to GOST 307.1-95 (70-110) City. C-synthetics (100-150) City C-Wool (140-200) City. C. cotton/flax

Conclusion: The average values ​​of the heating temperatures of the sole of the iron, Philips, Tefal exceed the temperatures set by GOST 307.1-95 for appropriate modes.

Evaluation of ease of use

Four women and one man conventional designations of assessments (points) participated in the assessment: (4,1-5.0) excellent; (3.1-4.0) good; (2.1-3.0) satisfactory; (1.1-2.0) mediocre; (0.1-1.0) unsatisfactory

The tested electric vests vary by mass: over several tests, the Bosch iron is recognized as the easiest. The most difficult was the PHILIPS electric. Once again we remind. that for modern ironing, massiveness is not a “plus”, but “minus”, since high.quality ironing is not due to the weight of the iron, but due to properly selected temperature and effective vaporization.

Panasonic iron and Vitek iron were completely unsuitable for operation. Due to the banal leak. Water does not go into the promised steam, but in puddles formed under the iron in front of the eyes of a discouraged user. In the dry language of the protocol, “Panasonic and Vitek irons were removed from testing due to water flowing from a leaky tank”. But we are talking about completely new irons.

But the iron Bosch and the iron Moulinexv was pleasantly surprised. Recall that the irons of Bosch and Moulinex were removed from previous tests of social quality monitoring due to the same “incontinence”. Now, a year later, neither one nor the other is suffering. Manufacturers, having reacted to “television signals”, eliminated defects that caused leakage.

The Moulinex iron also turned out to be the most convenient, and so that the only one was awarded the evaluation “excellent”. And the best showed himself in the test of the intensity of soaring. The holder of the longest power cord. 246 cm. But this is already the taste of the consumer. The Moulinex iron stumbled later, getting excited above the measure.

  • Paring intensity is measured in g/min
  • The standard deviation is indicated in brackets (g/min)
  • Irons t.m. Vitek and Panasonic in the intensity of soaring did not participate due to water leakage, which makes them unsuitable for operation

“We got excited”. Beyond measure!

During subsequent tests, it was found that the temperature of the soles of the soles of the Tefal iron. Philips and Moulinex exceeds the maximum permissible values ​​that are established by the requirements of regulatory documentation. Without suspecting this, users can easily spoil their clothes with tan, otherwise burn!

As a result of any serious Комментарии и мнения владельцев, the testers did not find only Bosch ironing. In addition, the Bosch iron turned out to be the easiest “on the rise”. By the aggregate of assessments, the iron bosch and was recognized as the leader of the test.

Testing of Electro.Tyugov. 2012

Testing of electrical irons in the program “Control Procurement” has been conducted for 5 years now and the history of the examination of their quality is interesting to consider in its development.

For this time “on the carpet”, that is, on the ironing board, irons are called:

Irons presented in comparative tests. 2012

As you can see, all recognizable “faces”. Well.known tests of past years. The TEFAL iron and the Vitek iron became 4 times, the Panasonic iron, the Bosch iron and the Philips iron. in the third, the Moulinex iron. in the second.

So we have an amazing opportunity to trace how the quality of electric vehicles change in time. And what?

Let’s start with the “gaming”. That the brands promise us?

All irons are armed with fuccation “spray”, which allows to aimed to direct water to separate folds. Everything, but not Panasonic, promise a steam blow of different intensity. But the Panasonic iron was distinguished by the presence of a system of protection from scale, while the rest can boast of only a self.cleaning system. All are equipped with a steam regulator. But if everyone has that at 3-4 levels, then the Vitek iron offers the consumer as much as 13! With the exception of Tefal, all the ironing is a function of vertical steaming. And the pointed “nimble” nose of the Philips iron promises to make the most intimate corners of the things of a particularly difficult cut accessible to iron.

Selection of the correct ironing mode by icons on clothes

The maximum possible heating of the device is 205 degrees, and the minimum value is 110. This is enough to stroke the product from any fabric without damaging it.

Before proceeding with the processing of a thing, you should study its label. It should have one of these icons.

Important! This information allows you to understand which mode should be set on an iron to iron a particular product.

Sometimes there is no shortcut with care information. In such cases, you should focus on the type of fabric from which it is sewn.

