Water supply hose of washing machine what thread

Connection to the washing machine what a thread. Connecting a washing machine to the water supply. The use of a passage valve

The acquisition of the Automatic washing machine involves the implementation of the necessary installation work to connect to communications: water supply, sewage and electric network. Installation and connection of the unit can be entrusted to the master or performed independently. How to install a crane for a washing machine and connect the unit by ensuring its uninterrupted operation, we offer to find out from this article.

The main task of the tap for the washing machine is to block the water supply in the case of the repair of the hydraulic unit, its rearrangement or removal from the previous room. At the same time, he will not influence the passage of water to the mixer, ensuring uninterrupted water supply.

On sale there are cranes for a washing machine made of silumin and brass. It is preferable to choose brass taps. Although they cost an order of magnitude more expensive than silumin analogues, they are able to withstand constant loads and regularly serve for more than a dozen years.

When purchasing a tee, it is also worth paying attention to the type of thread (internal or external), as well as the diameter of the pipes involved during installation.

Division on the tee should have an external thread d = 1/2 inches.

But in any case, after installing the crane in the breaks between the operation of the unit, it is necessary to keep closed. Since the water pressure is able to break the hose in a matter of seconds. The consequences of this can be very deplorable: in 10-15 minutes the water will flood the apartment and rush to the neighbors from below. Washing machines are equipped with hoses for the supply and drainage of water, as well as an electric cord. In addition to buying a three.pass crane for a washing machine, you will also be required:

  • additional hoses (in case the length of the hose in the kit with the unit is not enough for installation);
  • additional filter of rough cleaning;
  • siphon with a discharge for draining;
  • a rosette protected from moisture;
  • FUM tape;
  • Divorce key.

Connecting a washing machine

When choosing a place of installation, you should be guided by being able to connect the unit to communications without special troubles and enough space for its comfortable operation.

Unpacking the unit

When removing the packaging from the machine, you should check for the absence of scratches and dents, as well as make sure the integrity of the drain hose and the supply cord.

With the help of a wrench, the transport bolts are unscrewed, first lifting one, and then the other edge of the machine.

The maximum is unscrewed by adjusting legs. Then, on the rear panel, transportation screws with spacers are unscrewed, and the remaining holes are covered with plugs. Only after that they install the unit, withstanding the distance between the rear wall and the wall of the room of 5 cm. Having set the hydraulic unit, using the level, level its position in order to reduce vibration during the squeezing process.

Connection to the water supply

First of all, with the help of an introductory valve, the water is blocked in the apartment, and the remains are drained by opening the taps.

How to connect to the water supply your automatic washing machine

It’s good if a contour with a ball crane is provided. In this case, the connection is reduced only to the installation of the hose. If this is not equipped, it is necessary to insert into the pipe and install the tee for connecting with a flexible license plate.

To bring water, you need to use a pipe through which cold water passes.

With the help of a divorce key, a tee is wound on a pipe, sealing it with a fum tape or linen. After that, a flexible eyeliner is mounted and a hose is fixed from the washing machine, the right end of which is equipped with a plastic nut. A rude cleaning filter is installed on the bent end of the same hose and connected to the machine.

water, supply, hose, washing, machine, thread

Tip: The nuts on the hose itself should be tightened with your hand, without making additional efforts: the tightness of the connection is ensured due to the rubber gasket.

Connection to the sewage system

The set to the machines is plastic hooks to fix the drain hose and drain into the sink or bath. If this method does not suit, the connection of the drain can be executed into the sewer system. To do this, the hose is removed directly to the pipe through the siphon. a plastic knee with a special drive on which the tip of the hose is fixed. The drain hose at the output is lifted to a height of about 60 cm and fixed using special mounts.

Important: the withdrawal is placed above the curved area of ​​the knee in order to provide a connection with the atmosphere and prevent the occurrence of a “siphon effect”, in which the unit simultaneously begins to fill and drain the water.

