Water water supply hose leaks water

Elimination of the leaks of washing machines

There are currently washing machines in every apartment, and their proper installation and operation directly affects their operation. If there is suddenly flowing water from under the washing machine, then this is one of the main signs of a breakdown of the entire device or its components.

The possibility of eliminating a particular malfunction directly depends on its nature, so, some can also be cope with and manually. For example, if the washing machine flows during washing, and when typing is not observed, then the reason is likely to lies in the appearance of cracks or holes in components responsible for the direct supply of water for washing (in other words, due to impaired tightness of the entire system).

Important: in case of water detection on the floor when the device is included in the network, the main electricity supply to the apartment should be immediately transferred to the off position, and then remove the plug out of the outlet; And only then can the consequences of leaks be eliminated.

Causes of water leakage

Since the washing machine is a rather simple unit from a technical point of view, the causes of the appearance of leaks are reduced to two main factors:

  • Incorrect installation of the device (for example, the machine can stand at an angle or closely pressed to the wall of the room);
  • The poor quality of the materials of components or their irregular.

In order to prevent leaks for the first reason, it is enough to read the instructions; In the second case, the complete replacement of the failed element usually helps. So, if a washing machine flows from below, then you must first check:

  • Bulk hose, which in most cases is made of rubber. Budget devices usually have a standard type hose, a medium segment and above. a two.layer compaction;
  • The work of the pipes. In this and higher case, the machine occurs only when replenishing the tank, container for powder and additional supply of water from the outside.
  • The fullness of the dispenser (a retractable container for washing powder, flavorings, antistatics and other liquids). When working in normal mode, it should not be filled even by a third. Water from it can transfuse due to strong pressure (regulated by the tap) or a high degree of clogging of the filter lattice further (cleaned with a toothpick and pr.);
  • The degree of sealing the door with a sealing cuff. Once again, for the most part concerns budget models, since low.quality rubber over time can crack from constant exposure to high temperature when drying and becoming unusable.

To understand the further processes and location of the main structural elements, you should look at Figure 1. the main structural elements of the washing machine

The appointment of a flood hose

Pouring hose is a device for connecting a washing machine to the water supply system. Through it, water is supplied to the internal elements of the washing machine. In view of the pressure under pressure, the flood products are made using special technology using reinforcement. The usual material of manufacturing such an element is polyvinyl chloride with nylon pasting. The connecting parts can be made of plastic, aluminum or steel. If the fittings are plastic, you need to tighten and unscrew them by hand, without the use of wrench keys.

Connection of the water supply hose

Usually, when installing a water supply system, during the repair of an apartment or house, the installation sites of household units are in advance, the work of which is connected using water. These are primarily washing and dishwashers. In these places, an experienced installer necessarily sets special taps for connection. They subsequently connect special hoses for water supply.

The usual dimension of the taps ½ and ¾ with external thread. This dimension also has hose nuts. Connection is carried out with a closed crane.

Before fastening the tube, you must make sure that there are sealing gaskets. It happens that they are included and require installation. In some cases, they are simply lost during transportation. After making sure there are gaskets, you can connect a water hose.

Usually from the side of the machine connection to the fitting, the tube has a M-shaped form under 90 degrees for convenient connection. Holding the tube from twisting, it is necessary to wind the nuts on the connection crane and on the fitting. The sequence in this case does not play the role. The main thing is that when installing the unit, the pipe does not twist and not bend. With the opening of the water crane, the connection can be considered complete.

Causes of leaks

To recognize genuine causes of leaks, you need to carefully examine all possible problem areas. Diagnosis is performed after disconnecting the device from the network. The hoses are also better to disconnect, free the space to move the unit. There can be many reasons for the leak. Here are just a small part of them.

Incorrect operation

She leads to the fact that the washing machine begins to work not in full force, there are soot. If you follow all the recommendations for cleaning the filtration and drain systems, the risks of getting a leak will be minimal. The problem may occur if the hoses receive mechanical damage. Children, pets can become source of danger.

If the leak is not under the case of the machine, but in front, you should pay attention to the condition of the cuff. It is they who most often suffer from incorrect treatment

Incorrect selection of chemicals

When, when examining the washing machine, obvious traces of water leakage from the compartment for loading the powder are found, the cause may not only be blockage. If there is too much chemical for washing, or it has higher foaming than necessary, excess foam will look for a way out through the joints of the tray.

