Devimat heating mats
Walking barefoot on a warm floor when there is a snowstorm outside is great! But what if you do not want to spend a lot of time and effort to install a floor heating system, tinker with screed? Install Devimat heating mats. Underfloor heating Devimat is excellent for thin, repairable floors and does not raise the floor. Suitable for installation under ceramic tiles. Installation is extremely simple. a heating cable is secured in a loop on a thin self-adhesive mesh that can be easily cut with scissors.
- Store is a 7 minute walk from the Sokol metro.
- We have only official products.
- We deliver your purchase, not only in Moscow, but also throughout Russia.
Guarantee20 years
Why do not need a foil backing?
Underfloor heating is essentially a heated cement-sand board that is located above the floor slab and directly under the floor covering. The heat flow from such a heater is divided into two parts: the flow going up is a useful part, which heats the floor and the flow going down. this part heats the ceiling of the neighbor from below and is a loss. The ratio of these flows determines the efficiency of the system, and it is certainly desirable that it be as large as possible. This is achieved by increasing the thermal resistance in the layers below the cable, i.e. by using a higher thermal conductivity.е. by installation of thermal insulation. The task of calculating heat fluxes for each specific case is solved quite simply.
The general conclusions here are as follows:
In cases where there is a heated room under the ceiling on which the floor heating is installed, the heat loss downstairs is relatively small and amounts to 15-20% for typical conditions.
If there is a non-heated room under the ceiling (a cold basement under the first floor slab), the losses are much higher and amount to 50-70%.
If there is “street” under the ceiling (for example, a warm floor on the balcony or loggia), the losses are up to 95-98%.
It is clear that in the last two cases the use of thermal insulation is absolutely necessary. As for the first, the installation of thermal insulation is also useful, but to noticeably reduce heat loss, its thickness should be at least 25-30 mm. Above the heat insulating layer must be mechanically strong (and therefore quite thick) screed. As a result, the rise of the floor becomes unacceptable for most customers.
There is another common misconception about the effectiveness of foil as a “heat reflective layer” in a mass of cement-sand screed. There can only be a reflection effect of thermal radiation when the majority of the heat is transferred through the radiative mechanism. Meanwhile, the vast majority of building materials and in particular cement-sand screed are opaque to infrared radiation. The heat inside the screed is transmitted solely by thermal conductivity, so we can’t talk about the effects of reflection.
Electric underfloor heating
Double-core heating mat DEVIcomfort (DTIR-150)
Shielded double core heating mat with one cold end
DEVI. Electrical Heating Systems
A thermostat is required for correct operation!
Thickness 4.5 mm, double core Specific power: 135 / 150 W/m2 Maximum temperature: 90 C° For installation without thick cement screed for thin floors
Double core heating mat Devimat (DTIF-150)
Extremely slim double conductor heating mat with Teflon high-temperature insulation with one cold end.
Thermostat required for correct functioning!
Thickness 3,5 mm, 2-wire, with Teflon insulation Power density: 135 / 150 W/m2 Maximum temperature: 90 C° Installation without thick cement screed for thin floors
Devimat dual core heating mat (DTIF-200)
Ultra-thin, two-core heating mat with Teflon high-temperature insulation with one cold end.
Thermostat required for correct function!
Thickness 3.5. 4 mm, two-wire, Teflon-insulated Specific wattage: 180 / 200 W/m2 Maximum temperature: 110 C° Installation in rooms with higher heat losses
DEVIheat single core heating mat (DSVF-150)
Ultra-thin shielded single-core heating mat with two cold ends
A thermostat is required for correct operation!
Thickness 3 mm, single core Specific power: 135/150 W/m2 Maximum temperature: 90° C For installation without thick cement screed for thin floors
Devi floor heating system generates several times more heat than the central heating system and distributes it evenly throughout the room.
One of the main parts of the underfloor heating system. heating mat. The industry leader Devi (Denmark) produces high quality double-wire heating mats Devimat, which are characterized by small thickness. wire diameter not exceeding 4.5 mm. and high durability.
Devimat underfloor heating is absolutely fireproof. shielded heating cable has inner Teflon and outer PVC insulation.
Installation of Devimat mats simple enough: as compared to single-core, double strand mat does not require additional drilling, installation of technological channels for electrical wiring, as heating cable in it does not need to return back to the thermostat from which it was started. This is very convenient in small rooms, such as bathrooms and toilets.
Thanks to the small thickness of the mat, Devimat is ideal for premises where it is impossible to make a screed, having raised the floor level up to 5 cm. Most often the heating mats are installed under the tile, into the tile adhesive, but the placement on the concrete is also possible.
On the back side of Devimat is placed a self-adhesive mesh, through which the heating cloth is firmly fixed on the surface, and the marking allows you to accurately cut the mat to the required size.
Adhesive composition of the grid was specially designed to order the company, which managed to significantly increase the adhesion of the surfaces, surpassing in this parameter all existing analogues.