Electric network

Since in most cases, washing machines are installed in rooms with high humidity, it is better to use moisture.proof outlets to connect them to connect. It will not be superfluous in the outlet and the presence of a grounding conductor.

To do this, the pipe is cut off at the right level and the thread is performed or the connection made of the pipe and flexible wiring is disassembled, setting the connecting fittings into the gap.

It is better to perform wiring for connecting a washing machine through an RCD with a leakage current within 30ma.

Having completed the connection of all communications, it remains only to carry out a trial washing. During the first washing, it is important to monitor the location of the hose to supply water from the water supply to the machine, as well as a drain hose. The water supply tap to the washing machine should not vibrate and make extraneous sounds. If the leak is detected, after the end of the washing process, the connection points and the fit of the gaskets should be checked once again.

Trinch tower for connecting a washing machine

Having bought a new washing machine or moving to another apartment, you will have to connect it to communications. Even if there are no conclusions, then they can be mounted independently, without resorting to the help of a plumbing. After arranging the conclusions, additional details will be needed. So that you will definitely have to buy a special crane-trotter to. We will figure out the types of devices and their features.

DIY connection connection

To correctly connect the washing machine with your own hands, first you need to choose the most optimal location. The washing machine is connected through a regular outlet.

In some kitchen rooms, the equipment is installed under a working countertop, where it is quite problematic to get located near the arranged sockets.

Thus, it is more appropriate to arrange the equipment one and a half meters from the surface of the table (connecting device with a fuse) with a switch, connect with a ring chain and mount the wiring using a hard wire with a cross.sectional diameter of the closing device to the outlet located behind the machine.

Connection of the water supply hose

Usually, when installing a water supply system, during the repair of an apartment or house, the installation sites of household units are in advance, the work of which is connected using water. These are primarily washing and dishwashers. In these places, an experienced installer necessarily sets special taps for connection. They subsequently connect special hoses for water supply.

The usual dimension of the taps ½ and ¾ with external thread. This dimension also has hose nuts. Connection is carried out with a closed crane.

Before fastening the tube, you must make sure that there are sealing gaskets. It happens that they are included and require installation. In some cases, they are simply lost during transportation. After making sure there are gaskets, you can connect a water hose.

Usually from the side of the machine connection to the fitting, the tube has a M-shaped form under 90 degrees for convenient connection. Holding the tube from twisting, it is necessary to wind the nuts on the connection crane and on the fitting. The sequence in this case does not play the role. The main thing is that when installing the unit, the pipe does not twist and not bend. With the opening of the water crane, the connection can be considered complete.

Materials and tools for connecting to water supply and sewage

The need for certain materials when installing and connecting washing machines to the sewage system and water supply is determined, first of all, the location of the unit and the availability of the designated objects. In some cases, it is necessary to go to obviously more significant costs so that it is subsequently convenient to use household appliances for many years.

If you provide for the laying of additional branches from the water supply in the stroke, you will need a sufficiently powerful corner corner grinder with a saw disk by concrete. You can use a hammer and a locksmith chisel to dry out concrete.

A pipe without joints is laid in the stroob to ensure its durable operation without leakage. Otherwise, if the flow occurs, the restoration of the functionality of the pipe will be associated with a large volume of work to search and eliminate the malfunction.

To connect to the water supply network, a tee with a cutting tap is usually used, and to install it in place. a set of wools or a universal divorce key. All threaded joints are compacted by bags or fum tape.

The installation of outdoor layering is associated with the fastening of the pipe to the wall, for this you will need an electric drill and a drill on concrete. Plastic dowels are installed in drilled holes, fastening is carried out by screws of the corresponding size.

When installing washing machines, the main requirement is the horizontal location of the upper cover with respect to the floor. For the exact installation of the washing, the construction level is used, the adjustment is carried out with screw support legs.

To arrange a drain for washing machines in the sewer, you will need an adapter for draining with a drop at an angle of 45 degrees.