Manufacturing defects

Sometimes washing machines, even manufactured by the most famous manufacturers, have a factory marriage if the cause of the leakage was the refusal of one of the elements of the system. The leakage is most often caused by the installation of low.quality seals and nozzles. parts that are quite easily replaced by warranty.

Damage to the details

As a rule, leaks are associated with breakdown of parts only if we are talking about the drain system. The leak in this case will arise at the stage of spin or rinsing, when the water is dumped from the system. If the pump is faulty, the water will accumulate near the back wall. There is also a leak with a malfunction of the seals or bearings of the drum. The processor in the dispenser can be associated with damage to the drain valve.

When the water leaks through the cuff, it is worth paying attention to the work of the press. If this sensor, which is responsible for monitoring the water level, will fail, overflows will inevitably occur in the drum

The clogging of the dispenser

If it was found that water flows from the machine at the very beginning of washing, at the stage of water set, this can be caused by damage to the tray for detergents or hoses located nearby to it.

During the operation of the machine, the tray has the ability to clog with washing powder, not completely washing during washing. Over time, the holes through which water should penetrate the tray, and it does not have time to wash off the powder and get further into the tank. Excess water in this situation and flow out the front wall.

With prolonged use of the washing machine, hard tap water can lay a lime precipitate and clog holes through which water is supplied to the tray. In this case, the stream under pressure is forced to change her direction and pour past the tray.

The flow of the inlet valve or too strong pressure in the water supply system also leads to the flow of water.To eliminate the blockage, it is necessary to extract the dispenser from the hopper and thoroughly rinse the spare parts. A mandatory measure is an inspection of the bunker drain neck for an extraneous object that can interfere with the flow of water. In the event that a decrease in the pressure (for this it is necessary to partially block the valve) and the dispenser is not helped, the inlet valve should be replaced, which is able to increase the pressure when rinsing. You can also see how to clean the washing machine with citric acid.

Clarifying the causes of leaks and their elimination

First you need to carefully examine the washing machine. If you notice, for example, that water runs from under the door of the hatch, the reason is obvious-the tightness of the elastic cuff is disturbed. Inspection of the flood and drain hoses, the cuffs of the door and the dispenser will also help localize the malfunction.

A careful inspection of the technique will help localize the breakdown

If you remember which of the washing stages began to flow. for example, when rinsing or by spinning. this will also help in determining the source of the accident. Когда течет стиральная машина при наборе воды, сразу же проверьте заливной шланг и места его соединений.

Checking hoses

Start with a visual inspection of the flood and drain hoses along their entire length. It may be possible to immediately see a longitudinal crack or other damage.

Pouring hose damaged by pets

The cause of such damage may be a rearrangement of furniture, causing an overlap of the hose or its excessive tension, as well as other mechanical influences. If both hoses look intact, disconnect them from the machine and check as follows:

If there is a leak, a wet spot will appear on the paper in this place. Do not forget about the cam stuper, to which the flood hose is connected. the connection can be unreliable. After checking the hoses, connect them tightly to the unit.

Replace the spoiled hose with a new. You can purchase it in specialized stores selling washing equipment and accessories for it. If this is not possible, use waterproof glue and rubber patch to restore integrity.

Depressurization of the drain filter

The loosely twisted filter is most often the reason that the washing machine flows. This defect is easily detected if the puddle is small and is located under this part, for example, from the left angle. In many models, see the filter is in the right corner of the case.

Elimination of fluid leakage from a drain filter

Spin the filter, check its contents and clean it. Then screw it tightly, making sure that the efforts do not lead to a breakdown of plastic thread. After that, start the washing cycle again and make sure that the filter was the reason for the appearance of water.

Flow from powder receiver

In each smell there is a retractable tray where washing powder and washing additives are placed. During operation, these substances are washed out of the hopper with water. But if any of them, being poor-quality, does not completely dissolve when washing, there is a blockage in a mesh or small holes of the hopper. Another reason for this phenomenon may be poor quality water water.

Doster tray in washing machine

The liquid cannot quickly go through the dispenser, and part of it spills out. So there is a leak from the powder receiver. The defect is eliminated very simple: remove the tray and thoroughly rinse the net or holes in the bunker with a stream of water. Then install the dispenser in place and start the washing again by loading the powder.

Damage to the elastic cuff of the hatch

Mistresses do not always check the s of clothing, laying it in a drum machine. Among extraneous objects can be quite sharp. so that they can damage the cuff. So there is a leak from the door of the hatch.