After installation, the “cold” leads mat and a special sensor through a thermostat is connected to the network. Devimat mats have a wide power range from 75 to 1800 watts.
Devi gives a 10-year warranty on heating mats and their service life when installed in concrete is more than fifty years.
Underfloor heating mats
Installing underfloor heating under a tile is a simple task if you choose modern heating mats. This system allows you to install underfloor heating in the tile adhesive layer without any screed. This means that all work can be done in the shortest possible time and without extra cost. Heating mats:
- They practically do not raise the floor level and are therefore ideal for rooms with low ceilings;
- Can be installed on top of old floors, which greatly reduces installation time and therefore costs;
- have a wide range of lengths and sizes, can be easily installed in areas of complex configuration.
Special heating mat for laying “dry” directly under wood, laminate and carpeting. Easy installation with factory-assembled connectors. Power 100 W/sqm.м. Dimensions: from 1 to 5 m 2 Availability: On order
Single-core heating mat with a wattage of 150W/sqm.2.5 mm thick. Veria. is a new quality product from Denmark, manufactured on modern equipment by European quality standards.
Double core heating mat of the Danish brand Veria. Power 150 W/sq.m, thickness 3.5 mm. Double-wire structure and continuous screen reduces electromagnetic radiation to virtually zero.
Deciphering of marking of heating floors Devi
Knowing the symbols of these materials can greatly facilitate the choice and reduce the time when buying. Let us consider what designations of mats and cables exist and how they are deciphered.
DTIF. this designation indicates the use of a two-core shielded cable with one “cold” end. For example, DEVImat DTIF 200T, where:
Before you buy an underfloor heating, you need to know the product names
Let’s look at another example, the DEVIflex DTIF18T. Here:
- DTIR is the designation for a flame-retardant two-core cable without a lead sheath;
- DSVF. designation of single-core fire-resistant shielded cable with one core (two “cold” ends);
- DTIP is a low-power cable with 2 wires, used on thin screed or in apartments with wooden floors.
Mats cannot be laid in this way
Devi tile underfloor heating mats
All trademarks belong to their owners. No part of this site may be reproduced in any form without the consent of the copyright owner.
This website is for information purposes only and under no circumstances does the information materials and posted on the website constitute a public offer as defined by the provisions of Article 437 of the Civil Code
The of goods on the site are given without shipping costs. The cost of delivery within the Moscow Ring Road depends on the order amount:
Outside the Moscow Ring Road and the specified cost is added at a rate of 45 per 1 km from the Moscow Ring Road.
Delivery means delivery of goods to the entrance of the customer. It is possible to pick up directly in the apartment. Check the lift from the manager.
For some goods a reduced / increased cost of delivery within the Moscow Ring Road, it can be seen in the product card under the price.
It is possible to pick up the goods from the storage room by prior arrangement with the manager.
Warehouse address: m. Moscow, Kozhukhovskaya str. Yuzhnoportovaya str. 32с11
The warehouse is open Mon-Fri 10:00. 18:00, Sat 10:30. 15:00.
Self delivery is available: Mon-Fri: 10:00. 20:00, Sat 10:30. 15:00.
Dear customers, in our showroom not all the goods you can find on our site are demonstrated. Goods in stock are in a package which can be opened only when buying goods to check its integrity and completeness.
- the cost of the shipping company, which is calculated by each shipping company individually, based on the volume, weight of the shipment and delivery conditions;
- Santehnica delivery costs.Delivery to the terminal of the transport company and the registration of goods. 750
- Read more about delivery in regions here
Delivery is usually made the next day after receiving the order. Delivery service operates from Monday to Saturday from 09:30 to 18:30.
We pay your attention, that next day delivery is not always possible, because.к. depends on the workload of the delivery service. Orders received earlier have priority in terms of delivery. To obtain the goods the next day it is desirable to place an order before 14-00 of the current day. Delivery on the day of the order is possible by agreement with the manager of Santehnica.ru.
You can use the service “Lift to the floor“. This service is chargeable. Our staff will pick up your order directly to your apartment, regardless of whether there is an elevator in your house.
Attention! Delivery of the goods is carried out by default up to the entrance. Order the service of lifting the goods at the time of agreeing the order.
The “walk-up” cost is calculated as follows: the amount for each floor lifted from the “no elevator” column is added to the “freight elevator” column. For example, lifting a wall-hung toilet to the third floor without an elevator costs 350, which adds up to: 250 2 floors at 50
The cost of a single-floor lift (or bringing it up to the elevator/stairwell) is calculated as a freight elevator ride, at the rates listed below
Below is a standard calculation of the cost depending on the product group. You can always confirm the final cost of the lift to the floor with our manager.