To connect washing machines to electricity, you will need a three.core cable with a cross.section of 2.5 squares in double insulation and a 4 amperes with a leak current of not more than 30 milliamps.

In addition, it is possible to use control equipment. voltmeter. How to connect a washing machine to the power grid in more detail we will consider below.

Table of the main causes of leaks of the flood hose

The causes of the malfunction Elimination
The connection of the nut of the hose with the unit fitting, the rubber gasket was worn out. It is necessary to carry the nut or replace the gasket with a new.
Damaged hose of water supply, external mechanical exposure or a long service life of the product. The place of water leakage can be in any place of the product, most often these are micro cracks that are difficult to immediately detect. It is necessary to remove the product and carefully check with good lighting. If the leak is detected, do not repair (glue). The best solution is to replace with a new.

To install washing equipment, you need to connect it not only to the mains, but also to water supply and sewage.

The new car should have an instruction or scheme where there is a step.by.step description of the installation. Even if the owner of the washing machine has the experience of introducing the machine’s hose device, you still need to carefully read the instructions that describe in detail the installation of each drain hose. As a result of the incorrect installation of the drain of the machine, water leak and destruction of the mechanism can occur, and negative consequences may occur.

Necessary tools and materials:

  • Fum.
  • Hoses.
  • Siphon.
  • Double hose for draining in the sewer.
  • Double water supply hose.
  • Electric drill.

In the absence of the required length of the drain sleeve, it can be increased, but incorrect and unreliable extension can lead to flooding of the apartment. It is better to purchase a hose that has the required length.

You can drain the water from the plastic sleeve of the equipment into the sewer system if this function is ensured by fixing the pipe located on the side of the sink or bath.

If the plum hose should be installed in the bath, it is necessary to ensure that water is drained qualitatively. It is this discharge of water during the operation of the washing machine that will prevent flooding in the room if the drain hose accidentally falls out of the structure.

Installation of the drain hose on the back wall of the washing machine is carried out at an altitude of about 80 centimeters from the end, which should not interfere with the plum. You can use another siphon.

From the second end of the sleeve, you need to start the connection using the main siphon, which prevents the smell of wastewater. This may require bending the drain hose in addition to creating the effect of water congestion, but not to prevent leakage to prevent the penetration of odors into the machine.

To connect the hose in the machine, there is a restriction on the height of the exhaust nozzle, minimum and maximum. To ensure high quality drain and prevent the flooding of the apartment through the car as a result of clogging of the sewer pipe, it will be necessary to leave an air gap. In this case, when washing, the water will not enter the sewer from the equipment, and the installed program will begin to work incorrectly. Here you need to take into account the level of lifting all the water in the bath or sink, which should be slightly lower, and the gap is higher.

Technical characteristics of the pouring hoses

  • maximum operating temperature 100 0 s
  • withstands pressure up to 80 bar
  • 42 liters/min throughput
  • The kit includes 2 gaskets ¾
  • has a security system of aqua-stop
  • maximum pressure 60 bar
  • maximum operating temperature 90 0 with
  • Two.layer system
  • Built.in protection against leaks
  • working pressure up to 20 bar
  • Special nuts against spontaneous unscrewing the hose
  • operating temperature 5-25 0 s
  • withstands pressure up to 90 bar
  • Suitable for bringing cold water
  • Metal braid
  • Metal sleeve

There is only one restriction relative to the length of the pouring hose: so that the total total length from the hose to the drain does not exceed 15 meters. This means that the maximum length of the flood hose should not exceed 3 m. Otherwise, the load for the drain pump will be too large, and it may break. The flood hose has a standard thread ¾ inch and is connected to a locking crane. The eyeliner to plastic tap pipes crashes easily and simply. In new houses and during the capital repair, a place for installing a crane for a washing machine is designed in advance.