The process of removing cuffs for repair

If the hole is small, eliminate damage with waterproof glue and elastic patch. Previously, the cuff must be removed, taking out the clamp, which holds it in the hole. It is better to install a repaired rubber part in place so that the patch is at the top of the hatch. Thus, it will be subject to smaller loads.

Replace Old Bathroom Water Supply Lines (Without Leaks!).- by Home Repair Tutor

If the repair does not bring results and the water continues to run from the door, you will have to replace the damaged cuff with a new. Watch the video to find out how the cuffs are replaced in the Indesit washing machine:

The bay pipe flows

Water enters the tank through a pipe pipe. From the vibrations created by the rotation of the drum, the place of connection of the part with the tank can be depressurized.

Place of connection of the pouring pipe with a tank in a washing machine

To restore the connection, the pipe will have to be removed. Thoroughly remove the remains of the old glue from its surface, as well as from the surface of the tank. After both surfaces are completely dry, connect the flood pipe with the tank using epoxy glue or polyurethane sealant for fixing. You can also use any other durable waterproof glue.

The pipe valve pipe flows

In order to check the integrity of the pipe and the tightness of its connections, remove the upper cover of the washing machine under which it is located.

Fill valve with two branched nozzles

Perhaps the clamps in the joints are weakened and the pipe leaks, then they will have to be tightened or replaced with new. In case of damage to the pipe, also replace it with new.

Drain

Such a problem may appear after a few months of operation. Due to vibration, the nozzles made of low-quality materials are damaged in the form of cracks. The tightness at the junction with a tank or pump can be disturbed.

You can learn about the common causes of water flow in washing machines from the following video:

About the author:

water, supply, hose, leaks

Electron engineer with many years of experience. For several years he was engaged in organizing household appliances, including washing machines. Loves sports fishing, water tourism and travel.

Found a mistake? Select it and press the buttons:

water, supply, hose, leaks

Washing machines are related to the emergence of “wash money”. In the 30s of the XX century, American gangsters used the laundry network as covering their illegal activity. Giving income from criminal activity for revenue received from cleaning clothes, they turned “dirty” money into “clean” money.

There is a washing machine “For bachelors”. Linen washed in such an unit does not need to be ironed at all! The thing is that the device does not have a drum: some of the things can be placed inside the container directly on the hangers (for example, jackets and shirts), and smaller things (for example, linen and socks). on special shelves.

The first officially patented washing machine was made of wood and was a box with a frame filled to half with wooden balls. Inside, the laundry for washing, the detergent and with the help of the lever moved the frame, which, in turn, forced the balls and wipe the linen.

Cosmonauts, being in the orbit of the Earth, solve the problem of dirty things with the original method. Clothes are dropped from a spaceship, and it burns in the upper layers of the atmosphere.

Fixing a Toilet Leak

In the XIX century, a lot of time was leaving for the washing of ladies’ toilets. The dresses were pre.opened, and then washed and dried each part separately so that the fabric would not deform. After washing, the clothes were sewn again.

For washing small things on the road or hotel, it is convenient to use a regular plastic bag. Socks or tights are kneaded inside the tied package with water and a small amount of detergent. This method allows you to pre.soak things and perform washing without damaging the fabric and without spending a lot of powder and water.

History is known when the kitten fell into the drum of the washing machine and, having passed the full washing cycle on the Woolen things program, got out of the unit whole and unharmed. The only nuisance for the pet was an allergy to washing powder.

Washing machines equipped with functions “without ironing” or “light ironing” can wash underwear and at the same time practically do not crush it. Such an effect is achieved due to a special approach to squeezing. it is performed at low speeds, with large pauses, and a small amount of water is preserved in the tank.

The expression “soap opera” (“soap”) did not accidentally arise. The very first series and show, whose audience made up women, were broadcast on television at a time when housewives performed cleaning, ironing and washing. In addition, to attract spectators to screens on the air, advertising rollers of detergents were often scrollful: soap and powders.

How to clean the steam generator from scale

Instructions for installing a ceiling drying-liana

DIY underwear dryer

What is the difference between a steam generator from a steamer: what is better to choose

How to choose a drying machine for home underwear: tips, parameters

Do.it.yourself renovator repair

How to choose a floor dryer for linen: tips, best models, video

How to clean the scapard of scale at home

How to use a converter for clothes, instructions

How to clean the TEFAL iron inside from scale at home

How to get rid of mold in a washing machine

DIY: How To Fix a Broken Main Water Line Pipe

Common breakdowns of washing machines indesit

Causes of leaks and their elimination

The operation of the washing machine is associated using water of various temperatures, stiffness and detergents, which are chemical compositions with active elements of various nature. As a result of exposure to such an aqueous solution, and even with organic impurities of pollution from linen, it affects the physical properties of metal parts, oil seals, rubber cuffs, tubes and plastic elements.