Pros of electric underfloor heating
Can be used everywhere. They are suitable for both private and multi-family houses. You only need to coordinate the installation of underfloor heating with the building management company. Long service life. If all installation rules are followed, the heating system will last at least 50 years. Easy assembly. The system can be laid independently, to approach the process responsibly and make all the necessary calculations in advance. One disadvantage: the electric bill will increase. Let’s understand what is a system of electric floor heating.
Resistance heating floors are of two types: Cable. a wire that is laid on the floor in rows. It is sold with a thermostat and a sensor for adjusting the temperature of the floor. To heat the room, the system is connected to the network, the current flows through the wire strands and gradually heats the shell. The heat goes from the shell to the flooring.
Devi underfloor heating under tiles
One of the main advantages of electric underfloor heating is the possibility of using any floor covering. Reliable Devi underfloor heating is suitable for tiling, laminate, parquet. Most often such systems are laid just under the tile, because it is convenient and practical.
Features arrangement of underfloor heating under tiles
Consumers who choose such equipment for their premises will be useful for the following information:
- One of three types of cables can be used for installation under tiles. Single-core DSIG cable is suitable for outdoor areas such as balconies and porches. Double-core DTIP cable is used for stairs. For indoors, an improved twin-core DTIE cable with bio-insulation is the best choice.
- DEVImat heating mats are supplemented with reinforced mesh, and have a thickness not exceeding 3 mm. When installing does not use insulation, fastening is carried out at the expense of an adhesive base.
- The choice of equipment for underfloor heating is determined by the characteristics of the room, as well as the presence or absence of other heat sources. Under-floor heating foils and mats are suitable if an underfloor heating system is to supplement the central heating. When the floor heating is used as the only heating device, it is worth using powerful cables that allow temperature adjustment. 100 Watt is enough for a living-room or bedroom, 120 Watt is enough for a bathroom. In rooms with a large area, a power of 150 W is appropriate.
Advantages of Devi underfloor heating
Electric underfloor heating under the tile Devi has unique performance characteristics that make it a universal option. Among them:
- safety (tile glue serves as grounding, eliminating short circuits);
- ease of installation due to flexibility and low weight of the elements;
- gradual heating and uniform heat distribution;
- Little or no noise during operation;
- long service life no maintenance required for 20 years.
- Designing a scheme of underfloor heating, taking into account the location of windows, doors, sanitary ware, appliances (eg a fridge), and the presence or absence of central heating.
- Preparing holes for the installation box, leveling the floor.
- Installation of elements of the underfloor heating system (installation of mats, cables, anchoring the mesh reinforcement).
- Conducting a test resistance measurement for safety purposes.
- The laying of tiles (made after the mortar dries out completely).
- The first launch of the system is carried out not earlier than 30-40 days after completion of installation work.
Buy electric underfloor heating under the tile Devi with delivery in Moscow you can in our online store. Equipment from the official dealer quality assurance and competitive prices.
Floor heating Devi (Devi) the official dealer’s website | Buy floor heating Devi (Devi)
Underfloor heating Devi: how to calculate, choose and install correctly
One of the main tasks in creating a heating system is to maintain a uniform temperature throughout the room. The work of only one radiator will not be able to fulfill this condition, because the warm air will rise. The best way to solve this problem is to install Devi floor heating.
Danish company Devi is among the largest world manufacturers of modern heating systems. Underfloor heating is an effective option for underfloor heating under almost any type of coating and with any structure, while being quite economical and easy to install. Devi products are known all over the world thanks to its high quality and performance properties. Floor heating Devi was among the leaders of sales also due to the company’s slogan. use only environmentally friendly materials in the production.
Advantages of Devi heating floors
DEVI is the largest manufacturer of electric cable heating systems in Europe. Uniform distribution of air. Those, who established the warm floor Devi in the apartment or in any other premises, know. the warmth is really on the bottom and on the top. Wide range of applications. Can be used both in the residential sector (apartments, summer houses, country houses), and in office buildings.
Eco-friendliness. The absence of convection in the floor heating system of Devi significantly reduces the dustiness of the room, which is important for children and people suffering from allergic diseases, as well as chronic syndromes of the bronchopulmonary system.
Energy saving. It would be strange if a European company did not care about energy saving. Accurate control systems are used in Devi heating floors, which can save up to 20 percent of energy by lowering air temperature by 1-2 degrees.
Can be installed with almost any floor covering. Yes, because Devi electric floor heating can be used not only with traditional materials (carpet, laminate, tile, etc.), but also with other materials (carpeting, laminate, etc.). ), but even with concrete floors!
Long life. Manufacturers officially claim a service life of 80 years!
The possibility of realizing your design fantasies. After all, if you exclude the installation of traditional heaters, replacing them with underfloor heating system, you can save space in the apartment, using it to install interior items, or just to increase the area, and since a large proportion of apartments in our country is small, this is a significant plus.
We can talk endlessly about the merits of Devi underfloor heating, but you can get a complete picture of these electric heating systems only if you try them in use.