If the house was not carried out in the house, and water pipes are not designed to connect the washing machine, then in this case the filler hose is installed in front of the bath mixer or stolen on the float valve of the drain tank. For this:

For sealing on the thread of the release of the float valve, wound the FUM tone. In the case of attachment of the pouring hose to the mixer, the mixer itself is removed, and the connection crane to the washing machine is wound on an eccentric with cold water, and the clutch with hot water is wound up. the clutch. the coupling. The mixer itself is installed on top of this. Of course, this is not the best option, but you never know, it will also come in handy. There are even special cranes for connecting to the float valves of the toilet tanks, as well as wall mixers.

The drain hose in the same way as a bay, they are included. It serves to drain the water used during washing. However, the length of the hose offered to the washing machine does not always allow us to reach the place of stock, so consumers have drain hoses no less than flood. They have a nozzle from both ends, and such a hose can be stretched in length. The pipes provide hermetic connection in the joints. Drain hoses have no technical characteristics and are designed only for natural pressure of drained water. The material for their manufacture is rubber, which, under the influence of hot water and detergents and bleach, cracks and bursts, despite the increase in wire spiral.

How to connect a drain hose?

Using a plastic guide drain hose is attached to the edge of the acrylic bathtub or sink. You can use a siphon from a washbasin as a plum, or buy a special double siphon with an additional withdrawal for the drain hose of the washing machine. If you do not have enough to drain the existing length of the hose, then this situation is easy to fix. It is necessary to purchase a plastic extension cord, another drain hose and two clamps. The hose leaving the washing machine is inserted into the plastic extension cord, and the second hose is inserted from the other side of the extension cord. Both hoses are fixed with clamps. Everything, the elongated hose can be connected to the sewer.

Replacing the drain hose is easier than a flood. This is due to the fact that in order to get to the base of the drain hose, you need to disassemble the washing machine a little and climb inside it. In some grades of washing machines, the drain hose is attached at the top of the case, and in some below. To find out what is the connection in your washing machine, you need to remove the cover of the washing machine. Although some brands, for example, AEG, Siemens and Bosch, you need to remove the front of the case

However, we will dwell on the replacement of the drain hose through the back of the case, as is done in brands Indesit, Ariston, LG, Candy, Ardo, Beko, Samsung, Whirpool. In these models, the drain hose is located in the lower part of the rear cover of the body. After removing the panel (this is done easily):

  • unscrew the screws, and the lid itself is easily removed;
  • Slowly remove the filter of the drain pump, preparing a rag and a bucket in advance;
  • Pour water out of the washing machine, having previously put a bucket and tilting it forward;
  • Remove the snail, which pre.unscrews bolts. It is best to photograph how the clamp was fixed to know how to fix the new one;
  • Relax the clamp fixing the hose to the pump and disconnect the hose. We pull it and take it out of the washing machine;
  • Install a new hose and fix it with a clamp in the same way as the previous drain hose was attached.
  • Install a snail and fasten other parts with self.tapping screws, as it was before replacing the hose. Before putting the rear panel cover in place, you need to make sure that the connection of the new hose is tightened.
  • Twist the self.tapping screw using the screwdriver, setting the back panel cover in place.

Extending Washing Machine’s Water Inlet Hose with Clamps | DIY #1

A completely different way to replace the drain hose in the models, where the hose is located on the front panel.

We take out the dispenser container. Then we remove the base panel, weaken the clamp fixing the door cuff, and uncover the cuff from the door of the door. Then the filter of the drain pump is removed (you also need to prepare a rag and a bucket). After the residual water produces, the front of the panel is removed. For this, screws are twisted with a screwdriver. The bottom of the wall of the panel must be moved to itself until the gap of 5 cm is formed. We put your hand there, and by touch, we are looking for a hatch lock device. We defend the connector with the wires from it. After that we pull the panel and remove it.