As a result of the exposure of the aggressive environment and vibration, bearing nodes are destroyed, cracks or breaks of the hoses appear, the tightness of the compounds of the nodes and parts is disturbed.

Refrigerator waterline leak clever fix, detailed step by step repair instructions

The causes of leaks, as a rule, are established by a visual inspection for characteristic traces. Most often, leaks occur due to the following faults:

Violation of the functioning of the bearing

In order for the drum to make rotational movements, its body is rigidly attached to the shaft, which drives the electric motor. The shaft, depending on the structure, has one or more bearing components consisting of an omentum and a bearing. Most washing units use ball radial bearings of a closed type, as well as seals designed to protect them. To make sure the lifting of the seal, it is necessary to remove the rear cover and inspect the tank from the side of the bearings. Usually with a faulty seal, a leakage of water at the washing machine occurs during push. The oil seal (sealing rubber cuff) is made of special rubber, silicone rubber or polymer, adjacent to the working surface to the shaft, isolation of the interior of the bearing node from the water. A sleeve made of grinded bronze or brass alloy is pressed under the cuff on the shaft, so the sliding of the cuff edges passes almost perfectly, which makes it possible to completely prevent liquid from entering the bearing. To protect the oil seal from an aggressive environment and compact the node, it is filled with a special lubricant, usually having a silicone base. Lubrices should have a certain degree of moisture and heat resistance, characteristic of viscosity and not aggressiveness in relation to the materials from which the oil seal is made.

Car lubricants of the Litol type based on oil products are not suitable for lubrication of bearing nodes and may have a destructive effect!

The first sign of violation of the work of a bearing node is the appearance of noise during washing, especially at high speeds in spin mode. The oil seal begins to let water into the bearing, and all the lubricant is washed out, then its corrosion and increased wear occur. Often this leads to its complete destruction, as a result of which the washing machine begins to flow and the water is on the floor. The leak in the bearing node is eliminated by replacing the omentum and bearing. This operation for certain brands of machines is carried out using special devices in the conditions of service centers. Of course you can replace the bearings with your own hands, but this process is quite laborious and takes a lot of time. For washing machines with vertical loading on sale, there are flanges, which are already a ready.made bearing node with an oil seal and a bearing.

A crack in the tank

The material of the manufacture of tanks is special heat.resistant plastic. Over time, physical properties change and cracks and chips can form on the surface. The hit of a solid object between the drum and the tank can also cause damage it. If water flows from under the washing machine at the stage of water set, violation of the integrity of the tank can be one of the probable causes of the formation of a puddle under the machine. The best option is the purchase of a new tank and its installation in the service center. Many craftsmen are trying to eliminate the leak with the help of glue, and rubber patch. The use of epoxy glue can also have a positive effect, but in both cases this is not for a long time. Vibration loads and temperature differences will continue the process of cracking, and over time, the water will again be on the floor. You can also eliminate the crack by point heating using a soldering station.

Damage to the loading hatch cuff

In case of foreign objects, forgotten in the s of things in the washing drum, during washing, they can be damaged by the sealing cuff on the door. The cause may also be a banal wear of rubber or improper closure of the door, which leads to a crest cuff. As a result, the tightness of the hatch is disturbed and the water spilled on the body on the floor. In any case, check it for integrity, this is not difficult and does not take much time. If the defect was detected, you can repair cuffs on the spot with glue and rubber patch, which, for example, are used to repair inflatable boats. Then it is desirable to turn the cuff so that the glued part is on top. If the flow in this way could not be eliminated, the cuff must be replaced with another. To replace the cuff, it is necessary to use two screwdrivers a metal clamp located in the front of the cuff and carefully remove it. This clamp looks like a metal ring with a spring connection. The inside of the cuff holds another metal clamp located on the outer surface of the tank. To get to it and remove, it is necessary to dismantle the upper cover, weaken the bolt with a conventional cross blade, then put the clamp and pull it out of the grooves. Next, it is necessary, from the outside of the machine, stretch the cuff along with the clamp. To qualitatively put the cuff in place, do without removing the facade. Having removed the front cover, the cuff must be put on the plastic tank edging along the entire contour, falling into special grooves. After that, the rear clamp is installed and delayed. Then the facade is assembled, and the cuff is put on his ledge. At the end of the work with two screwdrivers, the front lock ring is carefully installed in place. After the repair, it is necessary to make sure that the loading hatch freely closes, providing the necessary sealing.