  • Linen. The flax product before ironing should be turned inside out and ironed at a temperature regime of 180-200 degrees. To achieve ideal results, it is necessary not only to set the above value on the regulator, but also slightly moisturize the material. Do not be afraid to press the electrical appliance and use steam. If there is cotton in the composition, along with flax, then heating the sole of the iron above 180 degrees is not recommended. You should also take into account the presence of decorative elements made of synthetic materials, which are allowed to be processed only from the wrong side.
  • Wool. Woolen things do not tolerate high temperatures, so the regulator should be set at a value at which the sole heats up to 100-120 degrees.
  • Cotton. Cotton fabrics should be ironed at a temperature regime of 170–180 degrees. It is advisable to moisturize the material to get rid of the folds. You can use the function of steaming.
  • Silk. Things sewed from delicate fabrics are stroking very carefully. The temperature of more than 60–80 degrees and steaming are unacceptable.
  • Viscose. Maximum temperature regime. 120 degrees. You can moderately process a ferry thing.
  • Knitwear. It is recommended to iron products from this material on minimum and average temperature regime. So that the thing does not deform, the function of vertical steaming should be used.
  • Nylon. Nylon fabric is quite whimsical, it is not recommended to iron it. If creases appeared on the product, then before processing it with an iron, you need to install the regulator in position 60–80 degrees, no more.

If the type of fabric cannot be determined, then it is worth choosing a sparing mode and gradually increase the temperature until the folds begin to be smoothed out.

Recommendations for choosing ironing temperature for various fabrics

There is often a situation when a shortcut with recommendations for caring for things is missing. In these cases, practical advice will come in handy.

The thing must be first turned out and ironed at a temperature of 180-200 ° C. The best result is achieved when the fabric is wet. During ironing, do not be afraid to press on the iron and use the steaming.

If the thing has an admixture of cotton, then above 180 ° C the iron should not be heated. It is worth considering that decorative elements (for example, embroidery) are often made of synthetic materials, so they need to be ironed only from the inside.

What to do if matter is very dense and is not ironed properly? Such things are ironed additionally on the front side, at the same temperature, but necessarily through gauze. If the product is stolen, then the temperature must be reduced by 10. 20 degrees.

Wool

The coat does not take high temperatures, so the optimal regime for it is 100. 120 ° C. This applies to woven wool, and knitting things are better not to iron at all. If you really want to iron your favorite sweater, then you need to do this from the inside, without pressing the iron, so as not to stretch the material. Drampo coat is stroked at 140.170 ° C, necessarily with steaming.

Cotton

This material must be ironed at a temperature of 170. 180 degrees. Like flax, it is better to process cotton at a time when it is not completely dry, or to previously moisturize from the spray gun. You can use steaming.

This is a very delicate material, which should be ironed as neatly as possible. It does not tolerate the temperature above 60. 80 ° C, as well as steaming. If there is a need to iron through the fabric, then it is worth using thin cotton, but not gauze (ugly traces may remain on a silk product). When processing through the fabric, the temperature can be increased by 20 ° C.

Viscose

The maximum temperature is 120 ° C, it is allowed to steam slightly.

Iron not heating up? Here’s how you can fix it.

Knitwear

The temperature regime is medium or minimal. In order to avoid tissue stretching, knitwear is better to steam instead of ironing in an upright position.

To how many degrees the iron heats up as much as possible

For fabrics that are most poorly ironed, it is necessary to use the maximum heating temperature of the iron in degrees equal to 205 ° C. In this case, the heating rate will depend on the type of material from which the sole of the iron is made, and the power of the electrical appliance.

Heating rate depending on the sole material

  • Aluminum. Heating occurs very quickly, cooling down, but the material is short.lived. Solid elements on clothes can leave scratches on it, into which the borneled particles of fabric are clogged.
  • Of stainless steel. It heats up quickly, slides well on the surface, differs with durability. Disadvantage. a large weight of the device.
  • Ceramics. Such a coating is applied on a metal base. It slides perfectly, allows you to fade the fabric in hard.to.reach places, does not catch your clothes. Heating and cooling down longer. Ceramics retains heat, so even in the off state, the iron is 8-10 minutes. It remains hot. The disadvantage is the fragility of ceramics, the susceptibility of chips and damage. To extend the service life, manufacturers use cermet.
  • Teflon. reliably protects clothes from suction, but does not last long. The teflon surface does not glide on the fabric, making it difficult to iron.
  • Sapphire. a specially developed alloy that gives the sole special strength. He conducts heat well.
  • Titan. rarely used in the production of household ironing. Metal will quickly warm up and cool for a long time. Surface strength is not inferior to steel.

The maximum temperatures in different models may vary, so before choosing the mode, you need to familiarize yourself with the instructions.

If there is only one heating mode in the iron, there is no function of spraying and vaporization, the temperature of the sole of the iron will be 115 ° C (± 10).

The irons with a drip system is slightly hot. about 155 ° C.

Electric appliances with the possibility of steam processing reach a temperature of 175-205 ° C.