We have opened access to the drain hose. Fixing elements are removed from it, and the hose is disconnected from the pump. Remember the location of the hose and mounts. Disconnect and take out the hose. We connect a new hose, fix it and collect the machine, after checking the tightness of the connection of the hose to the pump.

In washing machines with vertical loading, the drain hose is located on the side. To replace it, it is necessary to do all those actions that were described in previous cases, only the back or front panel is removed, but the side.

Protective hose for the washing machine of the flooding with Aquastop

A device with protection against leakage is called aquastop. Standard hoses that were written above can burst-this usually happens due to aging, over time. If there are water leaks, flooding may occur.

The pipe with the system Aquastop reduces the risk of leaks to zero.

The hose with a special Aquastop protection device is a system where 1 tube is located inside the second. A special material is arranged between them, when exposed to water, it swells, which helps totor the protective valve, which will block the water.

  • Full.time mode. water passes inside the main bulk hose.
  • When damage occurs (tear or slow flow), water acts on a swelling.
  • The material swells and the valve is triggered, the water is overlapped, the flooring does not get wet.

Such hoses are characterized by a fairly large cost, when compared with standard ones, but provides guaranteed protection against the course and flooding of neighbors. It happens that it also happens that the washing machine, not even turned on, makes a set of water, in such a situation the hose with the system of the water area will not help.

Types of hoses of the bay

When buying a washing machine, consumers can not always objectively evaluate the quality of additional components. As a result, when connecting equipment or some time after the start of operation, problems may occur. Sometimes the reasons lie in the malfunctions of the hoses. There are several varieties of flooding tubes.

  • Simple rubber pipe. Its cost and quality are low.
  • Reinforced hose. Has a fortified outer layer made of stainless steel, and nylon braid. Compared to the previous variety, the product is more reliable, but 100% of the protection against leakage does not.

note! Aquastop system. disposable. She saves from leaks and helps to avoid material damage, but can protect only once. Then the hose has to be changed.

After the old tube of the washing machine is out of order, it makes sense to opt for high.quality reinforced products or those equipped with aquastop system. Fill tubes can have a fixed or adjustable length:

water, supply, hose, washing, machine, thread
  • hoses with constant size up to 5 m;
  • corrugated products that can be stretched to the desired length to connect the washing machine to the pipes;
  • tubes in the bay designed to install equipment away from pipes at a distance of up to 10 m.

Most of the manufacturers of washing machines produce spare hoses for their models. They can be separately purchased in stores. The choice of a product of a well.known brand also serves as an additional guarantee from the purchase of low.quality goods.

Sewage

You can also connect the drain of the washing machine to the sewage system in several ways.

On the edge of the bath or sink

The simplest solution is to hang a hose fixed in a regular fastener to the edge of the kitchen sink or bath. The obvious drawback of such a solution is that during washing a plumbing device cannot be used.

The simplest solution: the drain hose clings to the edge of the bath.

But frequent drainage of hot water with a detergent dissolved in it guarantees the absence of blockages: over 4 years of life in a service apartment with just such a circuit of water drain, I have never encountered sewage problems problems.

A tee under a siphon

The drain hose can be directed to the tee, installed in the sewage bell at the connection with the siphon of any plumbing device. Installation of the tee in the case of a prefabricated plastic sewage system takes no more than a couple of minutes.

All compounds of the drain with sewage should be sealed. Otherwise, the scentes of the sewage system will spoil your appetite.

Connecting a drain hose to a oblique tee between a siphon of a sink and a comb.

A tee in a comb

The most civilized solution is a separate tee for connecting a washing machine, cut into a sewer comb (intra.apartment sewer). In this case, you can safely use a direct tee.

I strongly advise you to build its upper withdrawal with a pipe at least 40. 45 cm long: part of the washing machines is deprived of a shut.off valve between the tank and the drain hose, and with a too low hose, water can be poured out of the tank by gravity.

water, supply, hose, washing, machine, thread

The most correct connection diagram to the sewage system is with a separate insert into the comb and a water shutter.