Checking the tightness of the compounds and cleaning of dirt

All elements responsible for the circulation of water in the washing machine are interconnected by means of nozzles and hoses. The elements of the compounds made of corrugated or simple rubber are torn over time or cracks appear in them. If, upon examination, leaks are detected in certain areas of pipe and hoses, they should be replaced entirely. At the same time, it is better to purchase new fasteners (clamps) to be confident in the reliability of the compounds.

Most often, the pipes of the tank and the intake valve flow due to the weakening of the clamps, as well as the damage to the pipes themselves.

Fault for the powder compartment

As washing, the machine takes the required amount of washing powder or liquid, rinseum from the powder receiver. Powder and other compounds are washed out with water coming during the cycle. The bunker is supplied with a mesh so that insoluble large lumps cannot get into the drum, do not cause clogs.

But the mesh itself is clogged from this. Water into the powder receiver enters for leaching, but cannot leave for the tank along with the powder because of the clogging. The clogging of the mesh is possible due to low-quality tap water-stiff, with an admixture of rust.

You can solve the problem yourself. It is necessary to extract the tray, rinse the filter set, the bunker dispenser. After drying, the tray is installed in place, launched washing for verification.

Malfunction of the pipes

Strong vibrations occur during the spin process. Когда изношены амортизаторы, обеспечивающие плавное вращение барабана на больших оборотах, вибрации настолько сильные, что машина может сдвигаться с места. This is a common cause of pipe damage.

To solve the problem, you need to remove the pipe, remove the remains of the adhesive layer and, using epoxy or similar glue, install back. It is better to call the service wizard for repairs, since not every owner of household appliances will be able to reliably glue the part for a tight connection with a pouring hose.

A filling pipe fails for the same reason. If the damage is at the junction with the tank, then you can try to glue it or tighten the clamp. In other situations, the detail cannot be restored. replacement is required.

The water supply hose at the washing machine flows: what to do

Washing machine. one of the main household appliances. It will help to keep clothes clean, so any malfunctions are critical. If something happened, you need to call the master, although there are breakdowns that are not difficult to eliminate on your own.

Leakage of the launch of the washing machine is not uncommon. The problem is indicated by the puddle on the floor during washing. Do not let the problem on its own and soak the water steadily. Such a malfunction is fraught with short circuits, boats of the house of households. You need to determine the exact fault. Among the possible options-breakdowns, excesses, defects of the hose, or the hose remains whole, and the leak is due to the wrong joint of the structure with the tap. A poor connection also leads to leaks, it occurs if the master has poorly twisted the structure, there was an outrage.

Make sure that the hose has the correct location. If he bent, pushing, leaks occur. Reinstallation will solve the issue. you just need to change the location of the node. Laying wear is also fraught with leaks. As a result of increased water pressure in the system, mechanical effects of the gaskets wear out, a leak arises. Possibility, difficulty with poor.quality docking of rubber and plastic inside the hose. Rubber is not eternal, over time loses its original form, elasticity. The quality of fixation suffers, water oozes during washing.

It is not difficult to replace the hose on your own, it is not necessary to contact the master for these purposes. It is necessary to turn off the water supply using the valve, remove the old hose from the machine, unscrew its access points to the water system. After connecting a new product, perform high.quality tightening fasteners, turn on the water.

Be sure to check whether the leak is preserved. If the twist is dense, the hose is set at the correct angle, the leaks should not be. The presence of leaks after replacement. the occasion to tighten the nuts in the areas of the fasteners. Nothing should be squeezed, it can lead to a breakdown of the thread. It will be better to repeat the attempt and wrap the nuts on the thread.

Another option for eliminating leaks. lengthening the hose. For normal operation of the machine, the length of the product should be up to 3 m, less than necessary, also undesirable. If the working fragment is short, it is expanded.