The impact of the power of the electrical appliance

The speed of heating the surface depends on the power of the iron, the possibility of supplying the “cloud” of steam, the speed of cooling the sole directly during ironing.

In household models, power ranges from 800 to 2200 watts. Models that are not equipped with a thermostat and moisturizer have a lower power. within 400 watts. It is much more difficult to iron them, they heat up more slowly, quickly cool.

Advice! For use in everyday life, an iron with a capacity of 1,500 to 2200 watts is suitable. Fans of stroke a large number of things with maximum comfort are suitable for models with a power close to 2700-2800 watts, but it is worth making sure that the wiring will withstand such voltages, and do not include several electrical appliances at the same time.

Professional multi.hour ironing, for example, in laundry or dry cleaning, will require the acquisition of a more expensive and powerful device. from 2800 W. Heating in such models occurs as quickly as possible, and the steam blow is extremely powerful (about 230 g/min).

The minimum temperature of the iron

To select the lowest temperature, you need to select the SILK ironing mode (one point). The minimum ironing temperature is 75 ° C.

In the ironing irons without a thermostat, the heating temperature is about 115 ° C. Since it is impossible to choose a delicate mode of processing the product, you should start ironing from the wrong side, moisturizing the fabric.

When aligning a thing that is not subject to ironing, even a mode set to one point can ruin it. For safe tissue processing, you need:

  • moisturize it from the spray gun and hang it for leveling;
  • influence steam;
  • iron, placing a thing between two layers of fabric: from below. dry, from above. wet.

Advice! Before steaming, it must be made that particles of rust and drops of water that can leave stains do not come out of the snot. The removable nozzle on the sole of the iron will help prevent pollution.

The temperature of the steam in the iron

The steam helps to moisturize the thing and greatly facilitates the alignment of the fabric, but for especially crumpled areas, a “steam blow” is used. The supply intensity depends on the power of the iron.

In household models, steam exposure force is about 20-25 g/min. professional technology allows you to influence a ferry coming with an intensity of 160 g/min. In this case, the temperature of the steam reaches 160-210 ° C, depending on the characteristics of the model.

About optimal temperature conditions

For each type of fabric, there are its own ironing modes that allow you to bring clothes to a decent look without harming it. All models of irons are now equipped with the temperature control function by type of fabric. And for this, knowledge is necessary at what temperature should be stroked this or that thing.

If there are no shortcuts, but the material from which this thing is made can be known, you can use the general recommendations. Knowing the maximum and minimum heating temperature of the sole of the iron (205 and 78, respectively), having the concept of the material of the product, you can easily choose the optimal mode for ironing.

Selection of the correct ironing mode by icons on clothes

The maximum possible heating of the device is 205 degrees, and the minimum value is 110. This is enough to stroke the product from any fabric without damaging it.

Before proceeding with the processing of a thing, you should To study her label

It should have one of these icons.

Important! This information allows you to understand which mode should be set on an iron to iron a particular product.

Sometimes there is no shortcut with care information. In such cases, you should focus on the type of fabric from which it is sewn.

  • Linen. The flax product before ironing should be turned inside out and ironed at a temperature regime of 180-200 degrees. To achieve ideal results, it is necessary not only to set the above value on the regulator, but also Slightly moisturize the material. Do not be afraid to press the electrical appliance and use steam. If there is cotton in the composition, along with flax, then heating the sole of the iron above 180 degrees is not recommended. You should also take into account the presence of decorative elements made of synthetic materials, which are allowed to be processed only from the wrong side.
  • Wool. Woolen things Do not tolerate high temperatures, Therefore, the regulator must be set at a value at which the sole heats up to 100-120 degrees.
  • Cotton. Cotton fabrics should be ironed at temperature regime 170–180 degrees. It is advisable to moisturize the material to get rid of the folds. You can use the function of steaming.
  • Silk. Things sewed from delicate fabrics are stroking very carefully. The temperature of more than 60–80 degrees and steaming are unacceptable.
  • Viscose. Maximum temperature regime. 120 degrees. You can moderately process a ferry thing.
  • Knitwear. It is recommended to iron products from this materialand minimal and average temperature regime. So that the thing does not deform, the function of vertical steaming should be used.
  • Nylon. Nylon fabric is quite whimsical, It is not recommended to iron it. If creases appeared on the product, then before processing it with an iron, you need to install the regulator in position 60–80 degrees, no more.

Each fabric has its own ironing and washing mode, which allows you to bring the thing into proper form without damaging it. Modern irons significantly facilitate the ironing process, because they have the functions of regulating temperature by tissue types, but the modern housewife simply needs to know at what temperature a certain thing is stroked so as not to spoil it.

About the author

| Denial of responsibility | Contacts |RSS