How to lengthen the drain hose?

The factory length of this element SMA-1.5-2 m. If you buy a replacement with a larger length, you will have to disassemble the device. Not everyone is suitable for this. It’s easier to make an increase, for this you will need:

With a tight connection, the clamps are not needed. you can save on them. However, these are inexpensive details. In order not to run after them in case of poor tightness of the connection, it is better to stock up in advance. The clamps will also have to be used if it is not possible to find the desired connector. Consider two compound options:

  • With a connector:

How to connect tap adapter for washing machine. Tricks you need to know

  • Fix the elements in the connector;
  • We fix it with clamps. if necessary;
  • Connect with SMA and sewage;
  • Run the test washing.
  • If there is no connector.
  • Need a tube of the corresponding size of rubber or plastic;
  • We string the tube on two connected elements. so that they are coasted along its center;
  • The tube should sit as tightly as possible. we enhance the fit with clamps.

You learned how to lengthen the drain, but this is only half. Now we will deal with the element according to which water enters cm.

But you can see everyone

Here is a brief description of all the connection schemes with which we are going to introduce the reader:

Image Description

Crane insert in front of the mixer in the bathroom

Crane insert between hard and flexible eyeliners

Crane (cranes) in a straight section of a steel water supply

Aqua-stop systems for flexible flood hoses

Similar systems protect washing machines from leaks. All washing machines according to the degree of protection are conditionally divided into three types: defenseless, partially protected and fully protected from leaks. One of the varieties of a partial system of protection against Aqua-Stop leaks is a valve that is installed between the feed crane and the pouring hose. Its principle of action is to determine the difference in pressure. If it is completely ripped off, then such a valve will immediately work if the flow rate of the outgoing stream exceed 10-13 l/min. If tightness was broken in it, and it just cracked, then such a valve will not work.

There are aqua-stop hoses that partially protect washing machines from leaks or a large drain of water. Its constructive feature is a high.pressure hose, which is built in the main flood hose. If it breaks, or its aluminum pressing weakens, then the water will reach the block in which the absorbent is located. After water hit, the absorbent will expand. This will lead to the fact that under the influence of the expansion of the absorbent, the fuse will shift, which will close the water supply valve. If your washing machines do not have any protection against leaks, then using such systems will help you avoid this. The only drawback is that in the case of a break it will need to be completely changed.

Consider the last type of protection against leaks that uses an electromagnetic valve with a float on a pallet (aqua-stop). Such protection against grooves is called complete. In this case, the pouring hose does not contain the absorbent, but the adjusted electromagnetic valve, which integrated a special drain program. When you need to download water, the voltage is supplied to the valve, it opens and the water enters the washing machine. When the water has gained, this valve closes and the machine continues software washing. If it was partially damaged and the liquid seeps, then the water enters the pallet along the internal drainage system, which is equipped with a special float. When the liquid in the pallet reaches a certain level, the float closes contacts that close all electromagnetic valves. Such a system guarantees complete protection against leaks, even if water flows from the washing machine itself.

The fill hose breaks quite rarely. However, if this happens, then such systems will help to avoid negative consequences. Also, if necessary, it can be lengthened.

Connecting hose to washing machine inlet hose. Tutorial

The optimal service life

Damage can lead not only to filling its own room, but a neighbor. In order to prevent this, you need to change them while. Usually their service life is from 1 to 10 years. Most sellers give a guarantee that does not exceed 1 year, and it is almost impossible to determine the full service life. Therefore, you need to constantly monitor their condition, and, if necessary, change. This is especially true for the plum hose, through which all outgoing garbage stream passes

Ordinary crane, can significantly increase the life. It is installed in the tee of the water fence in the machine. If after washing it overlap it, then the flood hose will not be constantly under water pressure. Consider that rubber, and it should not be subjected to a sharp difference in temperatures, otherwise it can crack.

About the author

| Denial of responsibility | Contacts |RSS