Eliminate leaks in the LG washing machine

Bought a couple of years ago a LG washing machine at the urgent request of my UKVO. Before that, Ardo had been successfully used for many years and continue to successfully use further, but SKVO said: “I want a new one, t.to. The old no longer struck “. I still can’t understand the feminine logic about how the automatic machine can no longer “break through”, but after the second or third hundred “I want a new one” surrendered. And this miracle of South Korean thought and Russian assembly stood up instead of Ardo, and the old woman Italian moved to Shurin, where she still works successfully. I apologize for many letters, now to the point.”Ski” flowed. Very quickly quickly after the purchase, I dripped, then it began to flow more and more. Putting a rag during washing stopped saving. Googled the problem and it turned out that this disease is chronic for “skiing”. They flow almost all of the tray for powders-gels. over, there are several places and causes of leaks: 1. The trays themselves flow around the entire perimeter of the upper and lower part of the tray. For understanding. “back” will call the motionless part (or niche) into which the box for powder (or gel) is pushed by. Flows the connection place of the tray and front wall of the machine; 3. Begins to spray and flow into the gap above the drawer, which is inserted into the tray, t.to. After a certain amount of junction of the leadership, the box on its scenes sip plastic influxes, pressing the box upwards upwards; 4. A rubber corrugated tube goes from the tray into the drum, along which, in fact, water with powder is already entering the drum. There is an interesting moment. South Koreans so placed this tube that it with its lower knee rubs on a balancing stone (such a healthy fool designed to extinguish vibrations) and rubs over time to a hole. The stone is like a sandpaper, you can sharpen knives 🙂 I think, they deliberately laid such a flaw, now all manufacturers of equipment are trying to make so that the equipment begins to break immediately after the guarantee.In general, we begin a comprehensive elimination of the problem and the petty refinement of “skis”.one. We push the machine from the wall, unscrews two screws on the back and left on the back wall, which hold the lid. Pour the lid from the front to the side of the wall, it moves from the front clamps-drills located under the lid, remove the lid, remove it to the side.2. We put forward a powder box, on the right and left of the tray we see two screws, turn them away, move the freed tray back and right, the tray is removed from the latch on the left wall and “falls” inside.3. Gently remove the hoses from the tray, weakening with the plots of the clamps. Two hoses supplying water (they are attached to the rear wall of the tray) and a corrugated hose, which removes excess air from the drum, annexed to the right wall of the tray. We take a little tray to the right and on the left we see the thickest corrugated hose of water supply to the drum. So he is rubbed on a stone. This hose is attached to the tray with a rubber loop. Remove the loop from the hook on the tray, remove the tray, remove it to the side. The disassembly process has completed. Uff!four. We examine this thick hose, if we frayed, we order a new one or a “collective farm” from a self.made one from what is. I turned out to be whole (praise of heaven), but the process clearly went, the trace of the stone is visible.5. My solution. we take a thick dense cellophane and glue a strip under the hose to the stone, t.e. deprive his pleasure to sharpen the hose. I did not find a thick dense cellophane, so I cut off a strip from a plastic one and a half. I glued it at the moment. On top sprayed the place of touching the hose with silicone grease. I think now the hose will not overlap until the next “no longer lasts, let’s go buy a new” 6. We disassemble the tray itself. It’s simple. The cover is simply clicked on latches. The plastic is not fragile, which is surprising, the latches are all intact.7. We apply silicone sealant around the entire perimeter of contact parts of the tray, collect in a heap.eight. We also apply a sealant on the edges of the tray, where it is pressed to the front cover of the machine.9. We collect everything in the reverse order, remove the cloth of the excess sealant inside the tray. The sealant usually dries for a day, takes the shape within 4 hours, so it is advisable to periodically extend and push the powder box during the first 4 hours so that the guide grooves are not clogged with a dried sealant.

So we coped with almost all the causes of leaks except one. loose pressing the box to the upper edge of the tray. This is if clutching influencers. On the Internet, the masters are advised to stick the strips of plastic on the erased influxes, you can, but a little hemorno to adjust the thickness of these strips. There is a more interesting solution. The front cover of the box is assembled from two parts. the external beautiful with the LG logo and the internal. in fact, the wall of the box. Between them a very decent gap, in which a powerful magnet is very comfortable in the upper part. And in the upper cover of the machine is also ochering voids on its entire front side, where you can easily glue a metal strip. I torn from the old murdered computer hard drive, very powerful and compact. I recommend.

When the box is pushed into the tray, the magnet pulls it up, there are no gaps.The last reason for the leak is eliminated.For many words, stupid typos and lack of photo, please do not kick much. When I did not think about writing a post with a machine, I almost didn’t take a photo, I thought I was delayed when I had already put the tray in place, I suddenly thought, there were many “happy” owners of a rag of rags, suddenly helped, painted everything as much as possible Details.All good!

About the author

| Denial of responsibility | Contacts |RSS