What are the transport bolts in the washing machine


Some users make the mistake of inexperience and forget to remove the bolts before using the washing machine or neglect to install them during subsequent transport.

What happens if you don’t remove the fasteners

The washing machine is designed for a long life, but just one mistake in the form of not removed drum fasteners can significantly reduce it, and sometimes make the device completely unrepairable.

During washing, the drum rotates smoothly and gently, and the load is evenly distributed. If you do not unscrew the fasteners, they will interfere with the free operation of the drum when starting the wash. Vibration and beating will spread to the housing, the bearings and motor will be under stress.

Externally, this will be manifested by strong jumps, especially during spinning, and the presence of extraneous noises. During such operation, the internal parts of the device and the drum itself are damaged, which will require expensive repairs or complete replacement of the “washing machine” in the future.

How to Reinstall

Keep in mind that the shipping bolts must be put back in case of re-shipment (moving, selling, etc. д.).

This will require three simple steps:

  • Removing plastic plugs.
  • Insert each bolt into the hole and push it in slightly so it doesn’t fall out.
  • Screw them clockwise into the holes, thus locking the position of the drum.

Can be shipped without them

Just one irregular shipment is enough to cause the washing machine to break down. Attempting to transport the appliance improperly will result in internal and external damage, for example:

  • damage to the power cord;
  • Dents, cracks and chips in the plastic parts of the machine, including the internal compartment for powder and other detergents;
  • Damage to the water intake and drain hoses;
  • tear of the cuff and breakage of the hatch fasteners;
  • The program switch on the control panel is broken;
  • Wiring faults;
  • Damage to the drain pump.

If the fasteners are missing for some reason, which is often the case when re-shipping used appliances, you’ll have to fix the drum with improvised means.

How to remove

It is advisable to remove the protective mounts even before the washing machine is placed in its stationary place and connected to the utilities. When the unit is already placed back against the wall (this is the preferred location), it will be difficult to reach them.

transport, bolts, washing, machine

As an additional reminder to remove the transport bolts from the washing machine, plastic plugs are always included to cover the freed holes. They not only perform a decorative function, but also prevent the ingress of dust and moisture inside the unit, as well as muffle the noise of the running engine.

It is recommended that any of the following tools be used to remove parts that are unnecessary during operation from the unit:

  • A wrench of suitable size (10-15 mm);
  • A small universal wrench (with adjustable spacing between jaws);
  • pliers (in the absence of other tools).

How to remove Shipping Bolts from Front Load Washing Machine||Installation of Samsung Washing Machin

The safety fasteners are not screwed in tightly and it does not take much time or effort to remove them. They must first be loosened by turning the wrench counterclockwise, then remove them by hand together with washers and gasket. Sometimes a special key is supplied with the manual, which makes it easier to remove the fasteners.

What happens if the bolts are not removed?

Before using the washer-dryer, the transport screws must be removed. If they are not removed before the first wash, the fasteners will interfere with the smooth rotation of the drum during operation. The machine will start to vibrate, making a loud noise. In addition to external manifestations, at this point, the internal parts of the machine can be noticeably damaged up to complete deformation.

Failures that occurred due to failure to remove the bolts are not covered by the warranty. Because of violations of the operating instructions, the service center has the right to refuse the owner of a damaged unit for free repair, even with a valid warranty.

Fixing devices. What are they for??

To minimize the risk during transportation, they are installed at the factory; also, in various tilts during transportation, the internal parts do not contact with each other because the bolts hold the tank in one position.

What are transit bolts? why are they there and what should I do with them?

This also keeps the shock absorbers and bearings intact.

These are very important parts of the washing machine, because they reduce the amount of vibration when washing and spinning.

What happens if the bolts are not unscrewed?

In each manual, the installation of washing machines is painted step by step, and the removal of transport bolts is prescribed as a mandatory procedure. If they are not removed, the machine will not work properly. Damping devices when the drum is rigidly attached to the body cease to perform their function, which causes increased vibration during operation. This is especially noticeable in the spin mode. The unit in this case can move out of place, which in some cases leads to a breakage of the electrical, water and sewer connection.

The washing machine has a fairly large weight, and at high spin speeds its uncontrolled movement around the bathroom or kitchen can lead not only to a breakdown of the household appliance, but also to damage to plumbing or furnishings.

The shipping bolts are not fundamentally different from the standard bolts. They can be slightly larger in size, and are always equipped with a specially shaped plastic insert. The insert secures the drum in one position. The immobilized reel does not respond to the rocking and vibration that accompanies it throughout its journey. The general principle of design is to securely fix the drum by pressing it against the back panel.

To immobilize it in this way, three to six bolts are usually sufficient.

Design of fixing elements

On the body of the washing machine are pear-shaped holes with a small notch at the bottom. A bolt is placed in the hole, which is equipped with a plastic and steel washer. The plastic one is used on the side of the body, so as not to scratch the surface. The steel one is used as a tightening reinforcement where the retainer head will not destroy the plastic.

How to remove transit bolts from your washing machine or tumble dryer

The fastener also has a plastic drum that fits on the bolt. This drum with the bolt is inserted into the hole in the tank as far as it will go. Then the whole structure is lowered into the recess, thanks to which a secure attachment is made. The retainer is then screwed into the nuts on the tank of the machine.

Transport bolts in the washing machine

The automatic washing machine is no longer a luxury. It has become an indispensable assistant in almost every home.

In order to make the machine serve long and properly, it is necessary first of all to transport it properly to the consumer from the manufacturer.

transport, bolts, washing, machine


After buying a new washing machine, it is almost always necessary to transport it. even if the store, selling large appliances, is located next door. And the customer has no idea how long, in what conditions and by what means of transportation the machine was delivered to the store. The packaging for transporting the appliance differs from manufacturer to manufacturer. It can be a cardboard box, a Styrofoam box, a wooden liner.

But all manufacturers make sure to fasten the most important part of the washing machine. its drum. with shipping bolts.

The drum is a mobile part, suspended on special springs. When the machine is running, we observe its rotation and fine vibration, due to which the washing process takes place. When transporting the drum must be fixed firmly. Otherwise it can damage itself or damage the tank and other adjacent parts.

The transport bolts may look different, and their design is determined by the manufacturer. Usually it’s a metal bolt itself with a hex head, and various rubber or plastic inserts. Inserts are put on the bolt and ensure the safety of the surfaces around the fasteners. Additionally metal washers, plastic or rubber gaskets can be used.

The size of bolts for transportation varies from 6 to 18 cm, depending on the brand of washing machine, its design features and decisions of the manufacturer.

The functions of the transport fasteners

The design of washing machines is such that the tank with the metal drum inside freely swings inside the body. It’s great for laundry, but a disaster for transportation. With any shaking of the steel machine, the drum can damage the tank, especially if it is made of plastic.

To prevent this from happening, the equipment of the machine provides transportation fasteners. bolts with a hexagonal head and two washers. They secure all the insides of the unit and prevent it from breaking.

The bolts are 12-14 mm in diameter. In some brands you can find 10 mm bindings. The rubber washer makes direct contact with the body, and the steel washer tightens the attachment. The bolt also has a special plastic cylinder that fills the small space between the body of the machine and the internal parts, rigidly fixing the elements.

| Denial of responsibility | Contacts |RSS